• 한국정밀공학회지
• /
• 제34권2호
• /
• pp.151-156
• /
• 2017

Shot peening is widely used to improve the fatigue life and strength of various mechanical parts and an accurate method is important for the prediction of the compressive residual stress caused by this process. A finite element (FE) model with an elliptical multi-shot is suggested for random-angled impacts. Solutions for compressive residual stress using this model and a normal random vertical-impact one with a spherical multi-shot are obtained and compared. The elliptical multi-shot experimental solution is closer to an X-ray diffraction (XRD) than the spherical one. The FE model's peening coverage also almost reaches the experimental one. The effectiveness of the model based on an elliptical shot ball is confirmed by these results and it can be used instead of previous FE models to evaluate the compressive residual stress produced on the surface of metal by shot peening in various industries.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.108-117
• /
• 2005

In modern industrial society, many kinds of valves have been used to control fluid flow. For the optimization of a ball valve, a quarter of spherical ball was modeled and evaluated. However, there is a difficulty in the application of the optimization technique because of the complexity of the fluid and the restriction of analysis. Therefore, in this study, it is performed to evaluate the stability of an initial model using FEM(Finite Element Method) and CFD. In addition, a shape optimization design of the valve is accomplished using an orthogonal arrangement and characteristic functions. From the result, a new design method is represented that could overcome the time and space restriction in structural design, such as the divided ball valve with less experiment.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.283-288
• /
• 2011

액체 로켓 엔진의 극저온 고압 배관에 사용할 목적으로 구형 플랜지를 설계하였다. 설계된 구형 플랜지는 결합 부품 간 중심축이 최대 $2.5^{\circ}$의 오차가 있어도 플랜지 조립이 가능하며 기밀을 유지할 수 있어 엔진 조립 자유도를 증가 시킬 수 있다. 구형 플랜지는 볼, 소켓 형태의 결합부와 금속 실, 구형 볼트와 와셔로 구성되어 있다. 구형 플랜지 시제품을 제작하여 상온 기밀시험, 극저온 기밀시험, 상온 강도시험, 상온 파괴시험을 수행하여 성능을 검증하였다.

• 한국추진공학회지
• /
• 제15권3호
• /
• pp.64-69
• /
• 2011

액체 로켓 엔진의 극저온 고압 배관에 사용할 목적으로 구형 플랜지를 설계하였다. 설계된 구형 플랜지는 결합 부품 간 중심축에 최대 $2.5^{\circ}$의 오차가 있어도 플랜지 조립이 가능하며 기밀을 유지할 수 있어 엔진 조립 자유도를 증가 시킬 수 있다. 구형 플랜지는 볼, 소켓 형태의 결합부와 금속 실, 구형볼트와 와셔로 구성되어 있다. 구형 플랜지 시제품을 제작하여 상온 기밀시험, 극저온 기밀시험, 상온 강도시험, 상온 파괴시험을 수행하여 성능을 검증하였다.

• 한국강구조학회 논문집
• /
• 제29권6호
• /
• pp.443-453
• /
• 2017

본 연구에서는 데크형 중공슬래브의 중공률을 확보하기 위한 방안으로 기존의 중공슬래브에 일반적으로 사용되는 구형형상의 경량체 대신 사다리꼴 형상의 경량체를 적용하고, 이에 따른 휨 및 전단 내력 성능을 실험을 통해 확인하였으며, 일방향 데크플레이트의 설치방향에 따른 구조특성을 검토하였다. 그 결과 휨내력 측면에서는 기존 구형형상의 경량체를 가진 중공슬래브와 동등한 수준의 성능을 발휘하는 것을 확인하였으며, 전단내력 측면에서는 경량체 형상 변화에 따른 차이보다는 데크플레이트의 트러스철선의 기여에 따라 큰 전단내력성능을 발휘하는 것을 확인하였다. 중공체 설치시 콘크리트 유효단면의 감소로, 전단 강도가 약 50~60% 정도로 저하된다는 기존 연구에 따른 계산한 전단내력값과 비교하였을 때, 폭방향으로 데크를 설치하여 트러스철근이 전단에 영향을 미치지 않을 것으로 가정한 실험체도 트러스철근의 트러스프레임 거동에 의한 영향으로 저감 전 값 대비 87%의 성능을 보여 기존 연구에 따른 계산전단내력보다 최대하중이 더 크게 나타났다.

• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.13-17
• /
• 2016

It is highlighted that increasing the adsorbent surface area on volumetric basis is very important in providing an easy access for gas molecules. Fine particles around $3{\mu}m$ of soft-burned dolomite kiln dust (SB-DKD) were hydrated to wet slurry samples by ball mill process and then placed in a chamber to use spray dryer method. Spherical granules with particle size distribution of $50{\sim}60{\mu}m$ were prepared under the experimental condition with or without addition of a pore-forming agent. The relationship between bead size of the pore-forming agent and size of SB-DKD particles is the most significant factor in preparation of spherical granules with a high porosity. Whereas addition of smaller beads than SB-DKD resulted in almost no change in the surface porosity of spherical granules, addition of larger beads than SB-DKD contributed to obtaining of the particles with both 15 times larger average pore volume and 1 order of magnitude larger porosity. It is considered that spherical granules with improved $N_2$ gas adsorption ability may also be utilized for other atmospheric gas adsorption.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.183-187
• /
• 2012

In the present study, a feasibility study on an innovative satellite attitude control actuator is performed. The actuator is specially designed to generate the reaction torque in an arbitrary axis, so that a satellite attitude can be controlled by using itself. It consists of a spherical flywheel and electromagnets for levitation and rotation control of the ball. As the earlier study, a rotating performance test on the spherical actuator is conducted in a single rotating axis and vertical levitation condition. From the test results, it can be confirmed that the maximum speed and torque of the innovative device are 7,200rpm and 0.7Nm, respectively. Using torque-voltage characteristics of the spherical motor, an open-loop control (V/f constant control) is performed, and the test results show excellent control performance in acceleration and deceleration phases.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.201-206
• /
• 2004

Laser scanner are getting used for inspection and reverse engineering in industry such as motors, electronic products, dies and molds. However, due to the lack of efficient scanning technique, the tasks become limited to the low accuracy purpose. The main reasons for this limitation for usefulness are caused from the optical drawback, such as irregular reflection, scanning direction normal to measuring surface, the influence of surface integrity, and other optical disturbances. To overcome these drawback of laser scanner, this study propose the mechanism to reduce the optical trouble by using the 2 kinds of rotational movement axis and by composing the spherical coordinate to scanning the surface keeping normal direction consistently. So, it could be designed and interfaced the measuring device to realize that mechanism, and then it could acquisite the accurate 3D form cloud data. Also, these data are compared with the standard master ball and the data acquisited from the touch point sensor, to evaluate the accuracy and stability of measurement and to demonstrate the implementation of an dental tooth purpose system

• 한국기계가공학회지
• /
• 제19권3호
• /
• pp.71-76
• /
• 2020

Various machining methods are being studied to improve the processing quality of the spherical R shape in press die. In this paper, we confirmed that changes in machining quality were associated with changes in cutting direction, path, and cutting angle, which are commonly used in the machining of molds. We obtained a surface roughness graph with each condition change in one specimen using an instrument that measured geometry and surface roughness simultaneously. The results of the study showed that the best surface roughness in the finish cut of the spherical surface was obtained using upward pick feed machining.