• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.1
• /
• pp.67-73
• /
• 2007

Prototype of an electric charge/discharge balance simulator was developed for evaluation of matching charging/discharging balance between real system and simulation results for specific vehicle in this research. Battery modeling and other electric modeling were done and real car experiments were performed. Then, We developed a balance simulator on the basis of proposed model and experiment results. Also, we can analyze charging/discharging balance for specific new car as real experiments.

• 한국전기화학회:학술대회논문집
• /
• 2000.12a
• /
• pp.51-62
• /
• 2000

Large plastic Li-ion (PLI) cells (25 to 28-Ah) were fabricated for an EV application. The 28-Ah cells showed high specific energy (160 Wh/kg), high specific power (526 W/g), excellent round-trip energy efficiency $(92\%)$, and low self-discharge rate ($6\%$ in 30 days). A 25-Ah cell of an earlier design showed good cycle life of up to 750 cycles at $100\%$ DOD to $80\%$ of its initial capacity, while cycle life test of a 28-Ah cell of a later design is in progress. Preliminary safety tests were also carried out using 6-Ah cells of a similar electrode design giving very encouraging results for development of a safe hish-energy density PLI battery for EV application.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.12
• /
• pp.714-722
• /
• 2017

The TPLMs is a system to manage the total amount of pollutants discharged from the watershed in order to achieve the target water quality of the river. In this process, the pollutant load can be classified into generation, discharge and delivery load. When using equation 2, the discharge coefficient should be 1. In case of using equation 3, it is considered that the discharge coefficient defined in the Technical Guideline should be applied. The delivery load is calculated as the product of the discharge load and the delivery ratio, and the delivery ratio is defined as the rate at which the pollutant discharged from the watershed reaches a specific point in the stream. In this study, the delivery ratio estimation method proposed by Hwang (2016) was applied to the Yonggang watershed in the Nakdong river. And the input data of QUALKO2 model was generated by using the estimated delivery ratio (equation 3) and the validation study was conducted by comparing with DRave (equation 2). As a result of the study, it is possible to use both the equation 2 and the equation 3, but it is necessary to change the methodology according to the application of the discharge coefficient.

• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.317-324
• /
• 1994

In this study, new preparation method of LiCoO$_{2}$ was applied to develop cathode active material for Li rechargeable cell, and followed by X-ray diffraction analysis, electrochemical properties and initial charge/discharge characteristics as function of current density. HC8A72- and CC9A24-LiCoO$_{2}$ were prepared by heating treatment of the mixture of LiOH H$_{2}$O/CoCO$_{3}$(1:1 mole ratio) and the mixture of Li$_{2}$CO$_{3}$/CoCO$_{3}$(1:2 mole ratio) at 850 and 900.deg. C, respectively. Two prepared LiCoO$_{2}$s were identified as same structure by X-ray diffraction analysis. a and c lattice constant were 2.816.angs. and 14.046.angs., respectively. The electrochemical potential of CFM-LiCoO$_{2}$(Cyprus Foote Mineral Co.'s product), HC8A72-LiCoO$_{2}$ and CC9A24 LiCoO$_{2}$ electrode were approximately between 3.32V and 3.42V vs. Li/Li reference electrode. Stable cycling behavior was obtained during the cyclic voltammetry of LiCoO$_{2}$ electrode. According as scan rate increases, cathodic capacity decreases, but redox coulombic efficiency was about 100% at potential range between 3.6V and 4.2V vs. Li/Li reference electrode. Cathodic capacity of HC8A72-LiCoO$_{2}$ was 32% higher than that of CFM-LiCoO$_{2}$ and that of CC9A24-LiCoO$_{2}$ was 47% lower than that of CFM-LiCoO$_{2}$ at 130th cycle in the condition of lmV/sec scan rate. Constant cur-rent charge/discharge characteristics of LiCoO$_{2}$/Li cell showed increasing Ah efficiency with initial charge/discharge cycle. Specific discharge capacities of CFM and HC8A72-LiCoO$_{2}$ cathode active materials were about 93mAh/g correspondent to 34% of theretical value, 110mAh/g correspondent to 40% of theretical value, respectively. In the view of reversibility, HC8A72-LiCoO$_{2}$ was also more excellent than CFM- and CC9A24-LiCoO$_{2}$.

• Clean Technology
• /
• v.22 no.4
• /
• pp.308-315
• /
• 2016

$SiO_x/ZnO$ composites were prepared from sol-gel method for excellent cycle life characteristics. The composites were coated by PVC as a carbon precursor. ZnO removal to create a void space therein was able to buffer the volume change during charge and discharge. To determine the crystal structure and the shape of the synthesized composite, XRD, SEM, TEM analysis was performed. The carbon contents in the composites were confirmed by TGA. The pore structure and pore size distribution of the composite was measured with the BET specific surface area analysis and BJH pore size distribution. Enhanced electric conductivity by carbon addition was determined from powder resistance measurement. Electrochemical properties were measured with the AC impedance and the charge and discharge cycle life characteristics. When carbon was coated on the $SiO_x/ZnO$ sample, the electrical conductivity and the discharge capacity were increased. After removal of ZnO with HCl the surface area of the sample was increased, but the discharge capacity was decreased. $SiO_x/ZnO$ sample without acarbon coating showed very low discharge capacity, and after carbon coating the sample showed high discharge capacity. For cycle life characteristics, $C-SiO_x/ZnO$ composite (Zn : Si : C = 1 : 1 : 8) with a capacity of $815mAh\;g^{-1}$ at 50 cycle and 0.2 C has higher capacity than existing graphite-based anode materials.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.2
• /
• pp.165-173
• /
• 2019

Lithium anodes (13, 15, 17, and 20 wt% Li) were fabricated by mixing molten lithium and iron powder, which was used as a binder to hold the molten lithium, at about $500^{\circ}C$ (discharge temp.). In this study, the effect of applied pressure and lithium content on the discharge properties of a thermal battery's single cell was investigated. A single cell using a Li anode with a lithium content of less than 15 wt% presented reliable performance without any abrupt voltage drop resulting from molten lithium leakage under an applied pressure of less than $6kgf/cm^2$. Furthermore, it was confirmed that even when the solid electrolyte is thinner, the Li anode of the single cell normally discharges well without a deterioration in performance. The Li anode of the single cell presented a significantly improved open-circuit voltage of 2.06 V, compared to that of a Li-Si anode (1.93 V). The cut-off voltage and specific capacity were 1.83 V and $1,380As\;g^{-1}$ (Li anode), and 1.72 V and $1,364As\;g^{-1}$ (Li-Si anode). Additionally, the Li anode exhibited a stable and flat discharge curve until 1.83 V because of the absence of phase change phenomena of Li metal and a subsequent rapid voltage drop below 1.83 V due to the complete depletion of Li at the end state of discharge. On the other hand, the voltage of the Li-Si anode cell decreased in steps, $1.93V{\rightarrow}1.72V(Li_{13}Si_4{\rightarrow}Li_7Si_3){\rightarrow}1.65V(Li_7Si_3{\rightarrow}Li_{12}Si_7)$, according to the Li-Si phase changes during the discharge reaction. The energy density of the Li anode cell was $807.1Wh\;l^{-1}$, which was about 50% higher than that of the Li-Si cell ($522.2Wh\;l^{-1}$).

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.822-827
• /
• 1999

The specific capacitance characteristics which were of the electric double layer capacitors(ELDC) made of phenol based activated carbon fiber(ACF) electrodes and organic electrolytes has been investigated with respect to different specific surface area of electrodes and different kinds of organic electrolytes. Throughout charge-discharge cell tests, it has been found that larger surface area and larger pore diameter of electrodes contribute to increase the specific capacitance. Binary mixture of organic solvent with propylene cabonate(PC) and tetrahydrofuran(THF) for 1 M-$LiClO_4$ electrolyte has a higher specific capacitance than single solvent of PC or mixed solvent with PC and diethyl cabonate(DEC). Also, even though 1 M-tetraethylamonium perchlorate(TEAPC) of organic electrolyte shows higher specific capacitance, it has longer charge time because of its lower ion mobility.

• Carbon letters
• /
• v.16 no.2
• /
• pp.78-85
• /
• 2015

Activated carbons (ACs) were prepared by activation of coal tar pitch (CTP) in the range of $700^{\circ}C-1000^{\circ}C$ for 1-4 h using potassium hydroxide (KOH) powder as the activation agent. The optimal activation conditions were determined to be a CTP/KOH ratio of 1:4, activation temperature of $900^{\circ}C$, and activation time of 3 h. The obtained ACs showed increased pore size distribution in the range of 1 to 2 nm and the highest specific capacitance of 122 F/g in a two-electrode system with an organic electrolyte, as measured by a charge-discharge method in the voltage range of 0-2.7 V. In order to improve the performance of the electric double-layer capacitor electrode, various mixtures of CTP and petroleum pitch (PP) were activated at the optimal activation conditions previously determined for CTP. Although the specific capacitance of AC electrodes prepared from CTP only and the mixtures of CTP and PP was not significantly different at a current density of 1 A/g, the AC electrodes from CTP and PP mixtures showed outstanding specific capacitance at higher current rates. In particular, CTP-PP61 (6:1 mixture) had the highest specific capacitance of 132 F/g, and the specific capacitance remained above 90% at a high current density of 3 A/g. It was found that the high specific capacitance could be attributed to the increased micro-pore volume of ACs with pore sizes from 1 to 2 nm, and the high power density could be attributed to the increased meso-pore volume.

• Journal of Korean Academic Society of Home Health Care Nursing
• /
• v.7 no.1
• /
• pp.58-72
• /
• 2000

This study was an attempt to encourage the development of a rehabilitation delivery system and programs as a substitute service for hospitalization on the case of car accident patients, such as hospital based home health care nursing services. Various substitute services for hospitalization are required to curtail the length of stay for inpatients who were hospitalized with car accident compensation insurance. It focused on developing an estimation an early discharge day for car accident inpatients based on detailed statements of treatment for 111 inpatients who were hospitalized at the General Hospital in 1997. This study had four specific purposes as follows. First. to find out the utilization of medical services. Second, to estimate the time of early discharge and income increasing effect based on early discharge for those patients. Third, to identify the factors affecting total medical expenditure and the length of stay for those inpatients. Forth, to figure out the need of utilizing home health care nursing service for accident patients. In order to analyze the length of stay and medical expenditure for inpatients who were hospitalized due to car accidents, the authors conducted micro- and macro-analysis of medical and medical expenditure records. Micro-analysis was done by nominal group discussion of 4 expertise with the critical criteria, such as a decrease in the amount of treatment after surgery, treatments, tests, drugs and changes in the test consistency, drug methods, vital signs, start of ROM exercise, doctor's order, patient's outside visiting ability, and stable conditions. In addition to identifying variables affecting medical expenditure, and the length of stay and income effect due to early discharge day, the data was analyzed with a multiple regression analysis and linear regression analysis model by SPSS-PC for windows and Excell program. Results of this study were as follows. First. the mean length of stay was 50.3 days. whereas the mean length of stay due to early discharge was 34.3 days at the hospital. The estimation of time of early discharge depended on the length of stay. The longer the length of stay, the longer the length of time of early discharge : for instance a length of stay under 10 days was estimated as correlating to a mean length of stay of 6.6 days and early discharge of 6.5. The mean length of stay was 217.4 days and the time of early discharge was 110.1 respectively. The mean medical expenditure per day was found to be 169.085 Won and the mean medical expenditure per day showed negative linear trends according to the length of stay at the hospital. The estimation results of the income effect due to being discharged 16 days early was around 2,244,000 won per bed. However. this sum does not represent the real benefits resulting from early discharge, but rather the income increasing amount without considering medical prime cost in the general hospital. Therefore, further analysis is required on the cost containments and benefits as turn over rate per bed as the medical prime costs. The length of stay was most significant and was positive to the total medical expenditure, as expected. Surgery and patient's residential area was also an important variable in explaining medical expenditure. The level of complications was the most significant variable in explaining the length of stay. There was a high level for need a home health care nursing service which further supports early discharge for accident patients. In addition, when the patient was discharged. they needed follow up care for complications suffered during the car accident. $86.8\%$ of discharged patients responded that they needed home health services after early discharge. From these research findings, the following suggestions have been drawn. Strategies on a health care delivery system must be developed in order to focus on the consumer's needs and being planned for 21 century health policy in Korea. Community based intermediate facilities or home health care should be developed for rehabilitation services as a substitute for hospitalization in order to shorten the length of stay would be. A hospital based home health care nursing service. it would be available immediately to utilize by patients who want rehabilitation services as a substitute for hospitalization with the cooperation of car insurance companies.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.94.2-94.2
• /
• 2011

In this work, multi-functional groups, i.e., nitrogen and oxygen, contained microporous carbons (MF-MCs) were prepared by the one step carbonization of the poly(vinylidene chloride-co-acrylonitrile-co-methyl methacryalte) (PVDC-AN-MMA) without activation. The electrochemical performance of MF-MCs was investigated as a function of carbonization temperature. It was found that MF-MCs had a high specific surface area over $800m^2/g$ without additional activation, resulting from the micropore's formation by the release of chlorine groups. In addition, although functional groups decreased, specific surface area was increased with increasing carbonization temperature, leading to the enhanced electrochemical performance. The pore size of the carbon distributed mainly in small micropore of 1.5 to 2 nm, which was idal for aqueous electrolyte. Indeed, the unique microstructure features, i.e. high specific surface area and optimized pore size provided high energy storage capability of MF-MCs. These results indicated that the microporous features of MF-MCs lead to feasible electron transfer during charge/discharge duration and the presence of nitrogen and oxygen groups on the MF-MCs electrode led to a pseudocapacitive reaction.