• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.45-56
• /
• 2014

Frozen ground in cold region consists of an upper active layer and lower permafrost which is permanently frozen land. During the summer season, the air temperature is high enough to make the frozen ground melt, which causes the reduction of soil strength and thaw settlement. These phenomena result in structural instability, so it is necessary to apply frozen ground stability techniques. Thermosyphon is a closed natural two-phase convection device to maintain the ground temperature below $0^{\circ}C$ by extracting heat from the ground and discharges it into the atmosphere. Experimental and numerical investigation has been performed to estimate the effect of the refrigerant filling ratio in thermosyphon using R-134a refrigerant and the thermal conductance of the thermosyphon.

• Korean Journal of Materials Research
• /
• v.27 no.6
• /
• pp.331-338
• /
• 2017

This study was carried out to investigate the optimum condition of a friction stir welding process for a joint of AA2219-T87 and AA2195-T8 dissimilar aluminum alloys. These alloys are known to have good cryogenic properties, and as such to be suitable for use in fuel tanks of space vehicles. The welding parameters include the travelling speed, rotation speed and rotation direction of the tool. The experiment was conducted under conditions in which the travelling speed of the tool was 120-300 mm/min and the rotation speed of the tool was 400-800 rpm. To investigate the effect of the rotation direction of the tool, the joining was performed by switching the positions of the two dissimilar alloys. After welding, the microstructure was observed and the micro-hardness were measured; non-destructive evaluation was carried out to perform tensile tests on defect-free specimens. The result was that the microstructure of the weld joint underwent dynamic recrystallization due to sufficient deformation and frictional heat. The travelling speed of the tool had little effect on the properties of the joint, but the properties of the joint varied with the rotation speed of the tool. The conditions for the best joining properties were 600 rpm and 180-240 mm/min when the AA2219-T8 alloy was on the retreating side(RS).

• Nuclear Engineering and Technology
• /
• v.50 no.6
• /
• pp.989-995
• /
• 2018

Argonne National Laboratory of the United States and Kharkov Institute of Physics and Technology (KIPT) of Ukraine have cooperated on the development, design, and construction of a neutron source facility. The facility was constructed at Kharkov, Ukraine, and its commissioning process is underway. The facility will be used for researches, producing medical isotopes, and training young nuclear specialists. The neutron source facility is designed with a provision to include a cryogenically cooled moderator system-a cold neutron source (CNS). This CNS provides low-energy neutrons, which will be used in the scattering experiment and material structures analysis. Cold neutron guides, coated with reflective material for the low-energy neutrons, will be used to transport the cold neutrons to the experimental site. The cold neutron guides would keep the cold neutrons within certain energy and angular space concentrated inside, while most of the gamma rays and high-energy neutrons are not affected by the cold neutron guides. For the KIPT design, the cold neutron guides need to extend several meters outside the main shield of the facility, and curved guides will also be used to remove the gamma and high-energy neutron. The neutron guides should be installed inside a shield structure to ensure an acceptable biological dose in the facility hall. Heavy concrete is the selected shielding material because of its acceptable performance and cost. Shield design analysis was carried out for the CNS guide hall. MCNPX was used as the major computation tool for the design analysis, with neutron and gamma dose calculated separately. Weight windows variance reduction technique was also used in the shield design. The goal of the shield design is to keep the total radiation dose below the $5.0{\mu}Sv/hr$ guideline outside the shield boundary. After a series of iterative MCNPX calculations, the shield configuration and parameters of CNS guide hall were determined and presented in this article.

• Tunnel and Underground Space
• /
• v.26 no.3
• /
• pp.154-165
• /
• 2016

This paper presents experimental results to investigate the affects of acidic solution under loading condition on rock properties. In the experiment, the variations of various rock properties including effective porosity, thermal conductivity, and etc were investigated with different pHs of solution and magnitudes of loading. The results show that the rock property change was increased with low pH under loading. It was predicted that chemical reaction rate would be increased in low pH. Below the crack initiation stress of the rock specimen, the variation of rock property change was reduced with increased loading. It could be explained with the reduced chemical reaction area by the compressional loading if there is no crack generation.

• Journal of Korea Water Resources Association
• /
• v.51 no.10
• /
• pp.853-862
• /
• 2018

An adaptive cut-cell grid based 2D inundation analysis model, K-Flood, is developed in this study. Cut cell grid method divides a grid into a flow area and a non-flow area depending the characteristics of the flows. With adaptive mesh refinement technique cut cell method can represent complex flow area using relatively small number of cells. In recent years, the urban inundation modeling using high resolution and fine quality data is increasing to achieve more accurate flood analysis or flood forecasting. K-Flood has potential to simulate such complex urban inundation using efficient grid generation technique. A finite volume numerical scheme of second order accuracy for space and time was applied. For verification of K-Flood, 1) shockwave reflex simulation by circular cylinder, 2) urban flood experiment simulation, 3) Malpasset dam collapse simulation are performed and the results are compared with observed data and previous simulation results.

• Journal of Korean Society on Water Environment
• /
• v.29 no.6
• /
• pp.746-753
• /
• 2013

The aim of this study was to evaluate artificial fish shelter, which was known to increase prey survival and expand habitat space to improve species diversity and fish communities in a freshwater ecosystem. The experiment was performed at an outdoor test-bed for three months from 2011 by comparing the responses to adjustments in the volume of the artificial patch (juvenile fish shelter, JFS) in the control and experimental groups. Analysis of the environmental conditions over two periods (Period1 ~ 2) showed minor differences in the physichemical characteristics of water quality, phytoplankton, and zooplankton biomass, thus, allowing comparative analysis of feeding ecology. However, high water temperature conditions in Period1 ($25.6{\pm}2.0^{\circ}C$), affected the predation activity of the piscivorous fishes, Coreoperca herzi (C. herzi, size $89{\pm}4mm$). Survival rates of the prey fishes, Rhynchocypris oxycephalus (R. oxycephalus, size $29{\pm}1mm$), improved as the patch volume increased and were higher than those of the control group by 35.9 ~ 46.7%. Analysis showed that JFS reduced the chances of predator-prey encounter, and thereby minimized prey vulnerability.

• Korean Journal of Organic Agriculture
• /
• v.19 no.3
• /
• pp.397-404
• /
• 2011

This experiment was performed to study growth and yield of rice (cv. Dongjinbyeo) and soil properties affected by the application of rice straw, compost, and hairy vetch. An application of rice straw and compost led to the decrease in plant heights and tillers compared with chemical fertilizer whereas hairy vetch application resulted in slight increase. Panicle no per plant was the highest in chemical fertilizer and there was no difference among organic matters. Grain per panicle was no difference among chemical fertilizer, rice straw, and compost whereas was the lowest in hairy vetch application. The 1,000 grain weights did not show any statistic difference and the ripened rate was enhanced in all treatments of organic sources compared with chemical fertilizer. Therefore, an index of rice yield of compost, rice straw, and hairy vetch to chemical fertilizer (100%) was 77, 72, and 103%, respectively. In addition, an application of organic sources led to the increase of soil pore space and this contributed to the improvement of soil physical property.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.16 no.3
• /
• pp.372-377
• /
• 2006

In this paper, we propose sensibility recognition model that recognize user's sensibility using brain waves. Method to acquire quantitative data of brain waves including priority living body data or sensitivity data to recognize user's sensitivity need and pattern recognition techniques to examine closely present user's sensitivity state through next acquired brain waves becomes problem that is important. In this paper, we used pattern recognition techniques to use Multi Layer Perceptron (MLP) that is pattern recognition techniques that recognize user's sensibility state through brain waves. We measures several subject's emotion brain waves in specification space for an experiment of sensibility recognition model's which propose in this paper and we made a emotion DB by the meaning data that made of concentration or stability by the brain waves measured. The model recognizes new user's sensibility by the user's brain waves after study by sensibility recognition model which propose in this paper to emotion DB. Finally, we estimates the performance of sensibility recognition model which used brain waves as that measure the change of recognition rate by the number of subjects and a number of hidden nodes.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.5
• /
• pp.674-682
• /
• 2009

The modular robot is one which was developed to get over limit of the space movement for the mobile robot. The chain type robot in particular is connected by series each other and this form expression method is simple and easy to really make a docking method efficiently. However, the related studies were focused on the movement that used to be combination, and the movement of a cell independent mainly does not consist and have a problem to dock only in a direction, not to be connected with all directions. Therefore, we suggested a modular structure for quick, independent movement to solve such a problem and had own autonomy. In addition, we are intended to get some effectiveness for connection mechanism using one locking motor. In this paper, we dealt with the design for the mechanical and electrical points and docking algorithm including communication method. All of the structure is verified with real action experiment through the shape expressions of various application platform.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.11
• /
• pp.2127-2134
• /
• 2007

The electronic learning helped a learner to overcome the time restriction by providing mobility, instantly and flexibility but the restriction in connection with space on cable computer remained unsolved. Accordingly, the electronic learning has tendency to change into mobile learning environment which allows a learner to overcome time and spatial restriction. However, these mobile devices have a limitation to awareness of learning contents provided over the realtime video movie due to its small display size. Therefore, this paper suggests a technique according to the following priority: for a real time learning image, extract region of study for region of interest, rescale the real time image to its proper size suitable for the display device, and then make it displayed on a wireless PDA. As a result of the experiment, we reduced the calculating time by sampling the field centering on learning contents adaptively and computing the field best suited for device size of the user effectively.