• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.141-146
• /
• 1999

An experimental investigation on the leakage characteristics of a labyrinth seal, high-low seal, is studied. Pressure distribution and leakage flow rate are measured along with the shaft speed and the pressure difference between the entrance and the exit. Pressure distribution vanes almost linearly along the seal and the leakage flow rate increases as the increase of the pressure difference. Furthermore, it is found that both the shaft speed and the shaft vibration have no influence on the leakage of the labyrinth seal.

• Journal of Information Technology Applications and Management
• /
• v.22 no.3
• /
• pp.105-114
• /
• 2015

This paper presents a fast Time Difference of Arrival (TDOA) estimation for sound source localization. TDOA is the time difference between the arrival times of a signal at two sensors. We propose a partial cross correlation method to increase the speed of TDOA estimation for sound source localization. We do this by predicting which part of the cross correlation function contains the required TDOA value with the help of the signal energies, and then we compute the cross correlation function in that direction only. Experiments show approximately 50% reduction in the cross correlation computation time thereby increasing the speed of TDOA computation. This makes it very relevant for real world surveillance.

• Journal of Korean Physical Therapy Science
• /
• v.16 no.4
• /
• pp.49-57
• /
• 2009

Background: The purpose of this study was to assess the test-retest reliability of balance measurements in older adults using balance measurement system(Good Balance). Methods: The subjects consisted of 49 female and 20 male in community-dwelling older adults. This study used a repeated-measure design. Each subject completed all the different tests once and they were then repeated with 2 minutes in between. Repeated two-ways analysis of variance(ANOVA), representing two test times and both sexes, was calculated for each of the two dependent variables. Intraclass correlation coefficients(ICCs) were used to assess the test-retest reliability. Results: 1) There was not significant difference between test and retest for mediolateral sway speed and anterioposterior sway speed under conditions of normal standing with eyes open, normal standing with eyes closed and semitandem standing with eyes open. There was not significant difference between males and females for mediolateral sway speed and anterioposterior sway speed under conditions of normal standing with eyes open, normal standing with eyes closed and semitandem standing with eyes open. There were not the interaction effects between genders and test time under three conditions. 2) The reproducibility between test and retest was excellent for anterioposterior sway speed(ICC=.77) under condition of normal standing with eyes open, and for mediolateral sway speed(ICC=.76) and anterioposterior sway speed(ICC=.84) under condition of semitandem standing with eyes open. The reproducibility between test and retest was fair to good for mediolateral sway speed(ICC=.64) under condition of normal standing with eyes open, for mediolateral sway speed(ICC=.63) and anterioposterior sway speed(ICC=.75) under condition of normal standing with eyes closed. Conclusion: Balance tests in older adults using balance measurement system(Good Balance) demonstrated acceptable levels of reliability.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.149-161
• /
• 2022

Because the speed limit affects moving speed, it is closely related to traffic accidents as well as traffic flow. The existing speed limit calculation methods consider various engineering factors such as lanes, intersection spacing, driveways, crosswalks, 85 percentile speed, land uses, and roadway geometric characteristics etc. However, it can be said that the engineering analysis is insufficient because the traffic impact analysis considering traffic volume is not carried out. In addition, only 85 percentile speed, which is the spot speed, does not reflect the characteristics of the traffic flow on the road. In this paper, the effect of the speed limit change on the moving speed and the travel speed was analyzed in detail accordinr to the variation of intersection spacing and traffic volume. And by using the results, we proposed a speed limit calculation method that maintains the same service level as before the speed limit change, thereby increasing the speed improvement effect and reducing the difference between moving speed and travel speed. In addition, a variable speed limit operation method according to the change in traffic volume was also suggested. This method is expected to be effective in terms of safety by reducing the speed difference, which affects the severity of traffic accidents, while securing the speed improvement effect, and increasing the speed limit compliance rate of drivers by operating the speed limit that reflects the speed change due to the variation of traffic volume.

• Journal of Bio-Environment Control
• /
• v.5 no.2
• /
• pp.160-166
• /
• 1996

Objective of this study was to investigate the effects of all current speed on the microclimates above and inside the plug stand under artificial light. Maximum air temperature appeared near the top of the plug stand. Difference in air temperature inside the plug stand increased with the decreasing air current speed. Difference in relative humidity(DRH) to the relative humidity at the Inlet of the main air flow conditioner Inside and above the plug stand decreased with the increasing air current speed. Relative humidity inside the plug stand was 10-15% higher than that above the plug stand. DRH inside a stand of plug at air current speed of 0.3m s$^{-1}$ was about two times as many as that at air current speed of 0.9 m s$^{-1}$ . DRH inside the plug stand was 2.8-6.5% higher at LAI of 2.6 than that at LAI of 0.5. Gradient for the vapour pressure deficit was distinctly appeared at the low air current speed. Direction of vapour pressure flux is from the medium surface upwards. Difference in vapour pressure(DVPD) to the vapour pressure deficit at the inlet of the main air flow conditioner inside and above the plug stand decreased with the increasing height above the medium surface. DVPD inside the plug stand was 0.3-0.4㎪ higher at air current speed of 0.9m s$^{-1}$ than that at air current speed of 0.3m s$^{-1}$ . Results for the effects of air current speed on the relative humidity and vapour pressure deficit indicated that the microclimates above and inside the plug stand at the rear region in plug trays were slightly unfavorable compared to those at middle region.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.83-94
• /
• 1999

This study is about design of vehicle for air tightness to pressure waves of high speed train. When the train runs to high speed over 300km/h, the comfort of passenger come down due to difference pressure between inside and outside of passenger room. The car-body was carried out the design of air-tightness, and the analysis of inside pressure of vehicle in tunnel by TG_TUN of ALSTOM Co. The result of analysis should be used the design of air pressurized system and car-body of G7 high speed train project.

• Journal of the Korean Society for Railway
• /
• v.12 no.1
• /
• pp.65-71
• /
• 2009

The pressure transient inside the passenger cabin of high-speed train has been assessed using computational fluid dynamics (CFD) based on the axi-symmetric Navier-Stokes equation. The pressure change inside a train have been calculated using first order difference approximation based on a linear equation between the pressure change ratio inside a train and the pressure difference of inside and outside of the train. The numerical results show that the pressure change inside the new Korean high-seed train passing through a tunnel of Seoul-Busan high-speed line at the speed of 330km/h satisfied well the Korean regulation for pressure change inside a passenger cabin if the train is satisfying the train specification for airtightness required by the regulation.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.6
• /
• pp.47-54
• /
• 2021

The number of freeway traffic accidents in Korea is about 4,000 as of 2020, and deaths per traffic accident is about 3.7 times higher than other roads due to non-recurring congestion and high driving speed. Most of the accident types on freeways are side and rear-end collisions, and one of the main factors is hazard traffic flow caused by merge, diverge and accidents. Therefore, the hazard traffic flow, which appears in a continuous flow such as a freeway, can be said to be important information for the driver to prevent accidents. This study tried to classify hazard traffic flows, such as the speed change point and the section where the speed difference by lane, using individual vehicle information. The homogeneous segment of speed was classified using spatial separation based on geohash and space mean speed that can indicate the speed difference of individual vehicles within the same section and the speed deviation between vehicles. As a result, I could extract the diverging influence segment and the hazard traffic flow segment that can provide dangerous segments information of freeways.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.3-6
• /
• 2002

In a conventional speed sensorless stator flux-oriented(SFO) induction motor drive system, when the estimated speed is transformed into the sample-data model using the first-forward difference approximation, the sampled data model has a modeling error which, in turn, produces an error in the rotor speed estimation. The error included in the estimated speed is removed by the use of a low pass filter (LPF). As the result, the delay of the estimated speed occurs in transients by the use of the LPF This paper investigates the problem of a conventional speed sensorless SFO system due to the delay of estimated speed in the filed weakening region. In addition, this paper proposes a method to estimate exactly speed by using Luenberger observer, The proposed method is verified by experiment with a 5-hp induction motor drive.

• Journal of the Institute of Convergence Signal Processing
• /
• v.20 no.3
• /
• pp.171-176
• /
• 2019

Drones are highly utilized because they can efficiently acquire long-distance videos. In drone operation, the speed, which is the magnitude of the velocity, can be set, but the moving direction cannot be set, so accurate information about the drone's movement should be estimated. In this paper, we estimate the velocity of the drone moving at a constant speed and direction. In order to estimate the drone's velocity, the displacement of the target frame to minimize the sum of absolute difference (SAD) of the reference frame and the target frame is obtained. The ground truth of the drone's velocity is calculated using the position of a certain matching point over all frames. In the experiments, a video was obtained from the drone moving at a constant speed at a height of 150 meters. The root mean squared error (RMSE) of the estimated velocities in x and y directions and the RMSE of the speed were obtained showing the reliability of the proposed method.