• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1729-1731
• /
• 2003

Recently many solid-state laser systems were widely used in the medical applications. So it is necessary to study various optimal laser parameters for adopting new medical treatments. Alexandrite laser using switching mode power supply has designed and experimented to adjust a pulse repetition rate by PIC one-chip microprocessor. The fundamental results have been obtained during the first financial year in 2002. We will be able to find out the optimal hair removal characteristics by the repetitive experiments of Alexandrite laser as the parameters such as pulse repetition rate, pulse width, and pulse energy etc.

• Current Optics and Photonics
• /
• v.3 no.3
• /
• pp.243-247
• /
• 2019

We have developed a compact, wavelength-selectable, Q-switched Nd:YAG laser at mid ultraviolet for chemical warfare agent detection. The fundamental wave at 1064 nm is delivered by a pulsed solid state laser incorporating with a square-type Nd:YAG rod in a resonator closed by two crossed Porro prisms for environmental reliability. The output energy at 213 nm ($5{\omega}$) and 266 nm ($4{\omega}$) by ${\chi}^{(2)}$ process in the sequentially disposed BBO crystals are measured to be 6.8 mJ and 15.1 mJ, respectively. The output wavelength is selected for $5{\omega}$ and $4{\omega}$ by a motorized wavelength switch. The energy ratio of the $5{\omega}$ to the $4{\omega}$ is varied from 0.05 to 0.85 by controlling the phase matching temperature of the nonlinear crystal for sum-frequency generation without change of the output pulse parameters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.197-197
• /
• 2009

We have investigated the holographic grating formation on Ag-doped amorphous chalcogenide AsGeSeS thin films with Ag thickness. Holographic gratings have been formed using Diode Pumped Solid State laser (DPSS, 532.0nm) under [P:P] polarized the intensity polarization holography. The diffraction efficiency was obtained by +1st order intensity.

• Journal of the Korean Ceramic Society
• /
• v.56 no.4
• /
• pp.331-339
• /
• 2019

While high-temperature ceramic composites consisting of carbides, borides, and nitrides, the so-called ultra-high-temperature ceramics (UHTCs), have been commonly produced through solid-state sintering, melt-solidification is an alternative method for their manufacture. As many UHTCs are binary or ternary eutectic systems, they can be melted and solidified at a relatively low temperature via a eutectic reaction. The microstructure of the eutectic composites is typically rod-like or lamellar, as determined by the volume fraction of the second phase. Directional solidification can help fabricate more sophisticated UHTCs with highly aligned textures. This review describes the fabrication of UHTCs through the eutectic reaction and explains their mechanical properties. The use of melt-solidification has been limited to small specimens; however, the recently developed laser technology can melt large-sized UHTCs, suggesting their potential for practical applications. An example of laser melt-solidification of a eutectic ceramic composite is demonstrated.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.11
• /
• pp.29-34
• /
• 1995

Mirror coating is applied to laser facets to improve properties of edge emitting laser diodes. In this experiment, InGaAsP/GaAs high power laser diodes were studied with respect to different degrees of anti-reflective coating. Sputterred $Al_{2}$O$_{3}$ was used as the coating material and the HR coating was kept constant at 90%. Threshold current density, differential quantum efficiency, emission wavelength and the operating current at 500mW were measured for a range of AR coating and compared with theoretically calculated values; that showed good agreements. Precise wavelength control is important for laser diodes for solid state pumping because of small absorption bandwidth. In addition, since these lasers operate under CW condition, a lowest possible operating current for a given power is desired in order to minimize the heat produced. From the results of this experiment, we were able to obtain a optimum range of AR coatings for minimum operating current. The wavelength can be varied up to 4nm within this range.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1992.02a
• /
• pp.3-10
• /
• 1992

pphotostimulated desorpption of NO chemisorbed on ppt(001) at 80K has been studied by the (1+1)-resonance-enhanced multipphoton ionization((1+1)-REMppI) technique. A linearly ppolarized ArF excimer laser ( =193 nm, 6.41eV) is used as the ppumpp laser. A high adsorpption rate selectivity was found in the expposure deppendence of the NO desorpption yield. The NO desorpption yield increases drastically when the amount of NO expposure exceeds ~1.8 L. This result shows that the amount of NO sppecies with a large cross section for pphotostimulated desorpption increases drastically at higher NO coverages. Using scanning tunneling microscoppy, we have observed structural modifications of the chlorinated Si(111)-7$\times$7 surface induced by 266nm laser irradiation. At very low laser fluence of 0.7mJ/$\textrm{cm}^2$, at which thermal desorpption can be ignored, a pperiodic stripped ppattern of a single domain is imaged. This ppattern consists of flat terraces and narrow grooves of ~60 and ~10A in width, resppectively.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.68-69
• /
• 2009

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.326-327
• /
• 2004

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.10a
• /
• pp.379.2-379
• /
• 1999

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.10a
• /
• pp.382.1-382
• /
• 1999