• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.11-14
• /
• 2008

Acoustic design parameters of a half-wave resonator are studied experimentally for acoustic stability in a model acoustic tube. According to standard acoustic-test procedures, acoustic-pressure signals are measured. Quantitative acoustic properties of sound absorption coefficient are evaluated and thereby, the acoustic damping capacity of the resonator is characterized. The diameter and the number of a half-wave resonator and the diameter of the tube are selected as design parameters for optimal tuning of the resonator. Optimum acoustic damping capacity is observed at smaller open area ratio as the resonator diameter increases.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.6
• /
• pp.645-657
• /
• 2015

In this study floor impact noise and structure acceleration response of bare concrete slabs were predicted by using Finite Element Analysis(FEA). Prediction results were compared with experimental results to prove the accuracy of numerical model. Acoustic absorption were addressed by using panel impedance coefficients with frequency characteristics and structural modal damping of numerical model were applied by modal testing results and analysis of prediction and test results. By using frequency response function, the floor acceleration and acoustic pressure responses for various impact sources were calculated at the same time. In the FEA, the natural frequencies and the shapes of vibration and acoustic modes can be estimated through the eigen-value analysis, and it can be visually seen the vibration and sound pressure field and the contribution of major modes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.236-241
• /
• 2007

Recently, in accordance with the cultural progress and the improvement of citizen's consciousness level, it is the real situation that the construction of small-scaled Multi-Purpose Hall where various cultural events could be performed, is on increasing. However, because the most of Multi-Purpose Hall had been designed and built up without any consideration on Acoustic Factor, many problems are on occurring thereat. Because those small-scaled Multi-Purpose Hall have been mostly used with the finishing material which contains a high degree of Acoustic Absorption indiscreetly, both diffusion and reflection of sound are not establishing properly, and since the reverberation of sound is very low, in case of musical performance by musical instrument, its sound hears too arid and stiff, there occurs some acoustic defect such as it becomes difficult for music appreciation with sufficient timbre, so that the capability improvement on the matter is urgently requiring situation. On this viewpoint, this Research has caught the Authenticity of the forecasted value and actually measured value using Acoustic Simulation on the subject of the small-scaled Multi-Purpose Hall, and then intended to propose the optimum acoustic condition on the basis of the Authenticity. As the result, it could be designed a Multi-Purpose Hall equipped with the satisfactory acoustic performance compare with the time before improvement, so that it is considered that such research result could be practically used as the fundamental material when design for other similar small-scaled Multi-Purpose Hall in the future.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.148-152
• /
• 2007

In recent days, on account of the cultural development and the improvement of citizen's consciousness level, it is the real situation that the construction of small-scaled Multi-Purpose Hall where various cultural events could be performed, is on increasing. However, since the most of Multi-Purpose Hall had been designed and built up without any consideration on Acoustic Factor, many problems are on occurring thereat. Since those small-scaled Multi-Purpose Hall have been mostly used with the finishing material which contains a high degree of Acoustic Absorption indiscreetly, both diffusion and reflection of sound are not establishing properly, and because thereverberation of sound is very low, in case of musical performance by musical instrument, its sound hears too arid and stiff, there occurs some acoustic defect such as it becomes difficult for music appreciation with sufficient timbre, so that the capability improvement on the matter is urgently requiring situation. Therefore, this Study has tried to seize the satisfaction level about the small-scaled Multi-Purpose Hall after betterment of the acoustic performance by appraise the acoustic condition of the Hall, using Auralization Technique that can experience Virtual Acoustic Field regarding to the small-scaled Multi-Purpose Hall as its object. It is deemed that such research result could be practically used as the useful material which enables to bring a reduction effect of construction cost as well asenhancement of the acoustic performance through its presupposition?control on the acoustic problem when construction or renovation of other similar small-scaled Multi-Purpose Hall in the future.

• Advances in aircraft and spacecraft science
• /
• v.3 no.3
• /
• pp.351-366
• /
• 2016

Macroperforations improve the sound absorption performance of porous materials in acoustic cavities and in waveguides. In an acoustic cavity, enhanced noise reduction is achieved using porous materials having macroperforations. Double porosity materials are obtained by filling these macroperforations with different poroelastic materials having distinct physical properties. The locations of macroperforations in porous layers can be chosen based on cavity mode shapes. In this paper, the effect of variation of macroporosity and double porosity in porous materials on noise reduction in an acoustic cavity is presented. This analysis is done keeping each perforation size constant. Macroporosity of a porous material is the fraction of area covered by macro holes over the entire porous layer. The number of macroperforations decides macroporosity value. The system under investigation is an acoustic cavity having a layer of poroelastic material rigidly attached on one side and excited by an internal point source. The overall sound pressure level (SPL) inside the cavity coupled with porous layer is calculated using mixed displacement-pressure finite element formulation based on Biot-Allard theory. A 32 node, cubic polynomial brick element is used for discretization of both the cavity and the porous layer. The overall SPL in the cavity lined with porous layer is calculated for various macroporosities ranging from 0.05 to 0.4. The results show that variation in macroporosity of the porous layer affects the overall SPL inside the cavity. This variation in macroporosity is based on the cavity mode shapes. The optimum range of macroporosities in poroelastic layer is determined from this analysis. Next, SPL is calculated considering periodic and nodal line based optimum macroporosity. The corresponding results show that locations of macroperforations based on mode shapes of the acoustic cavity yield better noise reduction compared to those based on nodal lines or periodic macroperforations in poroelastic material layer. Finally, the effectiveness of double porosity materials in terms of overall sound pressure level, compared to equivolume double layer poroelastic materials is investigated; for this the double porosity material is obtained by filling the macroperforations based on mode shapes of the acoustic cavity.

• Korean Journal of Materials Research
• /
• v.4 no.1
• /
• pp.3-8
• /
• 1994

Recently, sound and mechanical vibration are becoming important problems in our life. In the present study, the measurement of vibration absorption characteristics of barium titanate ceramics and the investigation of its relationship to microstructures were carried out. The barium titanate ceramics is expected to be better vibration absorption material owing to its chemical and physical stability than other conventional vibration absorbers like glasswool board. Barium titanate ceramics were prepared by sintering fiberous $BaTiO_{3}$ crystallites in order to enhance the vibration absorption characteristics. The fiberous $BaTiO_{3}$ ceramics were prepared through the ionic exchange after the preparation of fiberous $K_2Ti_4O_9$ with 0.2$\mu\textrm{m}$, 1.2$\mu\textrm{m}$, 2.0$\mu\textrm{m}$, diameter length by KDC method. The fiberous crystallites were oriented in a plane perpendicular to the press direction and sintered. The investigation of the grain diameters of the sintered ceramics, equivalent factor, electromechanical coupling factor($k_1$), and the generated voltage(V) shows that the grain's diameter decreases with the increase of the diameter of the used fiberous crystallites. The vibration absorption increases the crystallites' diameter. That means that the vibration absorption increases with the internal friction of grain boundary. Which was identified by the investigation of the equivallent circuit.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.802-806
• /
• 2004

For the protection of the local air quality and the global atmosphere, the emissions of trace species including nitric oxides (NO and NO$_2$) from gas turbines are regulated by local governments and by the International Civil Aviation Organization. In-situ measurements of such species are needed not only for the development of advanced low-emission combustion concepts but also for providing emissions data required for the sound assessment of the effects of the emissions on environment. We have been developing a laser absorption system that has a capability of simultaneous determination of NO and NO$_2$concentrations in the exhaust jets from aero gas turbines. A diode laser operating near 1.8 micrometer is used for the detection of NO while a separated visible tunable diode laser operating near 676 nanometers is used for NO$_2$. The sensitivities at elevated temperature conditions were determined for simulated gas mixtures heated up to 500K in a heated cell of a straight 0.5 m optical path. Sensitivity limits estimated as were 30 ppmv-m and 3.7 ppmv-m for NO and NO$_2$, respectively, at a typical exhaust gas temperature of 800K. Experiments using the simulated exhaust flows have proven that $CO_2$ and $H_2O$ vapor - both major combustion products - do not show any interference in the NO or NO$_2$ measurements. The measurement system has been applied to the NO/NO$_2$ measurements in NO and NO$_2$ doped real combustion gas jets issuing from a rectangular nozzle having 0.4 m optical path. The lower detection limits of the system were considerably decreased by using a multipass optical cell. A pair of off-axis parabola mirrors successfully suppressed the beam steering in the combustion gas jets by centralizing the fluctuating beam in sensor area of the detectors.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.8
• /
• pp.787-794
• /
• 2010

Recently, with sudden increase of supplying rate of cars and quantity of goods transported, traffic noisy becomes one of important factors obstruct environment of exhibition and view facilities have purpose in calmness and unsatisfaction about this is high now. Therefore, in case of exhibition and view facilities, it has to be grasped that satisfaction degree about the noisy in and out of the exhibition room by performing effect valuation on traffic noisy from design step. However the level of internal noise cannot be measured at the design phrase of the structure due to the noise of traffic. Up until now a walls transmission loss, based on the law of mass, is predicted using this method. However measuring the internal sound level after actual construction reveals that there is a large difference from measurements made at the design stage, and it is very difficult to find a solution after the opening of the structure. From research looking from this perspective the internal sound level was predicted- calculating the internal sound absorption ability, using acoustic simulation and loss prevention of an insulated wall- based on data collected to evaluate the internal sound of an exhibition room at a Folk Museum adjacent to a freeway. The results of this research are considered to provide important data for the prediction of internal sound level at the time of construction of exhibition facilities similar to this.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.8
• /
• pp.802-808
• /
• 2009

In this paper, the experimental study on the identification of noise sources and noise transmission paths was carried out for the cabin noise control of construction equipment. In order to investigate noise and vibration characteristics of cabin structure, sound absorption, transmission, and radiation tests were performed using cabin assembly models. The noise/vibration source levels were obtained from the real cabins of wheel loader and excavator. Using transfer functions of cabins and real cabins' source data, cabin noise was decomposed into airborne and structureborne noise transmissions. Finally noise sources and major transmission paths were successfully identified for wheel loader and excavator's cabins.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.141-142
• /
• 2015

This literature study is focused on the improvement of lightweight concrete in perspective of foaming agent. Lightweight concrete is the cured concrete as putting required amount of foaming agent to slurry which is a mixture of a certain amount of cement, sand, and water. It has lower density than general concrete, because foaming agent disintegrates numerous bubbles evenly and independently. Thus, it is capable of lightening the weight and great for sound absorption and insulation, In foreign countries, studies for structural lightweight concrete mainly of tunnel grouting and weight lightening of heavy structures are going along actively. Domestically, exterior panel and ALC blocks are alternatively used for flooring. Therefore, this research consider improvement of lightweight concrete in perspective of foaming agent with foundation study.