• 전기화학회지
• /
• 제2권1호
• /
• pp.46-49
• /
• 1999

Electron-beam 증발장치를 이용하여 리튬 박막 2차 전지 양극용 lithium cobalt oxide 박막을 제조하였다. Stainless steel -기판 위에 입혀진 $LiCoO_2$ 박막은 열처리 과정을 거쳐 잘 발달된 hexagonal 구조의 (003)면을 나타냈으며, 3.9 V 부근에서 전위 평탄 영역이 나타났다. $LiCoO_2$, 박막은 증착속도가 증가함에 따라 Li/co 조성비가 양론비에 근접하였으며, $15{\AA}/s$의 증착속도로 제작한 경우 높은 방전용량을 나타내었다. 열처리 온도가 증가함에 따라 용량이 증가하여 $700^{\circ}C$에서 최대 값을 나타내었으나, 그 이상의 온도에서는 기판과의 반응 때문에 방전용량이 현저히 감소하였다. 박막 내부의 리튬과 코발트의 불균일한 조성은 초기 방전용량의 감소를 가져왔다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.41-41
• /
• 2018

안정적이고 효율적인 전력 공급을 위해 번화가 대로변 주변에 다수의 지상 변압기 및 개폐기가 설치되고 있으며, 이로 인해 불법 부착물로 인한 도시의 미관 훼손, 변압기 및 개폐기의 오염 등의 문제가 발생하고 있다. 따라서 각 산업체 및 연구 기관에서는 부착 방지용 코팅 도료 및 시트에 대해 다양한 연구개발을 진행하고 있으며, 현장에 적용되고 있는 사례도 있다. 하지만 현재 현장에 적용된 대부분의 제품들은 약 1년 정도의 시간이 지나면 고유의 기능을 상실하며, 도료 및 시트와 기판 사이의 박리가 일어나 우수한 성능을 보이지 않아, 결과적으로 도시에 더욱더 악영향을 주고 있다. 이러한 원인으로는 도료 및 시트의 성능 평가를 위한 다양한 규격들이 존재하지만, 테이프류 탈착 시 영향을 주는 인자(Factor)들이 명확하게 설정되어 있지 않고, 이에 대해 면밀하게 분석한 자료가 없으며, 정량적이고 객관적인 시험 방법이 고려되지 않고 있기 때문에 좋은 제품을 선별하기 어려운 상황이다. 따라서 여러 가지 제품들의 비교평가 및 기술 개발에 활용할 수 있는 가이드라인을 제시하기 위해 일반적으로 사용되고 있는 면테이프(Duct tape)를 이용하여 기판(Substrate)에 대해 다양한 인자를 기준으로 탈착 특성을 측정 및 평가하였다. 현재 지상 배전함 및 개폐기는 분체도장(Powder coating)으로 구성되어져 있으며, 그 모재는 탄소강(Carbon steel)으로 이루어져 있고, 소수의 경우 스테인리스(Stainless steel)를 사용하기 있기 때문에 분체도장(Powder coating), 탄소강(Carbon steel), 스테인리스(Stainless steel)를 기판으로 선정하여 탈착 특성을 평가했다. 탈착 특성에 관여하는 요인으로는 탈착 각도(Peeling angle), 탈착 속도(Peeling speed), 표면 조도(Surface roughness) 등이 있고, 상대 습도(Relative humidity)의 경우 탈착 특성에 영향을 거의 주지 않는 것을 확인했다. 탈착 시 각도가 클수록, 속도가 빠를수록, 조도가 작을수록 부착력(Peel resistance, N/cm)과 탈착 에너지(Energy, J)가 커지며, 탈착 특성에 영향을 주는 인자를 바탕으로 95% 신뢰도 구간을 적용한 탈착특성 모델링을 제시하였다. 이 모델링을 이용하여 실제 현장에서 발생할 수 있는 다양한 각도($90^{\circ}$, $180^{\circ}$)와 속도 범위(100 ~ 1500mm/min)에서의 탈착 특성을 추정하는 것으로, 좋은 성능 및 내구성을 가진 제품을 효과적으로 선별한다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1142-1143
• /
• 2006

Kinik Company pioneered diamond pad conditioners protected by DLC barrier ($DiaShield^{(R)}$ Coating) back in 1999 (Sung & Lin, US Patent 6,368,198). Kink also evaluated Cermet Composite Coating (CCC or $C^3$, patent pending) with a composition that grades from a metallic (e.g. stainless steel) interlayer to a ceramic (e.g. $Al_2O_3$ or SiC) exterior. The metallic interlayer can form metallurgical bond with metallic matrix on the diamond pad conditioner. The ceramic exterior is both wear and corrosion resistant. The gradational design of $C^3$ coating will assure its strong adherence to the substrate because there is no weak boundary between coating and substrate.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.270-273
• /
• 2002

Conditioning은 CMP(Chemical Mechanical Planarization)에 필수적인 공정중의 하나이다. Conditioning의 목적은 removal rate와 uniformity를 CMP 공정 중에서 일정하게 유지시키는데 목적이 있다. 예전의 conditioning disks는 stainless steel substrate 위에 diamond 입자를 올리고 Ni전기도금을 결합시켜서 사용하였다. 그러나, CMP 공정 중에 Ni의분해로 인한 금속의 오염과 diamond abrasive의 분리로 인하여 scratch 문제가 발생하였다. 이 문제를 해결하기 위해서 ceramic substrate와 그것을 정밀 가공하는 기술을 응용함으로써 본래의 conditioning disks가 가지고 있는 diamond 입자의 분리와 metals 분해의 문제를 해결할 수 있게 되었다.

• 한국표면공학회지
• /
• 제26권5호
• /
• pp.225-234
• /
• 1993

Titanium nitride coatings were deposited onto SUS304 stainless steel substrates pretreated by mechanical scrubbing, chemical etching at 50% HCl solution and Ar ion etching. Adhesion strength were measured by scratch tester and confirmed by SEM with EDS. Adhesion strength of Ar ion etched substrate was 10 to 15 times higher than that of mechanical scrubbed or chemical etched substrate. Ar ion etching brought about an uniform and fine spherical shaped surface, while chemical etching gave rise to a rough and irregular surface on SEM micrograph. It was suggested that higher adhesion strength might be caused by anchoring effect of Ar ion etched surface prior to TiN deposition.

• 한국표면공학회지
• /
• 제45권3호
• /
• pp.106-110
• /
• 2012

Oblique angle deposition (OAD) is a physical vapor deposition where incident vapor flux arrives at non-normal angles. It has been known that tilting the substrate changes the properties of the film, which is thought to be a result of morphological change of the film. In this study, OAD has been applied to prepare single and multilayer TiN films by cathodic arc deposition. TiN films have been deposited on cold-rolled steel sheets and stainless steel sheet. The deposition angle as well as substrate temperature and substrate bias was changed to investigate their effects on the properties of TiN films. TiN films were analyzed by color difference meter, scanning electron microscopy, nanoindenter and x-ray diffraction. The color of TiN films was not much changed according to the deposition conditions. The slanted and zigzag structures were observed from the single and multilayer films. The relation between substrate tilting angle (${\alpha}$) and the growth column angle (${\beta}$) followed the equation of $tan{\alpha}=2tan{\beta}$. The indentation hardness of TiN films deposited by OAD was low compared with the ones prepared at normal angle. However, it has been found that $H^3/E^2$ ratio of 3-layer TiN films prepared at OAD condition was a little higher than the ones prepared at normal angle, which can confirm the robustness of prepared films.

• 한국재료학회지
• /
• 제13권9호
• /
• pp.587-592
• /
• 2003

The thin films of 316L stainless steel were made on glass and S45C substrate by Ion beam assisted deposition with reactive atmosphere of argon and nitrogen. The films were deposited at the various conditions of ion beam power and the ratios of Ar/$N_2$gas. Properties of these films were analyzed by glancing x-ray diffraction method(GXRD), AES, potentiodynamic test, and salt spray test. The results of GXRD showed that austenite phase could be appeared by $N_2$ion beam treatment and the amount of austenite phase increased with the amount of nitrogen gas. The films without plasma ion source treatment had the weak diffraction peak of ferrite phase. But under the Ar plasma ion beam treatment, the strong diffraction peaks of ferrite phase were appeared and the grain size was increased from 12 to 16 nm. Potentiodynamic polarization test and salt spray test indicated that the corrosion properties of the STS 316L films with nitrogen ion source treatment were better than bulk STS 316L steel and STS 316L films with Ar ion source treatment.

• 한국표면공학회지
• /
• 제34권5호
• /
• pp.465-474
• /
• 2001

Type 304SS coatings were performed at 200$\square$ onto AISI 1045 carbon steel substrate using unbalanced magnetron sputtering (UBMS) with an austenitic AISI 304 stainless steel (SS) target of 100mm diameter. The total deposition pressure in the active Ar gas was 2$\times$10$^{-3}$ Torr. Coatings were done at various target power densities and bias voltages. Chemical compositions of metallic elements of the coatings were measured by energy dispersive X-rays spectroscopy (EDS). The structure and the morphology of Type 304SS coatings were investigated by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). Corrosion properties of the coated specimens were examined using electrochemical polarization measurements and electrochemical impedance spectroscopy in a deaerated 3.5% NaCl solution. The porosity rate was obtained from a comparison of the dc polarization resistance of the uncoated and coated substrates. Scratch adhesion testing was used to compare the critical loads for different coatings. XRD results showed that the sputtered films exhibit a ferritic b.c.c. $\alpha$-phase. Potentiodynamic polarization curves indicated that all samples had much higher corrosion potential and better corrosion resistance than the bare steel substrate. The corrosion performance increased with increasing power density and the adhesion was enhanced at the bias voltage of -50V. An improvement in the corrosion resistance can be obtained with a better coating adhesion. Finally, an optimized deposition condition for corrosion protection was found as $40W/cm^2$ and -50V.

• 한국표면공학회지
• /
• 제31권1호
• /
• pp.34-44
• /
• 1998

Stainless steel is being used widely lor various purposes due to its good corrosion resistance. There has becn much research to produce colored stainless sterl by several methods. In this experiment, we coated TixN film on the SUS304 substrate with thc DC magnetron sputtering system and studied the internal structurc and adhesive strength of the films as a function of the coating conditions. Before lhe specimen was coated, a sputter etching was very effective in removing the$\delta$ Fe(BCC) phase as well as the contaminant and oxide layer as well as increasing rotghness. Five-stage failure mode appeared with increased scratch load with the TIN films coated on the SUS304 in this manner ; tensile failure-,conformal failure-,buckling failure->chipping failurc and spalling Failure. When the failure was terminated at the initial stage, the film will have good adhesion. But, if syalling failure has occurred at the initial scratch, then the adhesion will be poor. The interlayer between thc coated film and thc substratc was homogeneously adhcsive when the $\gamma'-Fe_4N$ phase wasn't detected in the XRD analysis and the adhesive strength only was reduced by surPace defects. But, when the ,$\gamma'-Fe_4N$N phasc was detected in the XRD analysis, the adhesive strength was very poor.

• Bulletin of the Korean Chemical Society
• /
• 제25권5호
• /
• pp.687-693
• /
• 2004

Composite membranes with a titania layer were prepared by soaking-rolling method with the titania sol of nanoparticles formed in the sol-gel process and investigated regarding the vapor permeation of various organic mixtures. The support modification was conducted by pressing $SiO_2$ xerogel of 500 nm in particle size under 10 MPa on the surface of a porous stainless steel (SUS) substrate and designed the multi-layered structure by coating the intermediate layer of ${\gamma}-Al_2O_3$. Microstructure of titania membrane was affected by heat-treatment and synthesis conditions of precursor sol, and titania formed at calcination temperature of 300$^{\circ}C$ with sol of [$H^+$]/[TIP]=0.3 possessed surface area of 210 $m^2$/g, average pore size of 1.25 nm. The titania composite membrane showed high $H_2/N_2$ selectivity and water/ethanol selectivity as 25-30 and 50-100, respectively. As a result of vapor permeation for water-alcohol and alcohol-alcohol mixture, titania composite membrane showed water-permselective and molecular-sieve permeation behavior. However, water/methanol selectivity of the membrane was very low because of chemical affinity of permeants for the membrane by similar physicochemical properties of water and methanol.