• 전자공학회논문지SC
• /
• 제44권1호
• /
• pp.67-73
• /
• 2007

본 연구에서는 특정 자동차에 대한 Charging 시스템의 적합성 여부를 판별할 수 있는 충방전 Balance 시뮬레이터의 Prototype을 개발 하였다. 차량운전 환경요건에 따른 운전 패턴 등, 시뮬레이터의 구성을 위해 각종 전기부하와 이와 관련된 배터리 모델링을 하였고 실차실험을 행하여 그 데이터를 분석 정리하였다. 제안하는 모델과 분석된 데이터를 바탕으로 충방전 시뮬레이터를 개발하였고, 개발된 시뮬레이터는 정해진 차종으로 임의의 주행환경으로 운전할 때 차량의 전기에너지 공급 문제를 실차실험을 한 것과 같이 분석할 수 있다

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2000년도 전지기술심포지움
• /
• pp.51-62
• /
• 2000

Large plastic Li-ion (PLI) cells (25 to 28-Ah) were fabricated for an EV application. The 28-Ah cells showed high specific energy (160 Wh/kg), high specific power (526 W/g), excellent round-trip energy efficiency $(92\%)$, and low self-discharge rate ($6\%$ in 30 days). A 25-Ah cell of an earlier design showed good cycle life of up to 750 cycles at $100\%$ DOD to $80\%$ of its initial capacity, while cycle life test of a 28-Ah cell of a later design is in progress. Preliminary safety tests were also carried out using 6-Ah cells of a similar electrode design giving very encouraging results for development of a safe hish-energy density PLI battery for EV application.

• 대한환경공학회지
• /
• 제39권12호
• /
• pp.714-722
• /
• 2017

수질오염총량관리제도(이하 총량제)는 하천의 목표수질을 달성하기 위해 유역에서 배출되는 오염물질의 총량을 관리하는 제도이다. 유역에서 배출되는 오염물질의 허용총량은 수질모델을 활용하여 산정하며, 이과정에서 오염부하량은 발생, 배출, 유달부하량으로 구분할 수 있다. 유달부하량은 배출부하량과 유달율의 곱으로 계산되며 유달율은 유역에서 배출된 오염물질이 하천의 특정지점에 도달하는 비율로 정의된다. 본 연구에서는 Hwang(2016) 등이 제시한 기준유량 조건의 유달율 추정방법을 영강유역에 적용하고 QUALKO2 수질모델의 수질 입력자료를 생성하여 기준유량 조건의 유달율 산정방법(식 (3))과 평균 개념의 유달율 산정 방법(식 (2))의 비교분석을 통해 유달율 추정방법에 대한 검증 연구를 수행하였다. 연구결과, 유달율 함수식은 식 (2)와 식 (3) 모두 사용 가능하나, 배출계수 적용에 따라 방법론을 달리할 필요가 있다. 식 (2)를 사용할 경우는 배출계수를 저수량, 평수량 구분없이 1로 동일하게 사용해야 하며, 식 (3)을 사용할 경우는 기술지침에서 정한 배출계수(저수량 0.15, 평수량 0.5)를 적용해야 할 것으로 판단된다.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권4호
• /
• pp.317-324
• /
• 1994

In this study, new preparation method of LiCoO$_{2}$ was applied to develop cathode active material for Li rechargeable cell, and followed by X-ray diffraction analysis, electrochemical properties and initial charge/discharge characteristics as function of current density. HC8A72- and CC9A24-LiCoO$_{2}$ were prepared by heating treatment of the mixture of LiOH H$_{2}$O/CoCO$_{3}$(1:1 mole ratio) and the mixture of Li$_{2}$CO$_{3}$/CoCO$_{3}$(1:2 mole ratio) at 850 and 900.deg. C, respectively. Two prepared LiCoO$_{2}$s were identified as same structure by X-ray diffraction analysis. a and c lattice constant were 2.816.angs. and 14.046.angs., respectively. The electrochemical potential of CFM-LiCoO$_{2}$(Cyprus Foote Mineral Co.'s product), HC8A72-LiCoO$_{2}$ and CC9A24 LiCoO$_{2}$ electrode were approximately between 3.32V and 3.42V vs. Li/Li reference electrode. Stable cycling behavior was obtained during the cyclic voltammetry of LiCoO$_{2}$ electrode. According as scan rate increases, cathodic capacity decreases, but redox coulombic efficiency was about 100% at potential range between 3.6V and 4.2V vs. Li/Li reference electrode. Cathodic capacity of HC8A72-LiCoO$_{2}$ was 32% higher than that of CFM-LiCoO$_{2}$ and that of CC9A24-LiCoO$_{2}$ was 47% lower than that of CFM-LiCoO$_{2}$ at 130th cycle in the condition of lmV/sec scan rate. Constant cur-rent charge/discharge characteristics of LiCoO$_{2}$/Li cell showed increasing Ah efficiency with initial charge/discharge cycle. Specific discharge capacities of CFM and HC8A72-LiCoO$_{2}$ cathode active materials were about 93mAh/g correspondent to 34% of theretical value, 110mAh/g correspondent to 40% of theretical value, respectively. In the view of reversibility, HC8A72-LiCoO$_{2}$ was also more excellent than CFM- and CC9A24-LiCoO$_{2}$.

• 청정기술
• /
• 제22권4호
• /
• pp.308-315
• /
• 2016

수명특성이 우수한 실리콘 음극재를 제조하기 위해 졸겔법을 통해 $SiO_x/ZnO$ 복합체를 제조하였고, 제조된 복합체는 PVC를 탄소 전구체로 하여 탄소를 피복하였다. 복합체에 포함된 ZnO를 HCl로 제거하여 내부에 빈 공간을 만들어 충 방전에 따른 실리콘의 부피변화를 완화할 수 있게 하였다. 합성된 복합체의 결정구조와 형상을 파악하기 위해 XRD, SEM, TEM 분석을 실시하였다. 탄소 피복된 복합체에 포함된 탄소함량을 TGA를 통해 알아보았으며, 복합체의 기공구조를 확인하기 위해 BET 비표면적 분석과 BJH 기공분포를 확인하였다. 탄소의 추가로 향상된 전기전도성을 측정하였으며, 전기화학적 특성은 AC 임피던스 측정과 충 방전 및 수명특성을 확인하였다. $SiO_x/ZnO$시료에 탄소를 피복할 경우에 전기전도도가 증가하였으며, 방전용량도 증가하였다. 염산으로 ZnO를 제거한 시료의 경우에 표면적은 증가하였으나, 전지의 방전용량은 오히려 감소하였다. 탄소를 피복하지 않은 $SiO_x/ZnO$ 시료의 경우에 방전용량이 매우 낮았으며, 탄소를 피복한 후의 시료는 높은 충방전용량을 나타내었다. 수명특성의 경우, $C-SiO_x/ZnO$ 복합체(Zn : Si : C = 1 : 1 : 8)가 0.2 C의 전류량에서 50 사이클에서 $815mAh\;g^{-1}$의 용량으로 기존 흑연계 음극재보다 높은 용량을 나타내었다.

• 한국전기전자재료학회논문지
• /
• 제32권2호
• /
• pp.165-173
• /
• 2019

Lithium anodes (13, 15, 17, and 20 wt% Li) were fabricated by mixing molten lithium and iron powder, which was used as a binder to hold the molten lithium, at about $500^{\circ}C$ (discharge temp.). In this study, the effect of applied pressure and lithium content on the discharge properties of a thermal battery's single cell was investigated. A single cell using a Li anode with a lithium content of less than 15 wt% presented reliable performance without any abrupt voltage drop resulting from molten lithium leakage under an applied pressure of less than $6kgf/cm^2$. Furthermore, it was confirmed that even when the solid electrolyte is thinner, the Li anode of the single cell normally discharges well without a deterioration in performance. The Li anode of the single cell presented a significantly improved open-circuit voltage of 2.06 V, compared to that of a Li-Si anode (1.93 V). The cut-off voltage and specific capacity were 1.83 V and $1,380As\;g^{-1}$ (Li anode), and 1.72 V and $1,364As\;g^{-1}$ (Li-Si anode). Additionally, the Li anode exhibited a stable and flat discharge curve until 1.83 V because of the absence of phase change phenomena of Li metal and a subsequent rapid voltage drop below 1.83 V due to the complete depletion of Li at the end state of discharge. On the other hand, the voltage of the Li-Si anode cell decreased in steps, $1.93V{\rightarrow}1.72V(Li_{13}Si_4{\rightarrow}Li_7Si_3){\rightarrow}1.65V(Li_7Si_3{\rightarrow}Li_{12}Si_7)$, according to the Li-Si phase changes during the discharge reaction. The energy density of the Li anode cell was $807.1Wh\;l^{-1}$, which was about 50% higher than that of the Li-Si cell ($522.2Wh\;l^{-1}$).

• 공업화학
• /
• 제10권6호
• /
• pp.822-827
• /
• 1999

본 연구에서는 에너지 밀도가 큰 초고용량 캐패시터를 제작하기 위한 기초 연구로서 활성탄소섬유의 물성과 유기 전해질의 특성이 초고용량 캐패시터의 전기화학적 특성에 미치는 영향을 조사하였다. 유기성 전해질의 경우는 이온의 크기가 수용성 전해질 보다 훨씬 크기 때문에 탄소전극의 세공크기에 많은 영향을 받으며, 용량을 발현할 수 있는 유효세공의 크기가 커야 한다는 것을 알 수 있었다. 혼합용매를 이용한 전해액의 조성은 큰 비축전용량과 빠른 충전속도, 그리고 낮은 ESR 및 방전전류의 세기에 대한 높은 비축전용량 유지성 등의 우수한 충방전 특성을 나타내는 것을 알 수 있었고, 전해질의 높은 이온전도도가 용량발현 및 자가방전 특성에 큰기여를 하고 있으며, 전해질 이온의 크기는 충전속도에 많은 영향을 미치는 것을 알 수 있었다.

• Carbon letters
• /
• 제16권2호
• /
• pp.78-85
• /
• 2015

Activated carbons (ACs) were prepared by activation of coal tar pitch (CTP) in the range of $700^{\circ}C-1000^{\circ}C$ for 1-4 h using potassium hydroxide (KOH) powder as the activation agent. The optimal activation conditions were determined to be a CTP/KOH ratio of 1:4, activation temperature of $900^{\circ}C$, and activation time of 3 h. The obtained ACs showed increased pore size distribution in the range of 1 to 2 nm and the highest specific capacitance of 122 F/g in a two-electrode system with an organic electrolyte, as measured by a charge-discharge method in the voltage range of 0-2.7 V. In order to improve the performance of the electric double-layer capacitor electrode, various mixtures of CTP and petroleum pitch (PP) were activated at the optimal activation conditions previously determined for CTP. Although the specific capacitance of AC electrodes prepared from CTP only and the mixtures of CTP and PP was not significantly different at a current density of 1 A/g, the AC electrodes from CTP and PP mixtures showed outstanding specific capacitance at higher current rates. In particular, CTP-PP61 (6:1 mixture) had the highest specific capacitance of 132 F/g, and the specific capacitance remained above 90% at a high current density of 3 A/g. It was found that the high specific capacitance could be attributed to the increased micro-pore volume of ACs with pore sizes from 1 to 2 nm, and the high power density could be attributed to the increased meso-pore volume.

• 가정간호학회지
• /
• 제7권1호
• /
• pp.58-72
• /
• 2000

This study was an attempt to encourage the development of a rehabilitation delivery system and programs as a substitute service for hospitalization on the case of car accident patients, such as hospital based home health care nursing services. Various substitute services for hospitalization are required to curtail the length of stay for inpatients who were hospitalized with car accident compensation insurance. It focused on developing an estimation an early discharge day for car accident inpatients based on detailed statements of treatment for 111 inpatients who were hospitalized at the General Hospital in 1997. This study had four specific purposes as follows. First. to find out the utilization of medical services. Second, to estimate the time of early discharge and income increasing effect based on early discharge for those patients. Third, to identify the factors affecting total medical expenditure and the length of stay for those inpatients. Forth, to figure out the need of utilizing home health care nursing service for accident patients. In order to analyze the length of stay and medical expenditure for inpatients who were hospitalized due to car accidents, the authors conducted micro- and macro-analysis of medical and medical expenditure records. Micro-analysis was done by nominal group discussion of 4 expertise with the critical criteria, such as a decrease in the amount of treatment after surgery, treatments, tests, drugs and changes in the test consistency, drug methods, vital signs, start of ROM exercise, doctor's order, patient's outside visiting ability, and stable conditions. In addition to identifying variables affecting medical expenditure, and the length of stay and income effect due to early discharge day, the data was analyzed with a multiple regression analysis and linear regression analysis model by SPSS-PC for windows and Excell program. Results of this study were as follows. First. the mean length of stay was 50.3 days. whereas the mean length of stay due to early discharge was 34.3 days at the hospital. The estimation of time of early discharge depended on the length of stay. The longer the length of stay, the longer the length of time of early discharge : for instance a length of stay under 10 days was estimated as correlating to a mean length of stay of 6.6 days and early discharge of 6.5. The mean length of stay was 217.4 days and the time of early discharge was 110.1 respectively. The mean medical expenditure per day was found to be 169.085 Won and the mean medical expenditure per day showed negative linear trends according to the length of stay at the hospital. The estimation results of the income effect due to being discharged 16 days early was around 2,244,000 won per bed. However. this sum does not represent the real benefits resulting from early discharge, but rather the income increasing amount without considering medical prime cost in the general hospital. Therefore, further analysis is required on the cost containments and benefits as turn over rate per bed as the medical prime costs. The length of stay was most significant and was positive to the total medical expenditure, as expected. Surgery and patient's residential area was also an important variable in explaining medical expenditure. The level of complications was the most significant variable in explaining the length of stay. There was a high level for need a home health care nursing service which further supports early discharge for accident patients. In addition, when the patient was discharged. they needed follow up care for complications suffered during the car accident. $86.8\%$ of discharged patients responded that they needed home health services after early discharge. From these research findings, the following suggestions have been drawn. Strategies on a health care delivery system must be developed in order to focus on the consumer's needs and being planned for 21 century health policy in Korea. Community based intermediate facilities or home health care should be developed for rehabilitation services as a substitute for hospitalization in order to shorten the length of stay would be. A hospital based home health care nursing service. it would be available immediately to utilize by patients who want rehabilitation services as a substitute for hospitalization with the cooperation of car insurance companies.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.94.2-94.2
• /
• 2011

In this work, multi-functional groups, i.e., nitrogen and oxygen, contained microporous carbons (MF-MCs) were prepared by the one step carbonization of the poly(vinylidene chloride-co-acrylonitrile-co-methyl methacryalte) (PVDC-AN-MMA) without activation. The electrochemical performance of MF-MCs was investigated as a function of carbonization temperature. It was found that MF-MCs had a high specific surface area over $800m^2/g$ without additional activation, resulting from the micropore's formation by the release of chlorine groups. In addition, although functional groups decreased, specific surface area was increased with increasing carbonization temperature, leading to the enhanced electrochemical performance. The pore size of the carbon distributed mainly in small micropore of 1.5 to 2 nm, which was idal for aqueous electrolyte. Indeed, the unique microstructure features, i.e. high specific surface area and optimized pore size provided high energy storage capability of MF-MCs. These results indicated that the microporous features of MF-MCs lead to feasible electron transfer during charge/discharge duration and the presence of nitrogen and oxygen groups on the MF-MCs electrode led to a pseudocapacitive reaction.