• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.314-324
• /
• 1996

A high speed NMR quality evaluation sensor was designed , constructed and tested . The device consists of an NMR spectrometer coupled to a conveyor system. The conveyor was run at speeds ranging from 0 to 250 mm/s. Spectral of avocado fruits and one-dimensional magnetic resonance images of pickled olives were acquired while the samples were moving on a conveyor belt mounted through a 20Tesla NMR magnet with a 20 mm diameter surface coil and a 150 mm diameter imaging coil respectively. Fro a magnetic resonance spectrum analysis, motion through variations in the magnetic field tends to narrow spectral line width just like using sample rotation in high resolution NMR to narrow spectral line width. Spectrum analysis was used to detect the dry weight of avocado fruits using the ratio oil and water resonance peaks. Good correlations maximum r=0.970@ 50 mm/s and minimum r=0.894@250mm/s ) between oil and water resonance peak ratio and dry weight of avocados were observed at speeds ra ging from0 to 250mm/s. For the application of magnetic resonance imaging (MRI) method, the projections were used to distinguish between pitted and non-pitted olives . Effect of fruit position in the coil was tested and coil degree effects were noticed when projects were generated under dynamic conditions. Various belt speeds (up to 250mm/s) were tested and detection results were compared to static measurements. Higher classification errors were occurred at dynamic conditions compared to errors while olives were at rest.

• Restorative Dentistry and Endodontics
• /
• v.29 no.6
• /
• pp.504-514
• /
• 2004

This study compared the dentin shear bond strengths of currently used dentin bonding agents that were irradiated with an LED (Elipar FreeLight, 3M-ESPE) and a halogen light (VIP, BISCO). The optical characteristics of two light curing units were evaluated. Extracted human third molars were prepared to expose the occlusal dentin and the bonding procedures were performed under the irradiation with each light curing unit. The dentin bonding agents used in this study were Scotchbond Multipurpose (3M ESPE), Single Bond (3M ESPE), One-Step (Bisco), Clearfil SE bond (Kuraray), and Adper Prompt (3M ESPE), The shear test was performed by employing the design of a chisel-on-iris supported with a Teflon wall. The fractured dentin surface was observed with SEM to determine the failure mode. The spectral appearance of the LED light curing unit was different from that of the halogen light curing unit in terms of maximum peak and distribution. The LED LCU (maximum peak in 465 nm) shows a narrower spectral distribution than the halogen LCU (maximum peak in 487 nm). With the exception of the Clearfil SE bond (P < 0.05), each 4 dentin bonding agents showed no significant difference between the halogen light-cured group and the LED light-cured group in the mean shear bond strength (P > 0.05). The results can be explained by the strong correlation between the absorption spectrum of camphoroquinone and the narrow emission spectrum of LED.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.32-42
• /
• 2015

Orthogonal frequency-division multiplexing (OFDM) suffers from spectral nulls of frequency-selective fading channels. Linear precoded (LP-) OFDM is an effective method that guarantees symbol detectability by spreading the frequency-domain symbols over the whole spectrum. This paper proposes a computationally efficient and low-cost implementation for discrete Hartley transform (DHT) precoded OFDM systems. Compared to conventional DHT-OFDM systems, at the transmitter, both the DHT and the inverse discrete Fourier transform are replaced by a one-level butterfly structure that involves only one addition per symbol to generate the time-domain DHT-OFDM signal. At the receiver, only the DHT is required to recover the distorted signal with a single-tap equalizer in contrast to both the DHT and the DFT in the conventional DHT-OFDM. Theoretical analysis of DHT-OFDM with linear equalizers is presented and confirmed by numerical simulation. It is shown that the proposed DHT-OFDM system achieves similar performance when compared to other LP-OFDMs but exhibits a lower implementation complexity and peak-to-average power ratio.

• Wind and Structures
• /
• v.24 no.2
• /
• pp.185-204
• /
• 2017

High-resolution wind measurements at 2.25 m in height were used to investigate the mean and turbulence properties of an extreme thunderstorm wind event in West Texas. These data were combined with single Doppler scans from the Texas Tech University Ka-band mobile Doppler radars systems (TTUKa) to provide meteorological context over the surface measurement stations for portions of the outflow. Several features characteristic of a severe wind event were noted in the radar data, including a bowing portion of the thunderstorm complex and a small circulation on the leading edge. These features were reflected in the surface wind time histories and provided natural separation between various regions of the outflow. These features also contributed to the peak 1-s gust at all measurement stations. The turbulence characteristics of each outflow region were also investigated and compared. Reduced values of running turbulence intensity and elevated values of longitudinal integral scales were noted during the period of peak wind speed. Larger scales of turbulence within the outflow were also suggested via spectral analysis.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.158-163
• /
• 2011

Rigid polyurethane foam (PUF) was synthesized with different contents of aliphatic polyester polyol, aromatic polyester polyol and aliphatic polyether polyol to know change of properties under sea water. UTM(universal testing machine), DSC(differential scanning calorimetry), hardness meter and FT-IR(Fourier transform spectroscopy) were used to study the PUF`s physical properties under sea water. Compressive strength and hardness of PUF decreased with increasing the content of aromatic polyester polyol under sea water as aging. According to the results of IR spectral analysis, reduction of urethane and urea peak was found and allophanate and biuret peak increased. Although glass transition temperature of PUF increased, mechanical properties of PUF decreased under sea water, because PUF gets brittle when crosslink density increase.

• Publications of The Korean Astronomical Society
• /
• v.25 no.1
• /
• pp.15-21
• /
• 2010

We report results of image simulations of the KVN and VLBI experiments of the KVN with several other East Asia VLBI facilities. To investigate their imaging capability a model-generated image of 7 mm SiO maser emission in Mira variables is used. The resulting simulations show that the joint VLBI experiments of the KVN with East Asia VLBI facilities can produce reasonably good images at 7 mm spectral line experiments. However, there are no apparent differences in peak flux densities and images themselves in the simulations among different combinations of these facilities. In addition, the simulated images of observations which include bigger antennas do not show any expected improvement to the image sensitivity. The small variations in the peak flux density and similar image sensitivity, irrespective of different antenna sizes or numbers of baselines used in the simulations, turn out due to a specific characteristic of the adopted model image. Test simulations using another SiO maser image from R Cas observations prove that the participation of bigger antennas in the VLBI experiments does improve image sensitivity. We confirm the need of additional longer baselines in the experiments of the East Asia VLBI facilities to study very compact maser clumps on sub-milliarcsecond scales.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.4
• /
• pp.111-121
• /
• 1997

The spectral energy balance model is composed and the nonlinear interaction is approximated by the discrete interaction parameterization as in WAM model. The numerical results of durational limited growth test agree very well with those of the exact model, EXACT-NL. The response of a wave spectrum to a change in wind direction is investigated numerically for a sequence of direction changes 30$^{\circ}$ , 45$^{\circ}$ , 60$^{\circ}$ , 90$^{\circ}$ . The high frequency components relax more repidly to the new wind direction than the low frequency components and the relaxation process also depends on the wave age. For wind direction changes less than 60$^{\circ}$ , the coupling by nonlinear interaction is so strong that the secondary peak in input source distribution is counteracted by the negative lobe of the nonlinear interaction. For wind direction changes grater than 60$^{\circ}$ , a second independent wind-sea spectrum is generated in the new wind direction, while the old spectrum gradually decays as swell.

• Wind and Structures
• /
• v.11 no.6
• /
• pp.441-453
• /
• 2008

In this study, a partially earth-anchored cable system is studied in order to reduce the dynamic wind response of cable-stayed bridges. The employment of earth-anchored cables changes the dynamic characteristics of cable-stayed bridges under wind loads. In order to estimate the changes in the member forces, the spectral analysis for wind buffeting loads are performed and the peak responses are evaluated using 3-D finite element models of the three-span cable-stayed bridges with the partially earth-anchored cable system and with the self-anchored cable system, respectively. Comparing the results for the two different models, it is found that the earth-anchored cables affect longitudinal and vertical modes of the bridge. The changes of the natural frequencies for the longitudinal modes remarkably decrease the peak bending moment in the pylon and the movements at the expansion joints. The small changes of the natural frequencies for the vertical modes slightly increase bending moments and deflections in the girder. The original effects of the partially earth-anchored cable system are also shown under wind loads; the decrement of girder axial forces and bearing uplifting forces, and the increment of cable forces in the earth-anchored cables.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1637-1647
• /
• 2001

Multi-Code CDMA (MC-CDMA) can not only be integrated easily with a conventional system, but also achieve good spectral efficiency and high processing gain. However, it suffers from high value of peak-to-average power ratio (PAPR). In this paper, we propose the Multi-Phase CDMA (MP-CDMA) system that can provide variable rate service and is not susceptible to the non-linear characteristics of amplifier. The clipping is introduced between at the output of multi-code modulator and at the input of MPSK modulator in order to improve the performance of MPSK chip demodulator and reduce the system complexity, The system performances are compared for the different Number of codes and different clipping levels, respectively. The optimum clipping level is also evaluated for the different number of codes in both, AWGN and frequency flat fading channel.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.163-166
• /
• 2002

OFDM should be used for the fourth generation communication for high speed communication. Because of high spectral efficiency and high tolerance to fading channel, OFDM is applied to many high speed wire and wirless communication such as DAB(Digital Audio Broudcast), DVB(Digital Video Broadcast), IMT 2000 etc. Inter-modulation, however, is derived from PAR(Peak to Average Power Ratio) of OFDM signals. The paper describes PTS(Partial Transmit Sequence) and SLM(Select Mapping) of an existing methods which can reduce PAR. And then the document introduces the new method that is called "Combine PAR method". The method proposed in this paper is to combine PTS and SLM. As a result of the simulation, Combine PAR method is better than the existing methods.g methods.