• 비파괴검사학회지
• /
• 제19권5호
• /
• pp.363-368
• /
• 1999

시험체의 두께나 초음파 속도를 측정하기 위해서 초음파 펄스-에코법이 널리 사용되고 있다. 초음파 속도를 결정하기 위해서는 초음파 송수신 장치를 포함한 오실로스코우프와 같은 초음파 측정 장치를 사용하여 시험편에서의 초음파진행 시간을 측정하고, 초음파 진행 거리에 해당하는 시험편의 두께를 버어니어 캘리퍼스 또는 마이크로미터와 같은 길이측정 도구를 사용하여 측정한다. 그리고 초음파를 이용하여 시험편의 두께를 측정할 때에는 초음파 속도를 알고 있는 대비 시험편으로 기준을 설정하여야 한다. 본 연구에서는, 대비 시험편 없이 재료의 두께와 초음파 속도를 동시에 구하는 방법을 제시하였다. 재질과 두께를 달리한 여러 시험편에서 측정된 초음파 속도와 두께가 기존의 방법에 의해 측정한 값과 잘 일치하였다.

• 한국도로학회논문집
• /
• 제6권2호
• /
• pp.1-13
• /
• 2004

본 논문은 정하중하에서 김테스트를 사용하여 아스팔트 콘크리트의 소성변형과 변형강도가 공시체에 크기에 미치는 영향에 대해 연구하였다. 2가지 골재(편마암, 화강암)와 6가지 아스팔트를 사용하여 총14개의 밀입도 혼합물을 사용하였다. 마샬 배합설계를 통해 최적아스팔트 함량을 구하고 결정된 최적아스팔트 함량으로 마샬공시체 (S=10cm)와 자이레토리 공시체(S=15cm)를 제작하여 마샬안정도시험, 휠트래킹시험, 개발된 김테스트(Kim test)를 수행하였다. SAS 분석을 통하여 공시체의 지름이 김테스트의 결과에 중요한 변수가 아닌 것을 알았으나 공시체의 두께는 $K_D$에 주용한 변수가 되는 것을 알았다. $K_D$값에 y값이 사용되어 영향을 미치는 것으로 판단되었다. 공시체의 두께를 6.6cm 이상으로 제작하여 김테스트에 적용 할때에는 마샬안정도에서와 같이 y 값에 따른 보정계수를 사용하거나 시험시 6.6cm 미만으로 제작하여야 할 것이다. 향후 보정계수 사용에 관한 연구도 가능할 것으로 판단된다.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.1-19
• /
• 1998

After polymerizing composite resin with argon laser and visible light, four test, to be concretely, measurement of compressive strength using Instron testing machine, surface microhardness using Rockwell hardness tester, quantitative analysis of residual monomer using HPLC and analysis of degree of conversion using FTIR, were accomplished. Test groups were a sort of specimen with 3mm diameter, 4mm thickness for measuring compressive strength, two sort of specimen with 7mm diameter, 2mm and 3mm thickness for measuring surface microhardness, quantitative analysing of residual monomer after curing and measuring the degree of conversion, each were divided by six groups according to the condition of light exposure. In case of argon laser, in 1.0W and 0.5W output, the exposure time for specimen were 5 sec, 10 sec respectiyely. In case of visible light, the exposure time for specimen were 20 sec, 40 sec respectively. The test were accomplished and following results were obtained. 1. Compressive strength of composite resin was the highest in the group of 1 W output, exposing for 10 sec with argon laser, followed by the group of 0.5W, exposing for 10 sec with argon laser, the group of exposing for 40 sec with visible light. But there were statistically no significant difference between these three groups(p>0.05). 2. Surface microhardness of composite resin wasn't significantly affected by light curing conditions. 3. BIS-GMA within residual monomer was least detected in the group of exposing for 40 sec. TEGDMA was least detected in the group of 1 W output, exposing for 10 sec with argon laseboth 2mm and 3mm thickness specimen. 4. The degree of conversion of all groups in the 2mm thickness specimen were more than 50%, similar to each other but in the group of 1W, exposing 10 sec with argon laser the degree of conversion was highest in the 3mm thickness specimen. 5. Argon laser could make composite resin to has similar properties with 25% lesser exposure time than visible light.

• 폴리머
• /
• 제36권1호
• /
• pp.59-64
• /
• 2012

제품의 소형화와 경량화 추세에 따라 부품의 두께가 얇아지는 경향이 있다. 이러한 소형 및 경량 제품의 중요한 설계요소는 소재의 충격강도이다. 충격강도는 재료 고유의 물성값으로 기하학적 형상에 의존하지 않고 일정한 값을 가져야 한다. 그러나 충격강도 시험 시 시편의 두께에 따라 강도의 차이를 보이고 노치(notch)의 생성방법과 노치형상에 따라서도 민감도를 보인다. 본 연구에서는 시편의 두께와 노치형상 및 노치의 생성방법에 따른 충격강도를 알아보았다. 또한 노치의 각도와 노치에 대한 충격 방향에 따른 충격강도도 관찰하였다. 이를 위해 엔지니어링 플라스틱인 PC, ABS, 그리고 POM에 대하여 Izod 충격시험을 수행하였다. 그 결과 실험한 모든 수지에서 두께가 얇아질수록 충격강도가 높아지는 경향을 보였는데 PC수지가 가장 크게 증가하였다. PC수지는 두께가 두꺼울 때는 취성파괴를 보였는데 두께가 얇을 때는 연성파괴 양상을 보였다. 몰드노치 시편이 밀링노치 시편에 비해 충격강도가 높았고, 역방향 노치가 정방향 노치보다 충격강도가 높았다. 본 연구에서 실험한 수지 중에서 노치의 민감성은 PC가 가장 컸으며 다음이 POM, ABS순으로 나타났다.

• 소음진동
• /
• 제8권1호
• /
• pp.180-186
• /
• 1998

Vibration test fixture is used in random vibration control testing. The specified reference spectrum should be transmitted equally to the specimen attachment points on the fixture. In most practical cases, however, spectrum at each of specimen attachment points may be quite different from the specified reference spectrum because of the dynamic characteristics of vibration test fixture. This paper proposes the method of experimental dynamic modification of fixture system for vibration test so that the reference spectrum can be transmitted to the specimen attachment points without distortion. The stiffness of mounts of specimen and the thickness of fixture are considered as design variables. The frequency response functions of specimen used for input data are obtained from vibration testing, and the frequency response functions of fixture are obtained from finite element modeling. The sensitivities of frequency response functions at specimen attachment points to the mount stiffness are derived from synthesis method of transfer function. And the sensitivities to the thickness of fixture are also derived from finite element modeling. The presented method is verified by computer simulation and vibration testing.

• Journal of the Korean Wood Science and Technology
• /
• 제26권4호
• /
• pp.26-33
• /
• 1998

Acoustical properties of chestnut and paulownia woods have been determined in four film thicknesses of oriental lacquering and cashew varnishing on double surfaces of soundboard to elucidate effects of finishing. Accelerometer was attached to the specimen at one third position from one end, and specimen was hit by the impact hammer at one third position from opposite end. Data were processed by vibration analyzer. The ratio of axial-to-transverse sound velocity of untreated specimens of chestnut and paulownia were 3.25 and 5.34, respectively. Natural frequency, specific Young's modulus, acoustical coefficient, sound velocity, damping of sound radiation(DSR) and acoustical converting efficiency(ACE) decreased by oriental lacquering and cashew varnishing for both species. Damping of internal friction of chestnut decreased by oriental lacquering and cashew varnishing, but that of paulownia increased. Natural frequency. specific Young's modulus, acoustical coefficient, sound velocity, and DSR decreased with increased film thickness of both finishing materials. However, damping of internal friction and ACE showed irregular tendency with increased film thickness. Acoustical properties of cashew varnished chestnut specimen were better than those of oriental lacquered specimen. Acoustical properties of oriental lacquered paulownia specimen were better than those of cashew varnished specimen.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.451-462
• /
• 1995

Single overload tests performed to examine the crack retardation behavior for the specimen thickness and overload ratios. Delayed crack length was tend to increase in small thickness and big overload ratio but was difference between delayed crack length and plastic zone size that expected in specimen thickness. So retardation behavior that estimated in plastic zone size, was not sufficient. Crack tip branching and striation distribution, secondary mechanisms that effected in retardation behavior, was examined by experiment and finite element analysis. Crack tip branching was affected by micro structure, and appeared the more complicatedly according to increasing damage by overload and decreasing crack driving force in base line stress level. And crack tip branching the branching angle decreased crack driving force in the crack tip. And a characteristic of the fractography on retardation zone was that striation distribution did not appear due to decreased crack driving force.

• Geomechanics and Engineering
• /
• 제19권2호
• /
• pp.193-199
• /
• 2019

A frozen fringe plays a key role in frost heave development in soils. Previous studies have focused on the physical and mechanical properties of the frozen fringe, such as overall hydraulic conductivity, water content and pore pressure. It has been proposed that the thickness of the frozen fringe controls frost heave behavior, but this effect has not been thoroughly evaluated. This study used a temperature-controllable cell to investigate the impact of frozen fringe thickness on the characteristics of frost heave. A series of laboratory tests was performed with various temperature boundary conditions and specimen heights, revealing that: (1) the amount and rate of development of frost heave are dependent on the frozen fringe thickness; (2) the thicker the frozen fringe, the thinner the resulting ice lens; and (3) care must be taken when using the frost heave ratio to characterize frost heave and evaluate frost susceptibility because the frost heave ratio is not a normalized factor but a specimen height-dependent factor.

• 대한치과기공학회지
• /
• 제43권1호
• /
• pp.1-5
• /
• 2021

Purpose: To perform a comparative study on curing shrinkage according to the thickness of photopolymerization resin. Methods: Stainless steel molds of 2, 4, and 6 mm heights were prepared. The 2, 4, and 6 mm-height molds were classified as the 2H, 4H, and 6H groups, respectively. A photopolymerization resin was injected into the stainless steel mold. Photopolymerization was carried out using a photopolymer machine. During photopolymerization, the wavelength and intensity of 400~405 nm were set to 10, the highest intensity among 1~10. Photopolymerization was performed for 30 min per specimen (each group=10). The inner and outer areas of the specimen were measured. The data were analyzed using one-way ANOVA and Kruskal-Wallis H test (α=0.05). Results: In terms of the inner and outer diameters of the photopolymerization resin specimen, the 2H group contracted the most, whereas the 6H group contracted the least. A statistically significant difference was found between the groups (p<0.05). Conclusion: The amount of light irradiation of the photopolymerization resin must be adjusted according to the thickness.

• 한국세라믹학회지
• /
• 제28권8호
• /
• pp.619-625
• /
• 1991

The current-voltage characteristics of the semiconducting BaTiO3 ceramics are measured in the range of 0.01∼100 Volt. Non ohmic behavior was observed above Tc. This behavior is not dependent on specimen thickness and is not observed at the incomplete semiconducting sepcimen. From this experiment, non-ohmic behavior of PTC is attributed to Heywang's potential barrier not to space change limited current. In the low voltage range, current-voltage characteristics of PTC ceramics can be explained by Heywang model.