• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.5
• /
• pp.551-559
• /
• 2008

An experimental study was carried out to evaluate the potential of flotation process for the secondary clarifier of an activated sludge process. Flotation techniques, applied in this study, include electrofloation (EF) which generated fine bubbles smaller than $35{\mu}m$ in average and diffuser flotation (DF) which generated fine bubbles smaller than $55{\mu}m$ in average. The batch experiments were done with activated sludge displaying various characteristics. It was shown that the efficiency of solids/liquid separation was reduced as the diluted sludge volume index ($DSVI_{30}$) of activated sludge increased. The dependency, however, gradually decreased as the gas to solids (G/S) ratio increased. Thickening efficiency of EF was more than 2~10 times and DF process was more than 1.5~5 times as compared with gravity sedimentation (GS). Stable sludge blanket was maintained regardless of sludge settleability when the G/S ratio was 0.019 in the EF. On the other hand, Serious deterioration in the sludge blanket was observed in the DF depends on G/S ratio and sludge settleability. And For EF and DF, the suspended solids concentration of effluent was not nearly influenced on settleability of activated sludge and more clear than GS. A biological nutrient removal (BNR) process, combined with EF as a secondary clarifier was operated for three months. The mean MLSS (mixed liquid suspended solids) concentration in the reactor and mean solids concentration of return sludge were estimated to be 5,340 mg/L and 16,770 mg/L, respectively. The water quality of effluent was considerably stable and low value was accomplished, that was, standard suspended solids concentration $0.07{\pm}0.51mg/L$ and standard turbidity $1.44{\pm}0.56NTU$. The EF could be applicable for enhancement of efficiency of activated sludge system as well as improvement of the water quality of effluent.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.198-204
• /
• 2010

Solids flow characteristics have been determined in a pressurized solids recycle systems of silica sand particles for the application in a pressurized CFB(PCFB). The solids recycle system is composed of a downcomer(0.10 m i.d. 2.25 m high) and a loop-seal(0.10 m i.d.). The silica sand($d_p=240{\mu}m$, ${\rho}_s=2582kg/m^3$) particles were transported at room temperature and system pressure($P_{sys}$) up to 0.71 MPa using air. Solids mass flux($G_s$) increases with increasing system pressure at constant aeration rate. Pressure gradient, solids velocity and actual gas velocity increase with increasing $P_{sys}$ at constant aeration rate. The Pressure drop number($\Phi$) on pressure gradient in downcomer has been correlated with Transportation number(Tr). Pressure drop across the loop-seal increases with increasing of $G_s$ irrespective of variation of $P_{sys}$. The obtained $G_s$ and Transportation number(Tr) have been correlated with the experimental variables.

• Animal Bioscience
• /
• v.37 no.6
• /
• pp.1031-1040
• /
• 2024

Objective: This study aimed to evaluate the effect of feeding milk replacer (MR) with varying levels of lactose and the increased supply of total solids (from 750 to 960 g/d) on performance, blood metabolites, and health of Holstein male calves during the preweaning period. Methods: Forty newborn Holstein calves (10 per treatment) were blocked according to birth weight and date of birth and distributed in a randomized block design to different liquid diets: Whole milk powder (WMP) diluted to 125 g/L solids; MR with 48% lactose (48L), diluted to 125 g/L solids; MR with 53% lactose (53L), diluted to 125 g/L solids; 53L MR corrected to 160 g/L solids (16TS) by the inclusion of a solid corrector. Calves were individually housed in wood hutches, fed 6 L/d of the liquid diet, and had free water and starter concentrate access. The study lasted 56 days. Results: Liquid diet intake was higher for calves fed 16TS than for other treatments. Calves fed 16TS presented higher protein and fat intake, followed by those fed WMP and the 48L or 53L MRs. Lactose intake was higher for 16TS-fed calves, followed by 53L, 48L, and WMP-fed calves. Starter and total dry matter intake did not differ among liquid diets. The average daily gain was higher for 16TS than 48L-fed calves, with the other treatments being intermediary. The lowest feed efficiency was observed for calves fed 48L. No effects on health were observed, as well as on selected blood metabolites, except for albumin concentration, which was higher for calves fed 16TS and WMP. Conclusion: Higher total solids content (160 g/L) in MR increases nutrient intake and consequently improves the performance of dairy calves. Feeding MRs with levels of lactose up to 53% of the DM had no deleterious effect on the performance or health of the calves.

• Carbon letters
• /
• v.19
• /
• pp.107-111
• /
• 2016

• Journal of Environmental Health Sciences
• /
• v.22 no.2
• /
• pp.83-89
• /
• 1996

In order to evaluate the air quality, dry and wet deposition samples were collected by deposit containers during four months in Inchon area. The samples were analyzed for its solid composition and trace elements(Ca, Cd, Cu, Fe, Mn, Ni, Pb, Zn). The main results are summarized below 1. The amounts of dry and wet deposition in Inchon area were 1.06~3.14 ton/$km^2$/month, and affected by the rainfall and suspended yellow sand. 2. Through the analysis of solid balance, we found that 50% of total solids(TS) was fixed suspend ed solids(FSS), 25% was fixed dissolved solids(FDS), and each of volatile suspended solids(VSS) and volatile dissolved solids(VDS) accounted for 12.5%. 3. The amounts collected by sampler for trace elements were 938 ~ 2,765 $\mu g$ calcium/10days sampler, 0.2 ~ 90.4 $\mu g$ cadmium/10days/sampler, 26 ~ 298 $\mu g$ copper/10days/sampler, 928 ~ 3,939 $\mu g$ iron/10days/sampler, 50 ~ 202 $\mu g$ manganese/10days/sampler, 4 ~ 37 $\mu g$ nickel/10days/sampler, 52 ~ 406 $\mu g$ lead/10days/sampler, and 97 ~ 1,317 $\mu g$ zinc/10days/sampler, respectively. 4. Using the manganese analysis, it was found that 76.1% of TS was from soil.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.3
• /
• pp.121-127
• /
• 2011

This study used two types of rheology modifiers including an alkali-swellable emulsion (ASE) and an surface-adhesion emulsion (SAE) to elucidate their effects on high shear viscosity and dynamic penetration behavior among the flow properties of high solids coating. Since rheology under high shear and dynamic penetration behavior significantly affect the quality of coated paper in case of high solids coating, it is very important to examine the variations in rheology of high solids coating color by rheology modifier. It was found that the high solids coating color prepared with the SAE type showed superior dynamic penetration behavior and high shear viscosity than that with the ASE type rheology modifier.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.04a
• /
• pp.80-92
• /
• 2003

The water retention of coating colors can be accurately measured by devices such as an AA-GWR water retention meter whose principle of measurement is based on pressure filtration of coatings under an externally applied air pressure over a certain period of time. It was hypothesized that such devices could be also used to determine the immobilization solids(IMS) of coating colors by determining a sudden drop in the rate of dewatering, that is, a sudden change in the drainage curves. To test this hypothesis, the immobilization solids of coating colors containing various thickeners and water retention additives at different levels were first accurately measured by a modified immobilization tester based on the well-known gloss drop method, and then their values were compared with those obtained by an AA-GWR water retention tester. They agreed very well and showed that the mean of the solids differences is 0.36% in the IMS points between both methods. This good agreement was not surprising because both test methods are based on the same end-point, that is, the immobilization solids point at which menisci begin to form at the coating surface. Theoretical considerations supporting this new method for measuring the immobilization solids of coating colors are presented and some recommendations for the test method are discussed. Also, the effect of various thickeners and water retention additives on the properties and printability of coated papers is discussed.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.2
• /
• pp.155-160
• /
• 2005

Gravity thickening process has been widely used in WTP sludge thickening at domestic water treatment plant. The operation method of the process is very simple, however, the process requires long detention time about 24~48 hours for sludge thickening, uses polymer, and low total solids of thickened sludge to increase sludge thickening efficiency. To solve there problems, we studied about flotation process, especially, electro-flotation (EF) process in WTP sludge thickening. Electro-flotation process is simpler than dissolved-air-flotation(DAF) process because EF needs only electrode and current to generate micro-bubbles and the operation is easy. This study was performed at two batch columns to compare interface height, total solids, effluent turbidity between an electro-flotation thickening and a gravity thickening. According to the result, an electro-flotation thickening was that interface height was decreasing, total solids had high concentration, and effluent turbidity was low in comparison with a gravity thickening. Also, it will make the high efficiency of following process, such as a dehydrating process and digestive process. because of high total solids and low moisture content in the sludge.

• Journal of the Optical Society of Korea
• /
• v.19 no.3
• /
• pp.272-276
• /
• 2015

The PbS quantum dot is an emerging photovoltaic material, which may provide high efficiency breakthroughs. The most crucial element for the high efficiency solar cells's development is to understand charge transport characteristics of PbS quantum dot solids, which are also important in planning strategic research. We have investigated charge transport characteristics of PbS quantum dot solids thin films using space charge limited conduction analysis and assessed thickness dependent photovoltaic performances. The extracted carrier drift mobility was $low-10^{-2}cm^2/Vs$ with the estimated diffusion length about 50 nm. These and recently reported values were compared with those from a commercial photovoltaic material, and we present an essential element in further development of PbS quantum dot solids materials.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.42-47
• /
• 1989

The thermal behaviour of layerd solids, typified in practice by surface coated materials, is evaluated for the specific case of a fast moving heat source. This is intended to represent the particular instance of solids in sliding contact and the consequences of friction. The finite difference method has been utilised to establish the temperature distributions at the surface and also the sub-surface region for coating materials which are either less conductive or more conductive than the substrate to which they are attached. The effects of variation in layer thickness, and also the load, speed and friction coefficient, are evaluated.