• Nuclear Engineering and Technology
• /
• v.7 no.3
• /
• pp.213-222
• /
• 1975

Immobilization of the second-cycle radioactive liquid wastes from a Purex process was developed with the blown asphalt (manufactured by Kukdong Shell Oil Company Ltd) to eliminate the possibility that the radioactive materials will be redispersed into the environment. Attempts to incorporate these wastes directly into the asphalt martrices without any pretreatment were not successful, as it was observed that the sulphuric acid in the waste oxidised the asphalt. Hence, the waste was treated with caustic soda and made alkaline prior to bituminization, so that it was found that this pretreatment made the waste compatible to the asphalt matrices. The pure blown asphalt samples irradiated with doses of 4.0$\times$10$^{7}$ rad showed no evidence of volume increase. The suitable temperature for incorporation of the alkaline wastes into blown asphalt was 180-20$0^{\circ}C$. The Products containing 50 wt% salts represented the following good properties viz., volume reduction (about 1.4), homogeneity, teachability etc. During the period of 131 day $s^{l37}$Cs from products containing 40wt% salts was leached at rates ranging from 2.70$\times$10-4 to 8.27$\times$10-4g/cm2_day but the rate for $^{90}$ Sr was lower by one to two orders of magnitude by distilled water. The leaching rates for $^{137}$ Cs and $^{90}$ Sr by sea water were slightly lower than by distilled water. Both of the leaching rates decreased with increasing pH.H.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.11a
• /
• pp.68-68
• /
• 2001

Thin films of polycrystalline silicon (poly-Si) is a promising material for use in large-area electronic devices. Especially, the poly-Si can be used in high resolution and integrated active-matrix liquid-crystal displays (AMLCDs) and active matrix organic light-emitting diodes (AMOLEDs) because of its high mobility compared to hydrogenated _amorphous silicon (a-Si:H). A number of techniques have been proposed during the past several years to achieve poly-Si on large-area glass substrate. However, the conventional method for fabrication of poly-Si could not apply for glass instead of wafer or quartz substrate. Because the conventional method, low pressure chemical vapor deposition (LPCVD) has a high deposition temperature ($600^{\circ}C-1000^{\circ}C$) and solid phase crystallization (SPC) has a high annealing temperature ($600^{\circ}C-700^{\circ}C$). And also these are required time-consuming processes, which are too long to prevent the thermal damage of corning glass such as bending and fracture. The deposition of silicon thin films on low-cost foreign substrates has recently become a major objective in the search for processes having energy consumption and reaching a better cost evaluation. Hence, combining inexpensive deposition techniques with the growth of crystalline silicon seems to be a straightforward way of ensuring reduced production costs of large-area electronic devices. We have deposited crystalline poly-Si thin films on soda -lime glass and SiOz glass substrate as deposited by PVD at low substrate temperature using high power, magnetron sputtering method. The epitaxial orientation, microstructual characteristics and surface properties of the films were analyzed by TEM, XRD, and AFM. For the electrical characterization of these films, its properties were obtained from the Hall effect measurement by the Van der Pauw measurement.

• Current Photovoltaic Research
• /
• v.11 no.1
• /
• pp.8-12
• /
• 2023

In this work, we investigated the thickness of Ag precursor layer to improve the performance of flexible CIGSe solar cells grown on stainless steel (STS) substrates through three-stage co-evaporation with Ga grading followed by alkali treatments. The small amount of incorporated Ag in CIGSe films showed enhancement in the grain size and device efficiency. With an optimal 6 nm-thick Ag layer, the best cell on the STS substrate yielded more than 16%, which is comparable to the soda-lime glass (SLG) substrate. Thus, the addition of controlled Ag combined with alkali post-deposition treatment (PDT) led to increased open-circuit voltage (VOC), accompanied by the increased built-in potential as confirmed by capacitance-voltage (C-V) measurements. It is related to a reduction of charge recombination at the depletion region. The results suggest that Ag alloying and alkali PDT are essential for producing highly efficient flexible CIGSe solar cells.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.6
• /
• pp.715-721
• /
• 2007

Residual calcium concentration is high, in general, at the effluent of the fluoride removal process in the electronics industry manufacturing semiconductor and LCD. To increase the stability of the membrane process incorporated for reuse of wastewater, the residual calcium is required to be pre-removed. Hyperkinetic Vortex Crystallization(HVC) process was installed in the electronics industry manufecturing semi conductor as a pilot scale for accelerating calcification of calcium ion. Compared to the conventional soda ash method, the 31% higher calcium removal efficiency was achieved when HVC was applied at the same sodium carbonate dosage. In order to maintain the economic calcium removal target of 70% preset by manufacturer, the dosing concentration of the soda ash was 530 mg/L based on influent flowrate. The seed concentration in the reactor was one of the critical factors and should be maintained in the range of $800\sim1,200mg$ SS/L to maximize the calcium removal efficiency. The calcite production rate was 0.30 g SS/g $Na_2CO_3$ in the average. The economic HVC passing time of the mixture was in the range of $2\sim5$ times. Relatively, stable calcium concentration was maintained in the range of $30\sim72$ mg/L(average 49 mg/L) although the calcium concentration in the feed was severely fluctuated with $74\sim359$ mg/L(average 173 mg/L). The HVC process was characterized as environment-friendly technology reducing chemical dosage and chemical sludge production and minimizing maintenance cost.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.10
• /
• pp.1225-1233
• /
• 2017

The aim of this study was to evaluate the microbial inhibitory activity and physicochemical quality of fresh carrot juice prepared with different environmentally-friendly washing methods during low temperature storage. Individual and combined treatments with sodium bicarbonate (baking soda, $NaHCO_3$) and citric acid were applied to carrots for 10 min. Tap water and 50 ppm of sodium hypochlorite (NaOCl) were used as the control. Combined treatment of 1% $NaHCO_3$ and 1% citric acid significantly reduced total aerobic counts and coliforms. In addition, combined treatment of 1% $NaHCO_3$ and 1% citric acid inhibited microbial growth for 7 days at $4^{\circ}C$ and $10^{\circ}C$ in a shelf-life study. There were no significant differences among the sanitizers in terms of $^{\circ}Brix$, acidity, pH, and color. Changes in physicochemical quality were not significantly different by sanitizer but were affected by storage temperature. These results indicate that washing with combined treatment of 1% $NaHCO_3$ and 1% citric acid is an effective method to inhibit the microbial population and maintain physicochemical quality. Therefore, combined treatment of 1% $NaHCO_3$ and 1% citric acid can be effectively used to sanitize and prepare carrot juice without affecting other properties.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.3
• /
• pp.7-15
• /
• 1981

A Japanese larch has been reforested very much in Korea, but it is not used as a wood resources for paper pulp by now. So this study is carried out to utilize the larchwood for paper pulp manufacture through the Asplund pulping process. The experiment on increasing in the brightness of the pulp is made through the addition of $MgSO_4$, $ZnSO_4$, $Al_2(SO_4)_3$, and KI as a cellulose stabilizer in chip treatment with caustic soda which is followed by high-temperature defibration and conventional peroxide bleaching (5% NaOH plus 2% additive salt per wood in cold pretreatment), or in high-consistency (30%) pulp bleaching of hydrogen peroxide and peracetic acid (100% acitve oxygen per lignin) for conventional one. The results obtained are as follows: 1. The solution of 0.5% additive salts had different pH by the sort of bases that was pH 5.7 in $MgSO_4$, liquor, pH 4.9 for $ZnSO_4$, and pH 2.9 for $Al_2(SO_4)_3$, and in the precepitation of bases which ranged to pH 6-13 for $MgSO_4$, pH 5-12 for $ZnSO_4$, and pH 3-10 for $Al_2(SO_4)_3$. 2. The cellulose stabilizer affective in high-consistency peroxide bleaching was KI, $MgSO_4$, and $ZnSO_4$, but has made a little improvement in de lignification and brightness of pulp in comparison with no addition. 3. The higher alkalinity in the chip treatment has made the higher strength and brightness of larchwood Aspiund pulp instead of downing the pulp yield. And the effective compound for cellulose stabilizer in caustic soda pretreatment of chip was $ZnSO_4$, $Al_2(SO_4)_3$ and KI in order for the conventional peroxide bleaching after Asplund pulping. 4. Therefore, the more effective additives for cellulose stabilization in high-temperature defibration of larchwood suppose to be $ZnSO_4$, $Al_2(SO_4)_3$, and KI, while KI and $MgSO_4$ for peroxide bleaching.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.4
• /
• pp.66-83
• /
• 2018

This article focuses how the materials of hatstrings of the 19th to 20th century gat, the Korean top hat for men among the collections of National Folk Museum of Korea, was transformed after port opening treaties with overseas since 1876. As a result of analyzing the materials of the hatstrings, amber, tortoiseshell, wood and bamboo as the traditional materials were used, and ivory, glass (soda glass, lead glass, alkali mixed glass) and plastics (cellulose nitrate, phenol-formaldehyde, polystyrene, acryl) were newly used for the hatstrings. Bamboo, wood and amber were the most frequently used materials. Bamboo was mainly used for the pipe of hatstring and were combined with beads and central decorations of other materials. This shows the trend of bamboo hatstring according to the simplification of the clothing and the culture by Regent Heungseon Daewongun. Ambers were used in the central decorations and beads and the origin of ambers was baltic amber just like the amber relics found in Korea. Compositions of glass were soda glass and alkali mixed glass which were excavated or handed down in Korea from ancient times to Joseon dynasty. But in the case of lead glass, Na2O was detected and it is considered to be a new type lead glass for crafts which came from overseas after port opening since 1876 because it showed the characteristic that it deviates from the lead glass component found in Korea. Plastics such as cellulose nitrate and phenol-formaldehyde were used as new synthetic materials to replace traditional materials such as tortoiseshell, amber, and coral as in the West. Cracks, crazing, crumbly and yellowing of cellulose nitrate of hatstrings were observed by deterioration. The survey of the materials of the 19th to 20th century hatstrings among the collections of National Folk Museum of Korea showed that the introduction of new materials such as glass and plastics were used to replace natural materials such as tortoiseshell and amber along with the use of traditional materials after port opening since 1876.

• Journal of the Korean Chemical Society
• /
• v.12 no.2
• /
• pp.65-80
• /
• 1968

The physico-chemical properties of nine selected thallium borosilicate glasses and other 21 supplementary compositions were investigated. Their composition-property curves are found to be in many respects analogous to those of other borosilicate glasses containing lithia, soda, and lead oxide. It is indicated that certain minima found in the composition-property curves of thallium borosilicate glasses might be caused by a change in boron coordination as has been observed to occur in the $Na_2O-B_2O_3-SiO_2$ glasses. Typical effects of thallium ions on the borosilicate glass are summarized as follows: 1) Addition of thallium ions increased density, refractive index, water solubility, linear coefficient of thermal expansion, and dielectric constant. 2) Increased concentration of thallium decreased the softening point of the glasses, caused fluorescence under ultraviolet radiation and smeared out the absorption edges up to $15{\mu}$ in the infrared region. An extensive liquid immiscibility was found by replication electron microscope technique in the $Tl_2O-B_2O_3-SiO_2$ system. The immiscibility covers a composition range roughly from 55 wt. % Tl2O to the binary system $B_2O_3-SiO_2.$ By acid treatment, it was found that the immiscible glass consists of separate silica-rich and boron-rich phases.

• Journal of dental hygiene science
• /
• v.11 no.3
• /
• pp.205-211
• /
• 2011

The present study seeks to find the effect of oral health status that parents recognized, oral health habit and food intake on existence of decalcified teeth and decayed teeth. Participants were 293 infants aged 18-24 months who visited C dental clinic in Kyungki province between January and December 2010. Questionnaires and oral exam results were used and statistically analyzed by the SPSS program. Fisher's Exact and chi-square test were used to analyze the data. The 18-20 month-old age group had the highest rate of decalcified teeth with 36.4% while the 23-24 month-old age group had the highest rate of decayed teeth with 37.0%. Bottle feeding showed correlation with decalcified teeth, and decayed teeth. Parents were able to recognize decayed teeth and decalcified teeth. Group 2 food(soda/soft drinks/sugared fruit juice) was related to decalcified teeth and decayed teeth(p<.001). Group 4 food (cake/cookies/doughnut/dried fruit/banana) and group 5food(caramel/candy/chocolate bar) were both related to decalcified teeth(p<.001). As the result of dental examination, dental treatment was highly needed for the 21-22 month-old age group(89.3%), and preventive treatment and plaque control were highly needed for the 18-20 month-old age group(94.5%). The results concluded that 18-24 months was the critical period for children's oral health, therefore organized oral health education for parents is necessary.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.78.2-78.2
• /
• 2010

Cu(In,Ga)Se2 (CIGS)박막태양전지는 간단한구조와 가격경쟁력 및 고효율화 가능성에 대한 기대감에 의해 많은 연구가 수행되어오고 있다. 특히 높은 흡수계수와 적절한 밴드갭, 큰 결정크기와 같은 물질의 특성들이 장점으로 작용하고 있기 때문이다. 또한 CIGS박막태양전지는 다른 태양전지에 비해 광열화가 적다는 장점도 가지고 있다. CIGS 박막은 CuInSe2내의 In 사이트에 Ga을 도핑함으로서 형성이 되는데 그때의 밴드갭은 약 1.4eV이며 이를 형성하기 위해 많은 방법들이 제안되고 있는데, CIGS박막 형성 시 가장 중요시 여겨야 될 인자는 구성원소로부터 최적화된 조성비를 찾는 것이다. 이러한 관점에서 볼때 evaporation법이나 sputtering법같은 진공방식의 공정법이 비진공방식에 비해 최적의 조성비를 찾는 것이 수월할 것으로 생각된다. selenization을 하기전에, 동시증착이나 다층박막형성을 통해 Cu-In-Se의 조합이 일반적으로 이루어진다. 어떤방법이든 Se의 부가적인 공급이 이루어지는데 시작 전구체의 조합에서 그 해법을 제시하는 것에 대한 논의가 많이 부족한 현실로서, CuInSe2의 단일전구체에 의한 박막형성과 특성평가에 대해 구체적인 논의가 필요하다. 본 실험에서는 Cu-In-Se 전구체를 CuInSe2 단일 타겟에서부터 RF 마그네트론 스퍼터링법을 이용하여 박막증착을 하여 Se의 Rapid Thermal Process(RTA)법을 통해 Se이 순차적으로 공급되었다. 이때 형성되는 박막의 태양전지 흡수층 적용을 위한 광학적, 전기적 및 구조적에 대한 논의된다. Soda lime glass(SLG)와 Corning 1737 유리를 기판으로 하여 아세톤-에탄올을 이용, 초음파세척을 실시하였다. 스퍼터 공정을 하기전에 흡착된 물분자를 제거하기 위하여 약 30분간 $120^{\circ}C$로 열을 가해주었으며, 공정을 위한 총 아르곤 가스의 양은 약 50sccm이며 이때의 공정압력은 20mtorr로 고정하였다. 우선 RF power와 기판온도에 따른 단일전구체 형성을 관찰하기 위하여 각각 30~80W, RT~$400^{\circ}C$로 변화를 주어 박막을 형성한 후 모든 sample에 대하여 $500^{\circ}C$분위기에 effusion cell을 이용하여 Se 분위기에서 결정화를 실시하였다. 샘플의 두께는 Surface profiler로 측정하였고 단면은 전자주사현미경으로 관찰되었다. 동시에 SEM이미지를 통하여 morphology와 grain size 및 EDX를 통하여 조성분석을 하였다. 밴드갭, 투과율 및 흡수계수는 UV-VIS-NIR분광분석법을 통하여 수행되었으며, 전기적 특성분석을 위해 4-point-probe와 Hall effect측정을 수행하였다. 공정변수에 따른 단일타겟으로 얻어 결정화된 CuInSe2박막의 자세한 결과와 논의에 대하여 발표한다.