• 터널과지하공간
• /
• 제5권1호
• /
• pp.1-10
• /
• 1995

The behavior of a jointed rock mass depends mainly on the geometrical and mechanical properties of joints. The failure mode of a rock mass and kinematics of rock blocks are governed by the orientation, spacing, and persistence of joints. The mechanical properties such as dilation angle, shear strength, maximum closure, strength of asperities and friction coeffiient play important roles on the stability and deformation of the rock mass. The normal and shear behaviour of a joint are coupled due to dilation, and the joint deformation depends also on the boundary conditions such as stiffness conditons. In this paper, the joint constitutive law including the dilatant behaviour of a joint is numerically modelled using the edge-to-edge contact logic in distinct element method. Also, presented is the method to quantify the input parameters used in the joint law. The results from uniaxial compression and direct shear tests using the numeical model of the single joint were compared to the analytic results from them. The boundary effect on the behaviour of a joint is verified by comparing the results of direct shear test under constant stress boundary condition with those under constant stiffness boundary condition. The numerical model developed is applied to a complex jointed rock mass to examine its performance and to evaluate the effect of joint dilation on tunnel stability.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권5호
• /
• pp.169-178
• /
• 2008

압축플랜지의 설계는 단순히 종방향 보강재와 횡방향 보강재로 둘러싸인 서브패널(sub-panel)의 극한거동에 대해 적절한 안전율을 도입하여 이루어져 왔다. 그러나, 종방향 보강재의 수와 강성, 횡방향 보강재의 간격, 초기 변형량과 잔류응력의 분포 등 제 영향을 고려해서 압축플랜지 전체의 극한강도를 결정하는 것이 합리적이다. 본 연구에서는 Folded Plate 이론에 근거하여 압축플랜지에 대해 기하강성의 영향, 재료적 비선형성을 고려한 해석 프로그램을 개발하고 이를 바탕으로 국내에서 실제 시공된 강박스거더교의 압축플랜지에 적용하였다.

• 한국지반공학회논문집
• /
• 제21권10호
• /
• pp.123-131
• /
• 2005

본 연구에서는 양압력을 받는 기초구조물의 보강공법으로 앵커를 시공할 경우, 이에 대한 파괴메카니즘 및 안정해석법의 개발에 기초적인 자료를 제공하기 위해 나선형 앵커에 대한 실내인발시험 및 유한요소해석을 수행하였다. 실내인발시험은 강우시 지하수위 상승으로 인해 기초구조물에 양압력이 작용하는 경우를 고려하기 위해 포화사질토 내에서의 하중-변위특성을 분석한 후, 이를 건조시의 경우 등에 대해 유한요소 해석결과와 비교${\cdot}$분석하였으며, 앵커의 극한인발저항력에 미치는 영향인자 및 앵커의 인발에 따른 거동특성 등을 평가하였다. 또한, 군형태 앵커의 설치간격을 변화시켜가면서 하중-인발변위 특성을 비교한 후, 나선형 앵커의 무리효과에 의한 간섭영향 요인을 분석하였다.

• Wind and Structures
• /
• 제8권5호
• /
• pp.325-342
• /
• 2005

This paper deals with the buckling behavior of thin-walled aboveground tanks under wind load. In order to do that, the wind pressures are obtained by means of wind-tunnel experiments, while the structural non linear response is computed by means of a finite element discretization of the tank. Wind-tunnel models were constructed and tested to evaluate group effects in tandem configurations, i.e. one or two tanks shielding an instrumented tank. Pressures on the roof and on the cylindrical part were measured by pressure taps. The geometry of the target tank is similar in relative dimensions to typical tanks found in oil storage facilities, and several group configurations were tested with blocking tanks of different sizes and different separation between the target tank and those blocking it. The experimental results show changes in the pressure distributions around the circumference of the tank for half diameter spacing, with respect to an isolated tank with similar dimensions. Moreover, when the front tank of the tandem array has a height smaller than the target tank, increments in the windward pressures were measured. From the computational analysis, it seems that the additional stiffness provided by the roof prevents reductions in the buckling load for cases even when increments in pressures develop in the top region of the cylinder.

• 대한조선학회논문집
• /
• 제30권2호
• /
• pp.155-160
• /
• 1993

본 논문은 선박 기관실의 특설늑골에 대한 치수결정 방법으로써 하나의 접근방법을 서술하였다. 특설늑골의 치수결정 인자는 실적선의 데이터를 중심으로 조사 연구되었으며, 그 구성인자로는 주로 갑판간 거리, 주기 및 프로펠러 기진 주파수, 만재흘수선, 특설늑골 배치간격, 갑판수 그리고 주기마력 등이다. 이러한 주요인자를 기초로 정하중 및 동하중이 고려된 특설 늑골 치수를 결정할 수 있는 설계식을 유도하였다. 본 논문은 기관실구조의 특설늑골의 치수를 검토할 수 있는 한 방법으로써 설계단계에서 정하중 및 동하중을 고려한 합리적인 설계가 될 수 있을 것으로 판단된다.

• 산업기술연구
• /
• 제20권B호
• /
• pp.87-94
• /
• 2000

A study has been made on the behavior of microscopic fatigue crack growth at the stress level of the fatigue limit with ferrite-martensitic structures. For the above purpose, two types of the microstructures were prepared ; one is the microstructure having the ferrite encapsulating the islands of second phase martensite(FEM), the other is the microstructure with the martensite encapsulating the islands of ferrite(MEF). It has been pointed out that the fatigue limits of these microstructures are related to the critical stress at which the microcrack in the ferrite proceeds to the martensite. The high fatigue limit might be excepted for the MEF microstructure in which the critical crack length would be restricted within the second phase spacing in contrast with the FEM microstruture. However, the fatigue tests shows that no appreciable difference of the fatigue limits among them were recognized. Also, it turned out from the metallographic observations that the micro crack path is very much affected by the microstructures, so that the microcracks grow according to the 3-dimentional situation of its microstructures.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1294-1300
• /
• 2009

Recently, excavations in highly congest urban area have been increased. For the excavations conducted in extremely narrow spaces, we have been developing a novel soil reinforcement system of temporary retaining walls by using deep cement mixing method. The developing method installs largerdiameter ($\Phi$=300~500mm) and shorter reinforcement blocks than previous reinforcement system for mobilizing friction with soils, therefore it has advantages of not only shortening the length of reinforcement system but also reducing the amount of reinforcement. In this study, we performed a numerical analysis of the new reinforcement system by using a commercial finite element program, and evaluated the behavior of the reinforced retaining wall system under various conditions of the length, the diameter, the spacing, and the angle of the reinforcement system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.151-154
• /
• 1998

The layered trivanadate, LiV$_3$O$_{8}$ has been investigated as a cathode material for secondary lithium batteries. Early in its development the preparation method of LiV$_3$O$_{8}$ strongly influenced its electrochemical properties, such as discharge capacity, rate capability and cycling efficiency. In the present experiment, a new synthesis route has been applied to obtain LiV$_3$O$_{8}$ . Instead of the conventional high temperature technique leading to the crystalline form, a solution technique producing the amorphous form has been used. This material, after dehydration, shows an electrochemical performance exeeding that of the crystalline one. The rationale for this behavior mainly lies in microscopic factors, i.e., in the possibility for the unit cell of amorphous LiV$_3$O$_{8}$ to insert up to 9 Li$^{+}$, instead of six for crystalline LiV$_3$O$_{8}$ . The ultrasonically treated products in water were characterized by XRD, TGA, DSC, and SEM. These measurements showed that the ultrasonic treatment process of crystalline LiV$_3$O$_{8}$ causes a decrease in crystallinity and considerable increases in specific surface area and interlayer spacing.g.

• Coupled systems mechanics
• /
• 제3권2호
• /
• pp.147-170
• /
• 2014

In the recent times, dimensions of heavy load carrying vehicle have changed significantly incorporating structural flexibility in vehicle body. The present paper outlines a procedure for the estimation of bridge response statistics considering structural bending modes of the vehicle. Bridge deck roughness has been considered to be non homogeneous random process in space. Influence of pre cambering of bridge surface and settlement of approach slab on the dynamic behavior of the bridge has been studied. A parametric study considering vehicle axle spacing, mass, speed, vehicle flexibility, deck unevenness and eccentricity of vehicle path have been conducted. Dynamic amplification factor (DAF) of the bridge response has been obtained for several of combination of bridge-vehicle parameters. The present study reveals that flexible modes of vehicle can reduce dynamic response of the bridge to the extent of 30-37% of that caused by rigid vehicle model. However, sudden change in the bridge surface profile leads to significant amount of increment in the bridge dynamic response even if flexible bending modes remain active. The eccentricity of vehicle path and flexural/torsional rigidity ratios plays a significant role in dynamic amplification of bridge response.

• Design & Manufacturing
• /
• 제11권3호
• /
• pp.29-34
• /
• 2017

Increased demand for parts with micro-pattern structure made of metals, ceramics, and composites in various fields such as medical ultrasonic sensors, CT collimators, and ultra-small actuator parts. Micro powder injection molding (PIM) is a technology for manufacturing micro size, high volume, complex, precision, net-shape components from either metal or ceramic powder. In the present study, a standard mold with a variable insert core capable of producing various micro patterns was investigated. An injection molding test was performed on a standard mold using a line type micro-pattern core having an aspect ratio of 2, a slenderness ratio of 70, a pattern size of $200{\mu}m$, and a pattern spacing of $150{\mu}m$. During the filling process, the deformation of the mold with large aspect ratio and slenderness ratio was analyzed by the experiment and the numerical simulation according to the position of the gate. We proposed a mold structure that minimizes mold deformation by gate modification and enables uniform pattern filling behavior.