• Fibers and Polymers
• /
• 제3권1호
• /
• pp.14-17
• /
• 2002

Development of a novel fixed site carrier membrane (FCM), supported by PET fabric for metal ion separation is reported. The membranes were prepared by dipping PET fabric into the methylene chloride solution of Poly(5-vinyl-m-phe-nylene-m'-phenylene-32-crown-10) (P(VCE)), a polymeric metal ion carrier. It was found that the flux of mono-valent metal ion transported across the membrane is signif=cantly differed from each other and the flux decreases in the order $Cs^+$>$Rb^+$>$K^+$>$Na^+$>$Li^+$ irrespective to the anion except perchlorate anion. It was explained in terms of the stability of the complex, formed by crown ether unit of the P(VCE) and the various metal ions, meanwhile, the lower rate of transport in the presence of perchlorate anion was ascribed to its low hydrophilicity.

• 멤브레인
• /
• 제20권1호
• /
• pp.40-46
• /
• 2010

본 연구에서는 내열성 고분자인 폴리에테르술폰을 이용하여 전기방사의 방법으로 섬유 형태의 다공성 막을 제조하였다. 여기에 Nafion 용액을 함침 시켜 고분자 전해질 연료전지용 막을 제조하였다. 열중량 분석을 통해, 현재 고분자 전해질 막으로 상용화되어 널리 쓰이고 있는 Nafion 212보다 더 높은 열적 안정성을 갖는 것을 확인하였다. 주사전자현미경 측정을 통하여, 다공성의 폴리에테르술폰 막에 Nafion 용액이 수소이온 전도체로서 잘 함침 되어 있음을 확인할 수 있었다. AC impedance 측정 결과, $100^{\circ}C$ 이하의 온도범위에는 수소 이온 전도도가 $10^{-2}$ S/cm로 나왔으며, $100^{\circ}C$ 이상의 범위에서는 $10^{-3}$ S/cm의 값을 나타냈다. 0.6 V, $90^{\circ}C$의 조건에서 389 mA/$cm^2$의 전류밀도를 나타내었다. Nafion 212 상용 막이 $75^{\circ}C$에서 최대 성능을 나타내는데 반해, Nafion 용액을 함침시킨 폴리에테르술폰 막은 $90^{\circ}C$에서 최대 성능을 갖는 것으로 나타났다.

• 한국수산과학회지
• /
• 제48권5호
• /
• pp.589-595
• /
• 2015

Alginates are used to encapsulate various materials, including food, cosmetics, and pharmaceuticals. This study examined the properties and oxidation stability of fish oil capsules manufactured with calcium alginate gels. The fish oil capsules were manufactured by dropping sodium alginate solution and fish oil into a calcium chloride solution through nozzles. The membrane thickness, sphericity, rupture strength and deformation depth of the fish oil capsules were determined. The peroxide value of the fish oil was assayed to determine the oxidation stability of the capsules. The capsules measured approximately 3 mm with a membrane thickness of 90 μm independent of the amount of fish oil added. As the amount of fish oil encapsulated increased, the sphericity, rupture strength and deformation depth of the capsules decreased. The encapsulation efficiency increased until the amount of fish oil was 30%. The oxidation stability of fish oil in capsules was dependent on the type of nozzle, e.g., the oxidation stability of fish oil in capsules made using a double nozzle was greater than with a single nozzle. These results should lead to industrial application of fish oils including eicosapentaenoic (EPA) and docosahexaenoic (DHA) acids, as nutraceuticals.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1998년도 춘계 총회 및 학술발표회
• /
• pp.22-24
• /
• 1998

1. INTRODUCTION : The phase inversion method is widely used to prepare a variety of polymeric membranes ranging from micro-filtration to gas separation. The final morphology obtained by immersion precipitation strongly reflects the thermodynamics and kinetics of the system involved. The equilibrium thermodynamics of the ternary system of polymer/solvent/ nonsolvent is still very important to understand and predict membrane structure. Polysulfone (PSf) and polyethersulfone (PES) are important polymers as membrane materials due to the chemical resistance, mechanical strength, thermal stability and transport properies. There are several reports on the experimental phase diagrams in ternary mixtures of PSf/solvent/nonsolvent, and PES/solvent/nonsolvent. It would be interesting to investigate the solution thermodynamics containing these two polymers since PES is slightly less hyclrophobic than PSf.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1422-1424
• /
• 1994

This paper deals with piezoresistive humidity sensor using polycrystalline silicon (Poly-Si ) with membrane in sensors of semiconductor. Poly-Si piezoresistors which have no temperature dependancy are deposited on silicon wafer, membrane is formed with micromachining technology, then polyimide is formed as a hygroscopic layer. Whereas the principle of conventional humidify sensors are based on the change in electrical properties of the material, the humidity induced volume change of a polyimide layer leads to a deformation of a silicon membrane in this case. This deformation is transformed into an output voltage by Poly-Si piezoresistive. Wheatstone bridge. Fabricated piezoresistive humidity sensors showed good linearity, response time, and long term stability.

• Journal of Electrochemical Science and Technology
• /
• 제12권3호
• /
• pp.358-364
• /
• 2021

In this study, an anion exchange membrane water electrolysis (AEMWE) cell was operated for ~1000 h at a voltage bias of 1.95 V. Impedance spectra were regularly measured every ~ 100 h, and changes in the ohmic and non-ohmic resistance were traced as a function of time. While there was relatively little change in the I-V curves and the total cell resistance during the long-term test, we observed various electrochemical phenomena in the cell: 1) initial activation with a decrease in both ohmic and non-ohmic resistance; 2) momentary and non-permanent bubble resistance (non-ohmic resistance) depending on the voltage bias, and 3) membrane degradation with a slight increase in the ohmic resistance. Thus, the regular test protocol used in this study provided clear insights into the performance degradation (or improvement) mechanism of AEMWE cells.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.203-203
• /
• 2010

The proton exchange membrane fuel cell (PEMFC) is different from the normal power supply, and it is a nonlinear, multi-input, strong coupling, the complex dynamic system with large time delay. At present, many studies on the content of the fuel cell fuel cells focus on a static process, this paper analyzed in subsequent sections of the process of fuel cell dynamic response time of transition, and then it found the method to reduce the response time during the process of load change to ensure that the stability of output power.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1702-1703
• /
• 1999

We have prepared the plasma-polymerized membrane for pervaporation of organic-liquid mixtures by the plasma polymerization technique. Plasma polymerization techniques were utilized in the development of hydrophilic composite membranes having high hydrogen ion permeability and excellent dimensional stability. To develop an organic liquid permselective membrane. suppressing membrane swelling as well as enhancing the solubility difference is important, the objectives of the present study are to design a suitable membrane for an organic-mixture system by the control of the plasma-polymer solubility.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.173-178
• /
• 2008

This is green roof bottom system which composed by aluminum valve and glass fiber together as major reinforcement, so the cooper sheet can have root proof, and using recycled tire gel-type membrane waterproofing system which dost not contains VOCs. The copper sheet reduce the plants' root growing, so it helpes to maintain the waterproofing layer and stability of root proofing. Gel type membrane waterproofing system can do waterproofing, stress dispersion, and reducing leakage expansion. So those two materials can help each other to make green roof bottom layer would have the stability and durability.

• 멤브레인
• /
• 제34권2호
• /
• pp.154-162
• /
• 2024

음이온 교환막은 수전해 시스템에서 매우 중요한 역할을 하며, 생성된 수소와 산소 기체를 물리적으로 분리할 뿐만 아니라 전극 사이에서 수산화 이온의 선택적인 전달을 용이하게 한다. 음이온 교환막에 요구되는 특성은 수산화 이온에 대한 높은 전도도와 알칼리 환경에서의 화학적/기계적 안정성 등이 있다. 본 연구에서는 셀룰로오스 나노 크리스탈이 포함된 poly(terphenyl piperidinium) (qPTP/CNC) 복합매질분리막을 제조하였다. 고분자 매질로 사용된 poly(terphenyl piperidinium)은 super-acid 중합법을 통해 제조되었으며 이온전도성과 알칼라인 내구성이 뛰어난 소재로 알려져 있다. qPTP/CNC 분리막의 구조는 고분자와 나노 입자 계면의 공극이나 큰 응집체가 없는 조밀하고 균일한 형태를 나타냈다. CNC 나노 입자가 2wt% 첨가된 qPTP/CNC 분리막은 높은 이온교환용량(1.90 mmol/g)과 낮은 함수율(9.09%) 및 팽윤도(5.56%)를 보였다. 또한, 복합막은 수전해 작동 환경인 50℃ 1 M KOH에서 상용 FAA-3-50 분리막에 비해 월등히 낮은 저항과 우수한 알칼라인 내구성(384시간)을 달성했다. 이러한 결과는 친수성 첨가제인 CNC가 음이온 교환막의 이온 전도 특성과 알칼라인 내구성 향상에 기여할 수 있음을 보고하였다.