• Textile Coloration and Finishing
• /
• v.15 no.6
• /
• pp.55-62
• /
• 2003

Wool fabrics were dyed with the aqueous solution of C. I. Red Acid 114 mixed with methanol dissolving three kinds of barely water soluble ketones, acetophenone, 2-pentanone, and 3-pentanone. The steric hinderance and the orientation of the bigger hydrophobic part of the solvated dye molecules to the fiber slowed down the dying rate, however, loosening the wool molecule, say a little swelling, disaggeregating the dye molecules, and attaining the higher dye concentration on the fiber surface by the added solvents increased the amount of dye on the fabric. The higher concentration or/and the higher dyeing temperature helped loosen fiber molecules and made it easier for the solvated dye molecules to penetrate into the inside of the fiber. Acetophenone, the most influential solvent used, showed that the ability to loosen fiber molecules was the most important of all the three positive solvent actions mentioned above. The considered mechanism provided before reflected the fact that the dye uptake on the fabric dyed with the solvents included, except for 0.034M and 0.051M of acetophenone, was even lower than that without any solvents at $50^\circ{C}$, but all the solvents added to the dye bath increased the dye uptake on the fiber at $70^\circ{C}$.

• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.82-90
• /
• 1992

To optimize the foam dyeing procedures for polyester and polyester/nylon blended non-woven fabrics, the effects of organic solvents and surfactants were investigated by measuring the foam heights and surface tensions of the foam dyeing solution. The results of the experiments can be summarized as follows: 1) Organic solvents and surfactants (sodium lauryl sulphate: SLS) solution lower the surface tension (ST) of the water, but ST lowering rate of SLS solution is greater than that of solvents. For a 0.25% SLS solution, the minimum surface tension was 30.3 dyne/cm, which is nearly the same value for organic solvents. 2) For 0.25% SLS solutions, additional adding of a 4.0% organic solvent makes the foam height (FH) be its maximum. 3) At 0.6 g/ι dye concentration, incorporation of 0.4% SLS makes the surface tension of the foam solution be its minimum. The foam height did not show any trend due to the dye type. 4) The effect of foam stabilizers (sodium alginate (Alg-Na) and hydroxy ethyl cellulose (HEC)) were also investigated. The foam height of the foaming solution with HEC was greater than that with Alg-Na. The foam stability of the foaming solution with Alg-Na was better than that with HEC.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.3
• /
• pp.406-412
• /
• 1998

Such extraction conditions as the kinds of solvent, extracting temperature, extracting time, ratio of material to solvent and particle size of material, were studied to maximize the extraction of oleoresin from chipi. Larger amount of soluble solids were extracted from seeds with nonpolar solvents (hexane, pentane, ether) for extraction, because the seeds contained large amount of crude fats and monoterpene(limonene) volatile compounds. Larger amount of soluble solids were extracted from peel with polar solvents(methanol, ethanol) of extraction because of large amount of water soluble colors, sugars and oxygenated terpene bolatile compounds in the peel. The application of the solvents in intermediate polarity (dichloromethane, acetone) resulted in more effective extraction of soluble solid and volatile compounds. Expecially, dichloromethane was an excellent solvent in extraction of volatile compounds. In the concern of volatile compound recovery yield, the optimum extraction conditions, such as temperature, time, mixing ratio of material to dichloromethane and mean particle size, were $25^{\circ}C$, 10min, 1:10(w/v), 355~250${\mu}{\textrm}{m}$ for chopi peels and 3$0^{\circ}C$, 10min, 1:8(w/v), 355~250${\mu}{\textrm}{m}$ for chopi seeds, respectively.

• Journal of the Korean Chemical Society
• /
• v.17 no.3
• /
• pp.207-212
• /
• 1973

The mechanical degradation of poly (-vinylacetate) in several mixed solvents (dioxane-n-butanol, dioxane-sec-butanol, dioxane-ethyleneglycol, dioxane-kerosene.) was studied using the capillary flow method. The velocity constant of scission reaction (k) and the limited degree of polymerization (g) were compared at the same value of [${\eta}$], which is considered as the parameter of molecular dimension of polymers in solution. As result, (k) did not change much, even if the species and the volume fraction of poor (non-) solvents changed, while the value of (g) changed according to the species of poor solvents and the value of [${\eta}$]. From the facts described above, It follows that the limited degree of polymerization (g) were affected by the composition and distribution of mixed solvent molecules around the polymer chain, and the value of $\alpha$ (at [${\eta}$] = $KM^a$) in the polymer solution.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.8 no.1
• /
• pp.88-94
• /
• 1998

Korea has been rapidly industrialized during the past 35 years. During this period, Korea has emphasized only production and workers health has been ignored. Workers are most frequently exposed to organic vapors, such as thinners. This study was performed to evaluate worker exposures to organic solvents by size and type of industry. Results are summarized below. Workers were exposed to mixtures of toluene, xylenes, trichloroethylene, n-hexane, acetone, methanol, n-butanol, n-butyl acetate, and MIBK. Considering additive effects of the compounds, exposure indices (EIs) were calculated. It was found that worker exposures to organic solvents were highest in small industries and lowest in large industries. During a day shift, the highest exposure was indicated 3 - 5 p.m. in the afternoon. Workers in small industries had potential exposures exceeding permissible exposure limits for organic solvents. Local exhuast systems were inappropriate and respiratory protective devices were not supplied to the workers in small industries. Neither program for safe use and storage of toxic materials nor program for respirators was found in any of the plants investigated. Based on the results of the study, workers of small scale industries should be considered first in industrial health.

• Journal of Environmental Health Sciences
• /
• v.24 no.2
• /
• pp.80-87
• /
• 1998

To evaluate the effects on health by exposure to low dose organic solvents, the author analyzed the air concentration of mixed organic solvents (toluene, xylene, butylacetate) at worker's breathing zone during painting, some laboratory findings of blood (WBC, RBC, Hb, Hct, SGOT, SGPT, TC, TG, HDL-C, LDL-C, IgG, IgM, IgA and IgE) and urine (hippuric acid, urinary protein, urobilinogen), surveyed the subjective symptoms those were obtained from 35 male workers exposed to mixed organic solvents, and 25 male workers not exposed to organic solvents who worked in car repair workshops in Taejon area from December 1, 1995, to February 29, 1996. The results were as follows: 1. The mean concentration of urinary hippuric acid of car painting worker group (organic solvent exposure group) was 0.76$\pm$ 0.21 g/l, which is significantly higher than that of non-exposed group. 2. In hematologic findings, the values of RBC, TC, LDL-C, IgG and IgE in the exposure group were significantly lower than those of the nonexposed group, but SGOT and SGPT in the exposure group were significantly higher than those of the non-exposed group. 3. Urinary hippuric acid levels showed positively correlated with toluene, urobilinogen and HDL-C levels, but those were negatively correlated with RBC, LDL-C, IgM levels. 4. Rates of the subjective symptoms such as "dizziness", "appetite loss", "weight loss", "palpitation", "chest tightness", "sore throat and eye discomfort", "tingling sense and acrodynia", "illusion or hallucination" and "decreaased motor power" were significantly higher in the exposure group than those of the non-exposed group.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.3
• /
• pp.11-14
• /
• 2018

$MgB_2$ superconducting properties have been investigated with the surface-treated boron powders using the chemical solvents. Various solvents were used such as acetone, ethanol, methanol, and water to possibly modify the surface condition of raw boron powders as received. This treatment was done at an argon gas environment inside the glove box to reduce the further contamination during and after chemical treatments. It was found that $T_c$ values were increased to 37.58-37.73 K from the pure sample of 37.50 K when they were treated in inert environment. High- fields $J_c$ at both 5 & 20 K was all increased regardless of any kinds of chemical treatments mentioned above. It is also noted that the $J_c$ at low-fields were increased in the order of solvents: ethanol > acetone > pure $MgB_2$ = methanol > water.

• BMB Reports
• /
• v.36 no.4
• /
• pp.367-372
• /
• 2003

The stability of four hemoglobins (Hb) in dimer forms (low concentration) were investigated by the kinetics of denaturation. The rate constants of denaturation were obtained by variation of 280 nm absorption versus time in 10 mM Tris-HCl, 10 mM EDTA, pH 8.0 at $45^{\circ}C$ in the absence and presence of 0.5 M ethanol, dimethyl sulfoxide (DMSO), formamide, and glycerol. The results show the trend of rate constants in different co-solvents in the following order: chicken hemolysate < human hemolysate and chicken Hb D < chicken Hb A. The buried surface area was calculated for Hb samples in the absence of cosolvents. Accordingly, the trend points out that: chicken Hb D > chicken Hb A > human Hb A. These results suggest that both chicken hemolysate and chicken Hb D are relatively more stable than human and chicken Hb A, respectively. However, the denaturation rate constants of Hb in different co-solvents have designated the following order: ethanol > DMSO > formamide > glycerol. As a matter of fact, this phenomenon is an indication of an increase in the denaturation capacity (DC) and hydrophobicity, and a decrease in the surface tension of the solution in the preceding co-solvents.

• Korean Journal of Food Science and Technology
• /
• v.17 no.6
• /
• pp.490-494
• /
• 1985

The effect of organic solvents on the stability and catalytic activity of the microbial lipase from Rhizopus arrhizus for interesterification of fats and oils has been examined. The reaction system used was nonaqueous solvent system (two phase system). The solvents examined were 5 hydrocarbons (n-hexane, n-heptane, n-octane, isooctane, and cyclohexane) and 3 ethers (diethylether, diisopropylether, di-n-butylether). The results revealed that diisopropylether and isooctane are superior to the other solvents examined for interesterification of fats and oils in two phase systems.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.2
• /
• pp.615-621
• /
• 2013

Solvolyses of isobutyl chloroformate (4) in 43 binary solvent mixtures including highly aqueous media, water, $D_2O$, $CH_3OD$, 2,2,2-trifluoroethanol (TFE) as well as aqueous 1,1,1,3,3,3-hexafluoro-isopropanol (HFIP) solvents were performed at $45^{\circ}C$, in order to further investigate the recent results of D'Souza, M. $J^1$. et al.; solvolyses of 4 are found to be consistent with the proposed mechanism ($Ad_E$). The variety of solvent systems was extended to comprise highly ionizing power solvent media ($Y_{Cl}$ > 2.7 excepted for aqueous fluorinated solvents and pure TFE solvent) to investigate whether a mechanistic change occurs as solvent compositions are varied. However, in case of 18-solvent ranges having aqueous fluorinated solvent systems (TFE-$H_2O$ and HFIP-$H_2O$) and/or having $Y_{Cl}$ > 2.7 solvent systems, the solvent effect on reactivity for those of 4 are evaluated by the multiple regression analysis as competition with $S_N2$ - type mechanism. And in pure TFE and 97 w/w % HFIP solvents with high $Y_{Cl}$ and weak $N_T$, these solvolyses are understood as reactions which proceed through an ionization ($S_N1$) pathway.