• 청정기술
• /
• 제7권1호
• /
• pp.65-74
• /
• 2001

본 연구는 디젤엔진에서 배출되는 NOx환원용 촉매로서 산화반응에서 우수한 활성을 나타내고 있는 페롭스카이트상의 $LaCoO_3$을 sol-gel 공정을 이용하여 촉매코팅용액을 제조한 후, 이를 기존의 dip-coating방법보다 코팅시간, 코팅량, NO-CO 산화 환원 반응에 있어서 경제적이고 효율적인 modified dip-coating방법을 이용하여 촉매코팅필터를 제조하고 이를 후처리장치에 부착함으로써 디젤엔진에서 배출되는 배가스를 효과적으로 제거시키고자 한다. 실험결과, modified dip-coating방법이 기존의 dip-coating방법에 비해서 코팅에 소요되는 용액량이 8.3배 코팅시간 83.3배 단축되었으며, 코팅량은 2~3배정도 커지고, NO-CO 산화 환원 반응성도 1.1~1.8배 가량 증가하였다. 그리고 코팅점도는 $0.006202kg{\cdot}m/sec$을 이용하여 코팅횟수 2회, 코팅량은 88.56mg/g에서 우수한 반응을 보였다. 또한 세라믹 필터의 셀수에 있어서는 200 CPSI가 적절함을 확인할 수 있다.

• 한국산학기술학회논문지
• /
• 제10권9호
• /
• pp.2396-2401
• /
• 2009

본 연구는 건축자재로 널리 사용되는 PVC 바닥상재의 표면을 스크래치로부터 보호하기 위하여 기존에 사용하는 광경화형 우레탄-아크릴 수지에 내마모성을 향상시킨 광경화형 하드 코팅액 개발에 관한 것이다. PVC 바닥상재용으로 사용되는 내마모성이 없는 우레탄-아크릴 수지에 $Al_2O_3$(Al-160SG-3), $Al(OH)_3$(SH-8W) 및 $SiO_2$(KS-5000) 등 서로 다른 내마모성을 지닌 물질을 분말 형태로 수지의 양 대비 함량(wt%)을 $10{\sim}30%$로 변화하여 첨가한 후 링밀(Ring Mill)을 사용, 배합하여 수지의 내마모성을 향상시킨 하드 코팅액을 제조하였다. 제조한 하드 코팅액은 코팅층의 두께조절이 가능한 코팅(Bar-coating)을 사용하여 PVC 바닥상재에 코팅 한 후 내마모성, 연필경도, 부착력, 코팅두께 등의 코팅층 표면물성을 평가하였다. 연구결과, 수지에 $Al_2O_3$ 분말 30%를 혼합하여 제조한 하드 코팅액이 내마모성 1등급, 연필경도 H, 부착력 100%로 가장 좋은 물성을 보였으며, 전반적으로 입자크기가 작고, 분말 함량이 많을수록 또한 코팅두께가 두꺼워 질수록 경도 및 내마모성이 우수한 것으로 나타났다.

• 한국표면공학회지
• /
• 제54권6호
• /
• pp.315-323
• /
• 2021

In general, surface treatments of electroless Ni-P coating are extensively applied in the industry due to their excellent properties for considerable wear resistance, hardness, corrosion resistance. This study aims to determine the effect of ultrasonic conditions on the morphology, alumina content, roughness, hardness, and corrosion resistance of electroless Ni-P-Al₂O₃ composite coatings. The characteristics were analyzed by Energy-dispersive X-ray spectroscopy (EDX), x-ray diffractions (XRD), and atomic force microscopy (AFM), etc. In this study, the effect of ultrasonic condition uniformly distributed alumina within Ni-P solution resulting in a smoother surface, lower surface roughness. Furthermore, the corrosion resistance behavior of the coating was analyzed using tafel polarization curves in a 3.5 wt.% NaCl solution at 25 ℃. Under ultrasonic, Al₂O₃ content in Ni-P composite solution increased from 0.5 to 5.0 g/L, Al₂O₃ content at 3.0 g/L was showed a significantly enhanced corrosion resistance. These results suggested that ultrasonic condition was an effective method to improve the properties of the composite coating.

• 한국표면공학회지
• /
• 제40권2호
• /
• pp.70-76
• /
• 2007

Ni-P-SiC composite coating layers were prepared by electroless plating method and their deposition rate, codeposition of SiC, morphology, surface roughness, hardness, wear and friction properties were investigated. The deposition rate was kept almost constant independent of the concentration of SiC in the plating solution and the codeposition of SiC in the composite coating layer increased with increased concentration of SiC in the plating solution except the early stage. Vickers microhardness increased with respect to the increased codeposition of SiC and the heat treatment at $300^{\circ}C$ in air for 1 hour. It was found that the wear volume decreased with increased up to 50 wt.% of SiC codeposition, and that friction coefficient increased gradually with increased codeposition of SiC. Considering the wear and the friction behaviors, the composite coating layer obtained by using 50 wt.% of SiC codeposition is desirable for the practical application for anti-wear and anti-friction coatings.

• 한국표면공학회지
• /
• 제51권4호
• /
• pp.224-230
• /
• 2018

In this study, Mg films were prepared on hot dip aluminized steel (HDA) by using a sputtering method as a high corrosion resistance coating. The corrosion resistance of the Mg films was improved by controlling the morphology and the crystal structure of films by adjusting the Ar gas pressure during the coating process. Anodic polarization measurement results confirm that the corrosion resistance of the Mg films was affected by surface morphology and crystal structure. The corrosion resistance of the Mg coated HDA specimen increased with decreasing crystal size of the Mg coating and it was also improved by forming a film with denser morphology. The crystal structure oriented at Mg(101) plane showed the best corrosion resistance among crystal planes of the Mg metals, which is attributed to its relatively low surface energy. Neutral salt spray test confirmed that corrosion resistance of HDA can be greatly improved by Mg coating, which is superior to that of HDG (hot dip galvanized steel). The reason for the improvement of the corrosion resistance of Mg films on hot dip aluminized steel was due to the barrier effect by the Mg corrosion products formed by the corrosion of the Mg coating layer.

• 한국표면공학회지
• /
• 제53권4호
• /
• pp.182-189
• /
• 2020

Indium tin oxide (ITO) used a transparent electrode of a photoelectric device has a low sheet resistance and a high transmittance. However, ITO is disadvantageous in that the process cost is expensive, and the process time is long. Silver nanowires (AgNWs) transparent electrodes are based on a low cost solution process. In addition, it has attracted attention as a next-generation transparent electrode material that replaces ITO because it has similar electrical and optical characteristic to ITO, it is noted as a. AgNW thin films are mainly produced by spin-coating. However, the spin-coating process has a disadvantage of high material loss. In this study, the material loss was reduced by using about 2~10 ㎕ of AgNW solution on a (25 × 25) ㎟ substrate using the shear-coating method. It was also possible to align AgNWs in the drag direction by dragging the meniscus of the solution. The electro-optical properties of the AgNW thin film were adjusted by changing the experimental parameters that the amount of AgNWs suspension, the gap between the substrate and the blade, and the coating speed. As a result, AgNW thin films with a transmittance of 90.7 % at a wavelength of 550 nm and a sheet resistance of 15 Ω/□ was deposited and exhibited similar properties to similar AgNW transparent electrodes studied by other researchers.

• 공업화학
• /
• 제22권6호
• /
• pp.691-696
• /
• 2011

졸-겔 공정을 활용하여 유무기 하이브리드 형태의 투명 필름용 하드코팅층에 사용되는 코팅졸을 제작하였다. 콜로이드 실리카와 알콕시 실란{vinyltrimethoxy silane : (VTMS)와 [3-(methacryloyloxy)] propyltrimethoxysilane : (MAPTMS)}을 이용하였고 다양한 조건에 따라 실험을 실시하였다. 이 졸은 PMMA와 교반하여 PET필름에 코팅막을 형성하였다. 코팅막에 대한 특성은 여러 가지 측정에 의해 확인하였다. 코팅막은 PMMA 단독에 비해서 유기실란 양이 첨부된 형태에서 코팅막의 연필경도와 기재와의 부착력이 우수하였고 실험된 조건에서 시란의 양이 증가할수록 연필경도가 증가하는 경향이 나타났다.

• 공업화학
• /
• 제23권1호
• /
• pp.53-58
• /
• 2012

투명한 플라스틱 필름의 표면경도를 향상시키기 위하여 유-무기 하이브리드 코팅 용액을 졸-겔 공정을 이용하여 합성하였다. 무기성분으로 콜로이드 실리카와 유기성분으로 PMMA, 유-무기 성분 간의 결합력을 향상시켜 하이브리드 코팅 층의 특성을 더욱 향상시키기 위하여 실란커플링제로서 vinyl trimethoxy silane (VTMS)과 [3-(metha cryloyloxy)] propyl trimethoxy silane (MAPTMS)를 이용하였고, 알콕시 실란의 종류, 콜로이드 실리카/PMMA의 함량비 등의 반응조건에 따라 콜로이드 실리카/PMMA 졸을 합성하였다. 이러한 졸을 PET 필름에 바코팅시키고, 열경화 시켜 하드코팅막을 제조하여 물리적 화학적 특성을 조사하였다. PMMA에 비해서 하이브리드 형태에서 코팅 막의 연필경도와 기재와의 부착력이 우수하였다.

• 한국세라믹학회지
• /
• 제31권4호
• /
• pp.359-366
• /
• 1994

Tow types of supports were made using $\alpha$-Al2O3 powder and optimum conditions to prepare for supports were provided. Sol solution for coating was synthesized by sol-gel method with aluminum isopropoxide. Supports were coated and heat-treatemented, where the thickness of coating layer was controlled by dipping time. Flux and permeability of alumina membrane were measured by liquid and gas filtration apparatus and these were compared with the provided model. It was confirmed that the coating was done very well without micro~crack and defect.

• 한국인쇄학회지
• /
• 제9권1호
• /
• pp.1-11
• /
• 1991

In this reseach, double-layered photoconductor consist of the carrier generation layer(CGL) of $\varepsilon$ type copper phthalocyanine thin film by an aqueous coating method and the carrier transport layer(CGL) of polyvinyl carbazol(PVK) by spin coating. We inverstigated effect of the surfactant solution and cathod electrolysis to the crystal type of $\varepsilon$-CuPc in CGL with TEM, SEM and X- ray diffraction spectroscopy and studied the mechanism of an aqueous coating for the preparation of CGL. The effect of the washing of CGL about the electrophotographic characteristics of the $\varepsilon$-CuPc/PVK doublelayered photoconductors is studied also.