• 한국표면공학회지
• /
• 제37권2호
• /
• pp.128-136
• /
• 2004

Effects of alloying elements on the surface characteristics of Fe-38Al intermetallic compounds were investigated using potentiostat. The specimens were casted by the vacuum arc melting. The subsequent homogenization and the stabilization led to the homogeneous DO$_3$ structure of the specimen. After the corrosion tests, the surface of the tested specimen was observed by the optical microscopy and scanning electron microscopy(SEM). For Fe-38 at.% Al intermetallic compound, the addition of Cr and Mo proved to be beneficial in decreasing the grain boundary attack by decreasing the active current density. Addition of Band Nb resulted in a higher active current density and also a higher passive current density. These results indicated the role of Cr and Mo in improving the pitting corrosion resistance of Fe-38 at.%Al intermetallic compound. Band Nb addition to Fe-38 at.%Al accelerated the granular corrosion. Fe-38 at.%Al containing Cr and Mo showed remarkably improved pitting corrosion resistance in comparison with Band Nb addition to Fe-38 at. %Al.

• 한국세라믹학회지
• /
• 제31권11호
• /
• pp.1299-1306
• /
• 1994

Effect of MgO content on microstructural evolution and microwave dielectric properties of Ba(Mg1/3Ta2/3)O3 system was investigated. MgO content was varied from 10 mol% deficiency to 10 mol% excess of stoichiometric composition, respectively. It was found that MgO-deficient specimen showed faster grain growth rate than stoichometric and MgO excess BMT system. Besides, sandwich type precipitates of Ba5Ta4O15 which was formed within the BMT grain, might lead to the anisotropic grain growth of BMT grain. On the contrary, in MgO excess specimen, BMT grain growth rate was retarded by precipitations of MgO phase in grain boundary. Besides, the Q values of MgO-deficient showed lower than MgO-excess due to precipitations of Ba5Ta4O15 within BMT grain.

• 한국레이저가공학회지
• /
• 제2권1호
• /
• pp.16-21
• /
• 1999

The surface of Alloy 600 was alloyed using a continuous wave $CO_2$ laser beam in order to improve its corrosion resistance. Laser surface alloying (LSA) was done by melting the surface electroplated with Cr of the alloy. The Cr concentration of the alloyed surface was 28-30 at.%, which is similar to that of Alloy 690. Alloying elements in the alloyed layer was observed to be distributed very homogeneously all over the alloyed region. According to the electrochemical and modified Huey tests, the corrosion resistance, in particular the grain boundary corrosion resistance, of the LSA specimens was significantly improved, compared with that of the as-received(AR) specimen. This improved corrosion resistance of the alloyed specimen might be attributed to the high Cr content which could make possible formation of more stable and dense passive film onto its surface.

• 비파괴검사학회지
• /
• 제32권4호
• /
• pp.355-361
• /
• 2012

This paper presents an experimental study on the detection and location of nonlinear scattering source due to the presence of fatigue crack in a laboratory specimen. The proposed technique is based on a combination of nonlinear elastic wave spectroscopy(NEWS) and time reversal(TR) focusing approach. In order to focus on the nonlinear scattering position due to the fatigue crack, we employed only one transmitting transducer and one receiving transducer, taking advantage of long duration of reception signal that includes multiple linear scattering such as mode conversion and boundary reflections. NEWS technique was then used as a pre-treatment of TR for spatial focusing of reemitted second harmonic signal. The robustness of this approach was demonstrated on a cracked specimen and the nonlinear TR focusing behavior is observed on the crack interface from which the second harmonic signal was originated.

• Computers and Concrete
• /
• 제20권1호
• /
• pp.57-63
• /
• 2017

A coupled experimental-numerical study on shear fracture in concrete specimens with different geometries is carried out. The crack initiation, propagation and final breakage of concrete specimens are experimentally studied under compression loading. The load-strain and the strength of the specimens are experimentally measured, indicating decreasing effects of the shear behavior on the failure load of the specimen. The effects of specimen geometries on the shear fracturing path in the concrete specimens are also investigate. Numerical models using an indirect boundary element method are made to evaluate the crack propagation paths of concrete specimens. These numerical results are compared with the performed experiments and are validated experimentally.

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.113-118
• /
• 1999

In order to evaluate strength of spot welded joint, at first it is importent that we should know strain distribution near nugget zone. During loading, in HAZ, compressive strain increase with Increase of load, but in nugget zone tensile strain increase. During unloading, on the other hand, even through the decreases, the strain variation is not almost appeared in nugget zone and HAZ. In nugget boundary zone, the strain range increases continuously along with load increase on outer surface, but the strain increases continunously and decreases rapidly beyond yield strength on inner surface. In this paper, strain distribution are measured in inner and outer surface with variation of thickness and load under tensile-shear load. Tensile-shear strength increased as with increase of specimen thickness. As for thickness increase rates are 25%, 50%, 100%, and 150%, tensile-shear strength in crease rates are 40%, 81%, 130% and 228%.

• 한국분말재료학회지
• /
• 제23권3호
• /
• pp.247-253
• /
• 2016

In this study, solid solution heat treatment of consolidated nickel-based superalloy powders is carried out by hot isotactic pressing. The effects of the cooling rate of salt quenching, and air cooling on the microstructures and the mechanical properties of the specimens are analyzed. The specimen that is air cooled shows the formation of serrated grain boundaries due to their obstruction by the carbide particles. Moreover, the specimen that is salt quenched shows higher strength than the one that is air cooled due to the presence of fine and close-packed tertiary gamma prime phase. The tensile elongation at high temperatures improves due to the presence of grain boundary serrations in the specimen that is air cooled. On the contrary, the specimen that is salt quenched and consists of unserrated grain boundaries shows better creep properties than the air cooled specimen with the serrated grain boundaries, due to the negative creep phenomenon.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 춘계학술대회
• /
• pp.35-38
• /
• 1997

The interfacial bonding energy between laser surface treated HA layer and Ti alloy substrate was investigated using a mechanical push-out tester. The initial slope of shear-stress and reduced displacement curves, maximum interfacial bond strength and bonding energy were calculated from results of the push-out test. The calculated initial slpoes are 38 MPa for the Ti alloy(A), 65 MPa for the sandblast finished specimen(B), 95 MPa for the HA plasma spray coated specimen and 49 MPa for the laser surface treated specimen(D). The maximum interfacial bonding strength are 3 MPa for the A, 19 MPa for the B, 20 MPa for the C, 10 MPa for the D. The interfacial bonding energies are $3.3\times10^{-9}J/mm^2$ for the A, $15.5\times10^{-9}J/mm^2$ for the B, $15.6\times10^{-9}J/mm^2$ for the C and $18.3\times10^{-9}J/mm^2$ for the D. Microscopic observation shows that the breaking of the laser treated specimen had been occured through the boundary between HA layer and polymer resin, but the untreated specimen had been occured through the inside of HA coating layer.

• 방사성폐기물학회지
• /
• 제3권4호
• /
• pp.301-307
• /
• 2005

조사후 핵연료 가열(PIA장비)를 이용한 고연소도 UO2 사용후 핵연료의 산화 및 가열후 미세조직의 변화를 관찰하였다. 울진 2호기에서 한국원자력연구소 조사후시험시설로 이송된 국산 경수로용 고연소도 사용후 핵연료는 봉평균 연소도가 57,000 MWd/tU-rod avg.이였다. 본 시험에 사용된 시편은 국부연소도 65,000 MWd/tU UO2 소결체의 고형체 200 mg을 사용하였다. 본 시편을 사용후 핵 연료 가열(PIA) 시험장비를 이용하여 핫셀 내에서 3시간의 산화시험과 연속적으로 $1,400^{\circ}C$ 까지 가열하였다. 결정립경계까지의 산화를 위하여 $500^{\circ}C$에서 헬륨 50 ml, 표준공기 100 ml를 흔합한 산화분위기로 3시간을 유지하였다. 핵분열기체 방출거동을 알기위해 시험 전과정중에 85Kr의 방출량을 베타 측정기와 감마 측정기를 이용하여 실시간으로 측정 하였다. 가열시험이 종료된 후 전자주사현미경을 이용하여 미세구조의 변화를 관찰하였다. 시험결과 가열하는 동안 핵분열생성물은 UO2기지의 결정립경계와 표면으로 이동된 것을 관찰하였다. 이 시편은 환원과정을 통하여 재구조화 되었고, $5\~10\;{\mu}m$ 정도의 결정립크기를 가진 것으로 나타났다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.290-297
• /
• 2000

A new form of construction utilizing structural steel as the boundary elements in ductile flexural concrete walls is proposed to solve the bar congestion problems associated with such a heavily reinforced region. Two wall specimens containing rectangular hollow structural sections(HSS) and channels at their ends respectively were constructed rectangular hollow structural sections(HSS) and channels ar their ends respectively were constructed and tested under reversed cyclic loading to evaluate the construction process as well as the structural performance. One companion standard reinforced concrete wall specimen was also tested for the comparison purpose At an Initial stage all three specimens were carefully detailed to have the approximately same flexural capacity. Analysis and comparison of test results indicated that the reversed cyclic responses of the three walls showed similar hysteretic properties but in those with steel boundaries local bucking of the corresponding steel elements following significant yielding of structural steel was prominent. Design procedures considering local instability of the structural steel elements and the interaction between steel chord and concrete web members in such composite walls are presented.