• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.4
• /
• pp.172-179
• /
• 1988

A cartridge type hydraulic logic valve consists of simple two port valve whose poppet is closed or opened by means of pressure signal of a pilot line. Accordingly, the logic valve can be used not only for direction, flow and pressure control purpose but also for versatile function valve which enables all above mentioned functions. In addition, the valve has little internal leakage and pressure loss, superior response characteristics and easiness in making small block type valve. The above mentioned good performances being recognized recently, the logic valve has been used widely in the large scale hydraulic system such as a hydraulic press system, for the performance requirements of high speed operation and precise control characteristics. However, there are scarce reports until now, except for a few ones from Aachen Institute of Technology in West Germany, so it is necessary to be studied on development and investigation for practical application. This paper showed that the static and dynamic characteristics of a logic valve when the logic valve is used for directional control, to investigate the relations between the valve operating characteristics and the valve design conditions. From the above mentioned procedure, it was ascertained that the valve operation characteristics obtained by numerical analysis showed good agreements with experimental results. The representative results obtained are as follows; 1. During the valve is closing, the poppet velocity is almost constant in the logic valve. 2. The pilot pressure P sub(3) and the resistance R in the pilot line have much influences on the valve operation time. 3. Spring strength have not such a severe influence on the valve operating time. 4. The operation characteristics of the logic valve can be estimated with good accuracy comparatively by numerical analysis with the equations describing poppet motion.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.91-98
• /
• 1997

Most dynamic systems have various random properties m excitation and system parameters. In this paper, a procedure for structural response and reliability analysis is proposed for the linear dynamic system with random properties in both excitation and system parameters. The system parameter and response with random properties are modeled by the perturbation technique, and then the response analysis is formulated by probabilistic and vibration theories. Probabilistic FEM is also used for the calculation of mean response which is difficult by the proposed response model. The first passage analysis by the integral equation method is used to analyze the probability of failure. The integral equation method results in the first passage probability in terms of crossing rates and first passage probability densities. In this study it is assumed that excitations, system parameters and responses are Gaussian. As an application example, the probabilities of failure at transient state are calculated for a sdof system with random mass and spring constant subjected to stationary white-noise excitation and the results are compared to those of numerical simulation.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.13 no.1
• /
• pp.73-79
• /
• 2001

In this study, a submerged plate-type breakwater is considered, which is supported by elastic foundation. This breakwater makes use of wave phase interaction among the incident, diffracted and radiated waves. We apply a three-dimensional singularity distribution method within the linear potential theory in order to describe the wave field. The submerged plate is assumed to be rigid and the elastic support be a linear spring with constant stiffness. A typical rectangle plate is exemplified for numerical calculation. The thickness of the plate is carefully selected in order to guarantee the solution to be stable by checking the condition number of the system matrix. A parametric study is carried out for examining the effect of the stiffness of the elastic support on performance of the breakwater. We also examine the effect of the submerged depth.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.7-7
• /
• 2010

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for Ubiquitous Sensor Networks(USN). In particular, the piezoelectric energy harvesting from ambient vibration sources has intensively researched because it has a relatively high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system has some drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure as shown in the figure. The natural frequency of a cantilever could be decreased to the usable frequency region (under 300 Hz) because the natural frequency depends on the length of a cantilever. In this study, the natural frequency of the energy harvester was a lower than a normal cantilever structure and sufficiently controllable in 50 - 200 Hz frequency region as adjusting weight of a proof mass. Moreover, the MEMS energy harvester had a high energy conversion efficiency using a shear mode ($d_{15}$) is much larger than a 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate for a standalone power generator for USN.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.1 s.74
• /
• pp.7-17
• /
• 2007

Based on the Boussinesq wave model, the wave distribution in the Chagui-Do sea area in Jeju was simulated by applying the directional irregular waves at an incident boundary. The time and spatial variations of monthly mean wave height and period were investigated, which aims to provide basic information on optimal sites for wave power generation. The grid size and time interval of the Boussinesq wave model were validated by examining wave distributions around a surface piercing wall, fixed at sea bottom with a constant slope. Except for the summer season, the significant wave height is dominated by wind waves and appears to be relatively high at the north sea of Chagui-Do, which is open to the ocean, while it is remarkably reduced at the rear sea of Chagui-Do because of its blocking effect on incident waves. In the summer, the significant wave height is higher at the south sea, and it is dominated by the swell waves, which is contributed by the strong south-west wind. The magnitude of significant wave height is the largest in the winter and the lowest in the spring. Annual average of the significant wave height is distinctively high at the west sea close to the Chagui-Do coast, due to a steep variation of water depth and corresponding wave focusing effect. The seasonal and spatial distribution of the wave period around Chagui-Do sea reveals very similar characteristics to the significant wave height. It is suggested that the west sea close to the Chagui-Do coast is the mast promising site for wave power generation.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.5
• /
• pp.67-74
• /
• 2008

Multi-layered stone masonry monuments, such as stone pagoda can be modeled as a multi-degrees of freedom system. The dynamic behavior of these structures are mainly influenced by contour condition of contacting surface of stones. In this case the mass of the system can be easily estimated, mean while the estimation of stiffness at junction is not simple. In this paper a method for estimating the spring constant at the contacting surface of stone in proposed. This paper describes a method of computational modelling technique for structural analysis of stone pagodas using measurement of natural frequency and eigenvalue analysis. For this purpose Five story stone pagoda in Cchongnimsa site was selected as a model.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.5
• /
• pp.477-483
• /
• 2015

In this paper, Euler-Bernoulli beam theories(EB-beam) are used, and Fast Fourier Transformation(FFT) analysis is then employed to extract their natural frequencies using both analytical approach and Co-rotational plane beam(CR-beam) EDISON program. EB-beam is used to analyze a spring-mass system with a single degree of freedom. Sinusoidal force with various frequencies and constant magnitude are applied to tip of each beam. After the oscillatory tip response is observed in EB-beam, it decreases and finally converges to the so-called 'steady-state.' The decreasing rate of the tip deflection with respect to time is reduced when the forcing frequency is increased. Although the tip deflection is found to be independent of the excitation frequency, it turns out that time to reach the steady state response is dependent on the forcing frequency.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2002.11a
• /
• pp.137-142
• /
• 2002

The purpose of this study was to examine the features that make residents feel “at home” in ALFs in Southwest Virginia and to suggest further policy and design guidelines for better Quality of ALFs as a “home.” For this purpose, residents' needs, experiences, and opinions of the physical environment, the social environment, and the organizational environments such as policies and programs of ALFs were identified. As a multi-case study, five ALFs in Southwest Virginia were studied using constant comparative methos of data analysis. In addition to face-to-face interviews with 25 residents and five administrators of five ALFs, observations were conducted with personal journal. Overall, the five sites selected presented homelike features showing the philosophy of assisted living which combines housing and services. Each facility was designed to be a single-family house or multi-family dwelling in outside appearance. As a whole, residents felt isolation and loneliness and they did not have active interaction with other residents because of diverse background among the residents. However, all of them had close relationships with the staff. The staff's attitude and behavior seemed to influence greatly the residents' feeling “at home.” Despite the provision of diverse activities by the facilities, many residents did not participate in the programs. Most of the residents agreed that the rule and regulations were fair. In spite of high satisfaction with the facility, many people did not think of their current dwelling as a real ‘home.’ As the biggest difference between living in their own homes and living in the ALF, people pointed out a lack of independence, freedom, and autonomy. Residents of ALFs may have reordered their priorities in their current life situation so that safety, security, and care were more important to them than feeling “at home.” Among the three factors --physical, social, and organizational-- that affect the residents' perception of ALFs as a “home, ” many emphasized the importance of social factors such as relationships with the staff and residents, and social support from their family or friends.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.8
• /
• pp.812-818
• /
• 2009

A MOV(Main Oxidizer shutoff Valve) controls the flow rate of liquid oxygen into the rocket combustor by opening and shutting operations piloted by a pneumatic force. In order to improve the effective design for sealing parts of poppet and piston assemblies, the poppet assembly has been designed to be just contacted with the piston assembly. However, to avoid a gap at the poppet/piston contact surface and to evaluate the MOV operating performance, an analyze on the force balance during the closing motion have been performed. For the accuracy of the analysis, the friction forces and the hydraulic forces have been respectively obtained by experiments and CFD analysis. Through the analysis, some important design parameters such as the spring constant, poppet friction and orifice size in the force balance have been introduced and the required operation performance of the MOV has been proved feasible.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.5
• /
• pp.676-684
• /
• 2020

This study was carried out in order to evaluate the bending creep deflection of glulams and bolted glulams beam-to-beam connection with steel-gusset plates and bolts under changing relative humidity. The two types of glulam beams (130 mm in width, 175 mm in thickness, and 3000 mm in length) used in this study were made from domestic larch and composed of seven layers. The gussets were made of 8-mm-thick steel plates. Creep testing was conducted under constant loads in an uncontrolled environment. The test was carried out in a room that was well ventilated through a window. The creep test specimens were loaded for 33,000 hours. A bending creep test for the glulams was conducted through four-point loading. The applied stresses were 20% and 30% of the MOR in the static bending test for the glulam and bolted glulam, respectively. After 33,000 hours, the creep deflection of the glulam at a 20% stress level increased by 39% to 99%, while the creep deflection of the glulam at a 30% stress level increased by 27% to 67%, as compared with instantaneous elastic deflection. The relative creep increased during autumn and winter, and recovered during spring and summer. The relative creep of the bolted glulams was changed abruptly by loading up to 5,000 hours, but stabilized after 5,000 hours, and then gradually increased until 33,000 hours. The relative creep of the bolted glulam increased 2.11 times on average after 33,000 hours.