• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.283.1-283.1
• /
• 2016

Tin Oxide(SnO2) has been widely investigated as a transparent conducting oxide (TCO) and can be used in optoelectronic devices such as solar cell and flat-panel displays. It would be applicable to fabricating the wide bandgap semiconductor because of its bandgap of 3.6 eV. In addition, SnO2 is commonly used as gas sensors. To fabricate high quality epitaxial SnO2 thin films, a powder sputtering method was used, in contrast to typical sputtering technique with sintered target. Single crystalline sapphire(0001) substrates were used. The samples were prepared with varying the growth parameters such as gas environment and film thickness. Then, the samples were characterized by using X-ray diffraction, scanning electron microscopy, and atomic force microscopy measurements. We found that the strain evolution of the samples was highly affected by gas environment and growth rate, resulted in the delamination under O2 environment.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.185.2-185.2
• /
• 2015

Tin Oxide (SnO2) has been widely investigated as a transparent conducting oxide (TCO) and can be used in optoelectronic devices such as solar cell and flat-panel displays. In addition, it would be applicable to fabricating the wide bandgap semiconductor because of its bandgap of 3.6 eV. There have been concentrated on the improvement of optical properties, such as conductivity and transparency, by doping Indium Oxide and Gallium Oxide. Recently, with development of fabrication techniques, high-qulaity SnO2 epitaxial thin films have been studied and received much attention to produce the electronic devices such as sensor and light-emitting diode. In this study, powder sputtering method was employed to deposit epitaxial thin films on sapphire (0001) substrates. A commercial SnO2 powder was sputtered. The samples were prepared with varying the growth parameters such as gas environment and film thickness. Then, the samples were characterized by using XRD, SEM, AFM, and Raman spectroscopy measurements. The details of physical properties of epitaxial SnO2 thin films will be presented.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.88-91
• /
• 2000

The $(Sr_{0.85}Ca_{0.15})TiO_3$(SCT) thin films are deposited on Pt-coated electrode(Pt/TiN/$SiO_2$/Si) using RF sputtering method. The crystallinity of SCT thin films is increased with increase of substrate temperature in the temperature range of 200~500$[^{\circ}C]$. V-I characteristics of SCT thin films show the increasing leakage current with the increases of deposition temperature. The conduction mechanism of the SCT thin films observed in the temperature range of 25~100$[^{\circ}C]$ can be divided into four characteristic regions with different mechanism by the increasing current.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.62-65
• /
• 1997

Indium nitride thin films were deposited on Si(100) substrates by reactive sputtering method. The metallic indium target was sputtered by nitrogen gas with rf sputtering equipment. The surface morphology and cross-section of the InN thin films were investigated by scanning electron microscopy. The crystal orientations were investigated by X-ray diffraction and the Hall effect were measured with van der Pauw method. The indium nitride thin film showed high Hall mobility(215$\textrm{cm}^2$/V-sec) at 5mTorr total pressure and rf power 60W.

• 한국세라믹학회지
• /
• 제31권2호
• /
• pp.227-233
• /
• 1994

The Bi-Sr-Ca-Cu-O thin films were deposited by RF-magnetron sputtering method on Si(P-111) wafer without a buffer layer and annealed at various temperatures in oxygen atmosphere. The temperature dependence of electrical resistance, the microstructure of intermediate phase, and the surface morphology of films were examined by four probe method, XRD, and SEM, respectively. The chemical composition and the depth profile of the films were determined by ESCA spectra. Thin films annealed at $600^{\circ}C$ and $700^{\circ}C$ in oxygen atmosphere showed onset temperatures of 90 K and 85K, and Tc(zero) of 22K and 31K, respectively. The sample annealed at $700^{\circ}C$ had the highest volume fraction of superconducting phase and showed smooth microsturcture. In ESCA spectra, the thin films were homogeneous with depth.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.254-257
• /
• 2008

We have investigated the effect of source/drain electrode deposition method on a performance of top gate structured ZnO TFT performance. TFT using S/D of ITO film, consisted of bi-layer which deposited by ion beam assisted sputtering at the initial stage then deposited by DC magnetron sputtering, showed better performance compared to that using S/D of ITO deposited by just DC magnetron sputtering. Two ITO films exhibited different grain shapes and these resulted in different etching properties. We also suspect that charge trapping on the glass substrate (back channel) during the ITO film deposition may influence the characteristics of top gate structured ZnO TFT.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.246-246
• /
• 2008

In this work, VOx thin films have been deposited by DC magnetron sputtering method with various DC power. The characterization of the deposited thin films were changed by DC power. The experimental data are obtained on the growth rate and optical and electrical properties of VOx thin films with the increase of DC power. The growth rate. and the surface roughness decrease with DC power. Also, we investigated the electrical and optical properties of VOx thin films using hall measurement, 4-point probe, and UV-visible methods.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 제2회 학술대회 논문집 일렉트렛트 및 응용기술전문연구회
• /
• pp.40-44
• /
• 2000

$Bi_2Sr_2Ca_nCu_{n+1}O_y$($n{\geq}0$; BSCCO)thin film is fabricated via two different processes using an ion beam sputtering method i.e. co-deposition and layer-by-layer deposition. A single phase of Bi2212 can be fabricated via the co-deposition process. While it cannot be obtained by the layer-by-layer process. Ultra-low growth rate in our ion beam sputtering system brings out the difference in Bi element adsorption between the two processes and results in only 30% adsorption against total incident Bi amount by layer-by-layer deposition, in contrast to enough Bi adsorption by co-deposition.

• 한국전기전자재료학회논문지
• /
• 제13권9호
• /
• pp.796-800
• /
• 2000

Bi$_2$Sr$_2$Ca$_{n}$Cu$_{n+1}$ O$_{y}$(n$\geq$0; BSCCO) thin film is fabricated via two different processes using an ion beam sputtering method i.e. co-deposition and layer-by-layer deposition. A single phase of Bi2212 can be fabricated via the co-deposition process. While it cannot be obtained by the layer-by-layer process. Ultra-low growth rate in our ion beam sputtering system brings out the difference in Bi element adsorption between the two processes and results in only 30% adsorption against total incident Bi amount by layer-by-layer deposition, in contrast to enough Bi adsorption by co-deposition.on.n.

• 한국전기전자재료학회논문지
• /
• 제14권4호
• /
• pp.328-335
• /
• 2001

In this work, we made the precision thin film resistors of NiCr alloy (74wt%Ni-f18wt%Cr-4wt%Al-4wt%Cu) using DC/RF magnetron sputtering method and studied the sheet resistance and TCR(Temperature Coefficient of Resistance) etc... of the Ni-Cr-Al-Cu alloy thin film according to the change by annealing treatment to 400$\^{C}$ in air and nitrogen atmosphere and the change(power, pressure, substrate temperature) of sputtering process.