• Journal of the Korean Applied Science and Technology
• /
• v.30 no.2
• /
• pp.290-296
• /
• 2013

We analysed interfacial traps in organic thin-film transistors (TFTs) in which pentacene and 6,13-bis(triisopropylsilylethynyl)-pentacene (TIPS-pentacene) organic semiconductors were deposited by means of vacuum-thermal evaporation and drop-coating methods, respectively. The thermally-deposited pentacene film consists of dentritic grains with the average grain size of around 1 m, while plate-like crystals over a few hundred microns are observed in the solution-processed TIPS-pentacene film. From the transfer characteristics of both TFTs, lower subthreshold slope of 1.02 V/decade was obtained in the TIPS-pentacene TFT, compared to that (2.63 V/decade) of the pentacene transistor. The interfacial trap density values calculated from the subthreshold slope are about $3.4{\times}10^{12}/cm^2$ and $9.4{\times}10^{12}/cm^2$ for the TIPS-pentacene and pentacene TFTs, respectively. Herein, lower subthreshold slope and less interfacial traps in TIPS-pentacene TFTs are attributed to less domain boundaries in the solution-processed TIPS-pentacene film.

• Korean Journal of Materials Research
• /
• v.30 no.3
• /
• pp.131-135
• /
• 2020

Silver nanowire (AgNW) networks have been adopted as a front electrode in Cu(In,Ga)Se2 (CIGS) thin film solar cells due to their low cost and compatibility with the solution process. When an AgNW network is applied to a CIGS thin film solar cell, reflection loss can increase because the CdS layer, with a relatively high refractive index (n ~ 2.5 at 550 nm), is exposed to air. To resolve the issue, we apply solution-processed ZnO nanorods to the AgNW network as an anti-reflective coating. To obtain high performance of the optical and electrical properties of the ZnO nanorod and AgNW network composite, we optimize the process parameters - the spin coating of AgNWs and the concentration of zinc nitrate and hexamethylene tetramine (HMT - to fabricate ZnO nanorods. We verify that 10 mM of zinc nitrate and HMT show the lowest reflectance and 10% cell efficiency increase when applied to CIGS thin film solar cells.

• Journal of Microbiology and Biotechnology
• /
• v.33 no.9
• /
• pp.1170-1178
• /
• 2023

Food allergy represents a severe problem for many societies, including sensitive populations, academies, health authorities, and the food industry. Peanut allergy occupies a special place in the food allergy spectrum. To prevent consumption by consumers suffering from a peanut allergy, a rapid and sensitive detection method is essential to identify unintended peanut adulteration in processed foods. In this study, we produced four monoclonal antibodies (MAbs; RO 3A1-12, PB 4C12-10, PB 5F9-23, and PB 6G4-30) specific to thermo-stable and soluble proteins (TSSPs) of peanut and developed an enzyme-linked immunosorbent assay (ELISA) based on the MAbs. Among them, PB 5F9-23 MAb was firmly bound to Ara h 1, and other MAbs strongly reacted to Ara h 3 in the Western blot analysis. An antibody cocktail solution of the MAbs was used to enhance the sensitivity of an indirect ELISA, and the limit of detection of the indirect ELISA based on the antibody cocktail solution was 1 ng/ml and improved compared to the indirect ELISA based on the single MAb (11 ng/ml). The cross-reaction analysis revealed the high specificity of developed MAbs to peanut TSSPs without cross-reaction to other food allergens, including nuts. Subsequently, analyzing processed foods by indirect ELISA, all foods labeled as containing peanuts in the product description were confirmed to be positive. The results indicate that the developed antibodies exhibit high specificity and sensitivity to peanuts and can be used as bio-receptors in immunoassays or biosensors to detect intentional or unintentional adulteration of peanuts in processed foods, particularly heat-processed foods.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.256-256
• /
• 2016

기존의 디스플레이 기슬은 마스크를 통해 특정 부분에만 유기재료를 증착시키는 방법을 사용하였으나, 기판의 크기가 커짐에 따라 공정조건에 제약이 발생하였다. 이를 해결하기 위해 최근 용액 공정에 대한 연구가 활발히 진행되고 있다. 용액 공정은 기존 진공 증착 방식과 비교하였을 때 상온, 대기압에서 증착이 가능하며 경제적이고, 대면적 균일 증착에 유리하다는 장점이 있다. 반면, 용액 공정으로 제작한 소자는 시간이 지남에 따라 점차 전기적 특성이 변하는 aging effect를 보인다. Aging effect는 용액에 포함된 C기와 OH기 기반의 불순물의 영향으로 시간의 경과에 따라서 문턱전압, subthreshold swing 및 mobility 등의 전기적 특성이 변하는 현상으로 고품질의 박막을 형성하기 위해서는 고온의 열처리가 필요하다. 지금까지 고품질 박막 형성을 위한 열처리는 퍼니스 (furnace) 장비에서 주로 이루어졌는데, 시간이 오래 걸리고, 상대적으로 고온 공정이기 때문에 유리, 종이, 플라스틱과 같은 다양한 기판에 적용하기 어렵다는 단점이 있다. 따라서, 본 연구에서는 $100^{\circ}C$ 이하의 저온에서도 열처리가 가능한 microwave irradiation (MWI) 방법을 이용하여 solution-processed InGaZnO TFT를 제작하였고, 기존의 열처리 방식인 furnace로 열처리한 TFT 소자와 aging effect를 비교하였다. 먼저, solution-processed IGZO TFT를 제작하기 위해 p type Si 기판을 열산화시켜서 100 nm의 SiO2 게이트 산화막을 성장시켰고, 스핀코팅 방법으로 a-IGZO 채널층을 형성하였다. 증착후 열처리를 위하여 1000 W의 마이크로웨이브 출력으로 15분간 MWI를 실시하여 a-IGZO TFT를 제작하였고, 비교를 위하여 furnace N2 gas 분위기에서 $600^{\circ}C$로 30분간 열처리한 TFT를 준비하였다. 제작된 직후의 TFT 특성을 평가한 결과, MWI 열처리한 소자가 퍼니스 열처리한 소자보다 높은 이동도, 낮은 subthreshold swing (SS)과 히스테리시스 전압을 가지는 것을 확인하였다. 한편, aging effect를 평가하기 위하여 제작 후에 30일 동안의 특성변화를 측정한 결과, MWI 열처리 소자는 30일 동안 문턱치 전압(VTH)의 변화량 ${\Delta}VTH=3.18[V]$ 변화되었지만, furnace 열처리 소자는 ${\Delta}VTH=8.56[V]$로 큰 변화가 있었다. 다음으로 SS의 변화량은 MWI 열처리 소자가 ${\Delta}SS=106.85[mV/dec]$인 반면에 퍼니스 열처리 소자는 ${\Delta}SS=299.2[mV/dec]$이었다. 그리고 전하 트래핑에 의해서 발생하는 게이트 히스테리시스 전압의 변화량은 MWI 열처리 소자에서 ${\Delta}V=0.5[V]$이었지만, 퍼니스 열처리 소자에서 ${\Delta}V=5.8[V]$의 큰 수치를 보였다. 결과적으로 MWI 열처리 방식이 퍼니스 열처리 방식보다 소자의 성능이 우수할 뿐만 아니라 aging effect가 개선된 것을 확인할 수 있었고 차세대 디스플레이 공정에 있어서 전기적, 화학적 특성을 개선하는데 기여할 것으로 기대된다.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.21 no.46
• /
• pp.19-32
• /
• 1998

This paper addresses the processing route of parts and economic design in flexible manufacturing systems (FMSs) employing AGVs for Transport. Parts are processed through several workstations according to operation sequences. The machine of each workstation can do multiple operation functions. The operation stage of a part can be processed in several workstations, which are non-identical in functional performance. The objective of this paper is to determine the processing route of parts, number of machines at each workstation, number of vehicles. The model is assumed that the operation stage of parts can be processed at the only one among several available workstations. Parts are transported by automated guided vehicle system(AGVS). The decision criteria is to minimize the sum of processing cost, travel cost, operating cost. A model formulation is represented. A solution algorithm is suggested by using mathematical programming and simulation technique, and a numerical example is shown.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.6
• /
• pp.271-274
• /
• 2011

Screen-printed source and drain electrodes were used for a spin-coated and inkjet-processed zinc-tin oxide (ZTO) TFTs for the first time. Source and drain were silver nanoparticles. Channel length was patterned using screen printing technology. Different silver nanoinks and process parameters were tested to find optimal source and drain contacts Relatively good electrical properties of a screen-printed inkjet-processed oxide TFT were obtained as follows; a mobility of 1.20 $cm^2$/Vs, an on-off current ratio of $10^6$, a Vth of 5.4 V and a subthreshold swing of 1.5 V/dec.

• The Journal of Fisheries Business Administration
• /
• v.21 no.2
• /
• pp.55-84
• /
• 1990

The objective of this study is to develop an inventory model for the inventory management of a stocking point which sells processed fisheries products. The study, first of all, sets up fisheries processing companies, food companies, apparel companies, pharmaceutical companies and electronic and electrical companies as a population. Then, a comparative study is empirically applied to obtain the inventory characteristics of final products by industry through a survey of a sample selected by a random sampling procedure. The major inventory characteristics of processed fisheries products obtained from the above analysis can be summarized as follows : 1) The major demand characteristics of processed fisheries products is to have wide seasonal fluctuations because the supply of raw materials (i.e., fisheries products) heavily depends on the productive capacity of nature. 2) It has found that fisheries processing companies are the worst in inventory management among the various industries selected in the sample. However, the self-rating of inventory management system by inventory managers of companies shows that the fisheries processing companies are relatively higher than the other companies. 3) The portion of inventory holding cost out of inventory relevant cost is very high for processed fisheries products compared with final products of the other industries. 4) Processed fisheries products are distributed to final consumers through roughly two distribution echelons and take a parallel type inventory system for their distribution structure. In order to develop an inventory model which reflects the inventory characteristics of processed fisheries products mentioned in the above, an inventory model with partial backorders is developed under the situation of stochastic lead time under the consideration of the inventory characteristics of processed fisheries products and then an iterative solution method is provided for the model. Then this study analyzes sensitivity for the standard deviation of lead time in the model by numerical examples.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.27-29
• /
• 2003

Solution-based MOD-TFA deposition technology of YBCO layers offers a route to low-cost YBCO coated conductors. Since the structures and properties of grown thin film by MOD process are strongly influenced by chemistry of precursor solution, the chemical modification of precursor solution for MOD process are important for improvement of the electrical properties of YBCO films. In this study, the precursor solution for MOD process are modified by chemical additives and solvents. The microstructure and texture of YBCO films grown by chemically modified precursor solution were characterized with SEM/EDS, XRD.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.600-604
• /
• 2011

Solution processed IGO thin films were prepared using a general chemical solution route by spin coating. The effect of the annealing temperature of IGO thin films based on the ratio of 2:1 of indium to gallium on crystallization was investigated with varying annealing temperature from $300^{\circ}C$ to $600^{\circ}C$. The electronic device characteristic of IGO thin film was investigated. The solution-processed IGO TFTs annealed at 300 and $600^{\circ}C$ in air for 1 h exhibited good electronic performances with field effect mobilities as high as 0.34 and 3.83 $cm^2/V{\cdot}s$, respectively. The on/off ratio of the IGO TFT in this work was $10^5$ with 98% transmittance.

• Journal of Adhesion and Interface
• /
• v.24 no.3
• /
• pp.86-94
• /
• 2023

To fabricate all-solution-processed flexible Organic Light-Emitting Diodes (OLEDs), we demonstrated a bonding technology using a polyethyleneimine (PEI) as an adhesion layer between the two substrates. As the adhesion layer requires not only a high adhesion strength, but also a high current density, we have tried to find out the optimum condition which meets the two requirements at the same time by changing experimental factors such as PEI concentration, thickness of the layer and by mixing some additives into the PEI. The adhesion strength and the electrical current density were investigated by tensile tests and electron only device (EOD) experiments, respectively. The results showed that at higher PEI concentration the adhesion strength showed higher value, but the electrical current through the PEI layer decreased rapidly due to the increased PEI layer thickness. We added Sorbitol and PolyEthyleneGlycohol (PEG) into the 0.1 wt% PEI solution to enhance the adhesion and electrical properties. With the addition of the 0.5 wt% PEG into the 0.1 wt% PEI solution, the device showed an electrical current density of 900 mA/cm² and a good adhesion characteristic also. These data demonstrated the possibility of fabricating all-solution-processed OLEDs using two-substrate bonding technology with the PEI layer as an adhesion layer.