• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.28-35
• /
• 2014

High-efficiency in $Cu(In,Ga)Se_2$ (CIGS) solar cells were usually achieved on soda-lime glass substrates due to Na incorporation that reduces deep-level defects. However, this supply of sodium from sodalime glass to CIGS through Mo back electrode could be limited at low deposition temperature. Na content could be more precisely controlled by supplying Na from known amount of an outside source. For the purpose, an $Na_2S$ layer was deposited on Mo electrode prior to CIGS film deposition and supplied to CIGS during CIGS film. With the $Na_2S$ underlayer a more uniform component distribution was possible at $350^{\circ}C$ and efficiency was improved compared to the cell without $Na_2S$ layer. With more precise control of bulk and surface component profile, CIGS film can be deposited at low temperature and could be useful for flexible CIGS solar cells.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.6
• /
• pp.303-307
• /
• 2015

Multilayered films of ITO (In₂O₃:SnO₂ = 9:1)/SiO₂ were deposited on soda-lime glass by RF/DC magnetron sputtering at 500℃ to improve the energy conversion efficiency of dye-sensitized solar cells (DSSCs). The light absorption of the dye was improved by decrease in light reflectance from the surface of the DSSCs by using an ITO film. In order to estimate the optical characteristics and compare them with experimental results, a simulation program named EMP (essential macleod program) was used. EMP results revealed that the multilayered thin films showed high transmittance (approximate average transmittance of 79%) by adjusting the SiO₂ layer thickness. XRD results revealed that the ITO and TiO₂ films exhibited a crystalline phase with (400) and (101) preferred orientations at 2 θ = 26.24° and 35.18°, respectively. The photocurrent-voltage (I-V) characteristics of the DSSCs were measured under AM 1.5 and 100 mW/cm² (1 sun) by using a solar simulator. The DSSC fabricated on the ITO film with a 0.1-nm-thick SiO₂ film showed a Voc of 0.697 V, J_sc of 10.596 mA/cm² , FF of 66.423, and calculated power conversion efficiency (η_AM1.5) of 5.259%, which was the maximum value observed in this study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.245-245
• /
• 2015

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. 특히 CIGS 태양전지에서는 Na의 역할이 매우 중요한데 유연기판의 경우 이러한 Na이 없을 뿐만 아니라 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 또한 플라스틱기판의 경우 내열성이 낮아 저온에서 공정을 진행해야하는 단점이 있다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 유연기판으로 STS 430 stainless steel과 poly-imide를 이용하여 특성 개선을 진행하였다. 먼저 stainless steel과 Poly-imide, soda-lime glass, coning glass의 기판을 이용하여 기판에 따른 흡수층의 특성을 비교 분석하였으며 stainless steel 기판을 이용하여 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 이때 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.6%로 증가하였다. 또한 poly-imide 기판을 이용하여 $400^{\circ}C$이하에서 흡수층을 제조하여 특성평가를 진행하였으며 소자 제조 후 효율은 약 12.2%를 달성하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.613-618
• /
• 2009

We designed new compositions for lead free and low temperature sealing glass frit of $ZnO-V_2O_5-P_2O_5$ system, which can be used for PDP (Plasma Display Panel) or other electronic devices. The $ZnO-V_2O_5-P_2O_5$ system can be used as a sealing material at temperatures even lower than 430$^{\circ}C$. This system, however, showed lower bonding strength with glass substrate compared to commercialized Pb based sealing materials. So, we added $TiO_2$ as a promoter for bonding strength. We examined the effect of $TiO_2$ addition on sealing behaviors of $ZnO-V_2O_5-P_2O_5$ glasses with the data for flow button, wetting angle, temporary & permanent residual stress of glass substrate, EPMA analysis of interface between sealing materials and glass substrate, and bonding strength. As a result, sealing characteristics of $ZnO-V_2O_5-P_2O_5$ system glasses were improved with $TiO_2$ addition, but showed a maximum value at 5 mol% $TiO_2$ addition. The reason for improved bonding characteristics was considered to be the chemical interaction between glass substrate and sealing glass, and structural densification of sealing glass itself.

• 전자공학회논문지 IE
• /
• v.44 no.2
• /
• pp.26-31
• /
• 2007

A surface treatment was performed after the screen printing of a carbon nanotube paste for obtaining the carbon nanotube field emission array(CNT FEA) on the soda-lime glass substrate. In this experiment, Ar ion bombardment was applied as an effective surface treatment method. After making a cathode electrode on the glass substrate, photo sensitive CNT paste was screen-printed, and then back-side was exposure by uv light. Then, the exposed CNT paste was selectively remained by development. After post-baking, the remained CNT paste was bombarded by accelerated Ar ions for removing some binders and exposing only CNTs. As results, the field emission characteristics were strongly depended on the accelerating energy. At 100 eV, the emission was highest and as the acceleration energy increases more then 100 eV, the emission decreased. This was due to the removal of CNT itself as well as binders.

• Journal of Environmental Science International
• /
• v.18 no.5
• /
• pp.509-515
• /
• 2009

The aim of this study is investigated greenhouse gas emissions of glass industry, and when calculates greenhouse gas emission, using formula(Tier 3) advising in IPCC(Intergovernmental Panel on Climate Change) and using self designed formula(Tier 3+) authors of this study. Studied to propose calculation formula that can compare these two calculation results and apply to domestic. Formula of Tier 3 calculated to theoretical composition of carbonate material, And Formula of Tier 3+ calculated on the basis of chemical substance formation table that get from glass manufacture company(The S company). As a result, Dolomite, Soda ash, Limestone, Industrial Barium carbonate is calculated value of Tier 3+ lower than value of Tier 3, And Industrial Potassium carbonate, Industrial Strontium carbonate was calculated value of Tier 3 lower than value of Tier 3. This study finding, formula of Tier 3+ has higher confidence than formula of Tier 3 when consider revision about purity of injection raw material. And hereafter, When calculate greenhouse gas emissions about nonmetallic mineral industry, use of Tier 3+ is considered that should be encouraged.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.5
• /
• pp.606-617
• /
• 2000

The purpose of this study was to measure the marginal fidelities and the fracture strength of IPS Empress $2^{(R)}\;and\;In-Ceram^{(R)}$ ceramic crowns. After constructed of 12 experimental dies for each group, ceramic crowns were fabricated on the metal master dies prepared on the maxillary right premolar Marginal gaps were measured on the specimen between the margin of each crown and finish-ing line of the metal master die by using stereo-microscope($SZ-ST^{(R)}$ Olympus, Japan) and all specimens were cemented on the metal master die with Bistite $II^{(R)}$ (Tokuyama soda Co, LTD., Japan) resin cement. Finally marginal gaps were measured again. To measure of the fracture strength, buccal incline on the functional cusp of specimens were loaded until the catastrophic failure occurred by using the AGS-1000 $D^{(R)}$(Shimadzu, Japan). The result of marginal fidelities and fracture strength were statistically analyzed with the SPSS version 8.0 programs. The results of this study were as follows : 1. No significant difference was found in the mean marginal fidelities and fracture strength between the IPS Empress $2^{(R)}\;and\;In-Ceram^{(R)}$. 2. In comparison of marginal fidelities between before and after cementation, there was significant difference(P<0.05). The IPS Empress 2 system was shown in this study that had good marginal fidelities and fracture strength compared to In-Ceram ceramics. Although this system was acceptable to clinical applications, the system still has to be considered long-term researches about marginal fidelities and fracture strength due to the lack of data about the clinical researches.

• Journal of the Korean Chemical Society
• /
• v.43 no.2
• /
• pp.172-181
• /
• 1999

To develop the manufacturing technique for the powder builder of amorphous solid types, the water glass mixed with caustic soda dispersed into the methanol. Thus soluble sodium silicate was made a form of amorphous solid powder. In order to examine characteristics of water soluble sodium silicate $SiO_2/Na_2O$ mol ratio, we investigated solubility, thermogram, SEM, and BET analysis. pH buffering capacity, calcium-ion binding capacity as temperature change, and surfactant loading capacity were examined for characteristics as laundry detergent builder. $SiO_2/Na_2O$ molar ratio of soluble sodium silicate was 1.0, 2.4, 2.8, and zeolite was used in order to investigate basic characteristics of laundry detergent builder. Silicate used with laundry detergent was good for pH buffering capacity and solubility. But calcium-ion binding capacity and surfactant adsorption ability were lower. $SiO_2/Na_2O$ mol ratio became higher, pH buffering capacity and ion exchange ability were lower and surfactant adsorption ability was a little higher.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.179-186
• /
• 1998

We have been investigated the effects of the initial pH of the aquous solution, reaction temperature and time for the flaking of the soda-lime glass container. Flaking of glass occuurred in the cases of the $121^{\circ}C$, above pH 11 of solution with no $Mg^{2+}$ ions in solution. The pH of the solution approached to pH 10 under the conditions of below pH 9 of start solution. The flaking mechanism of the glass seem to be composed of formation of leached layer of $Ca^{2+}$ and $Na^{2+}$ ion and separation of these layers during the cooling by the difference of thermal expansion between leached layer and glass surface. The leaching of alkali ions in glass depends on the pH condition of the start solution and the temperature. In the case of $Mg^{2+}$ ions are added, $Mg^{2+}$ ions accelerate the flaking of the sodalime glasses and forms the magnesium silicate compound which result in the decrease of the pH of the solution.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.237-242
• /
• 2006

Surfaces found in nature, including biological surfaces have been providing inspiration to modify/fabricate artificial surfaces as solutions for tribological applications. As an example, the concept of 'lotus-effect' has motivated tribologists world wide to modify/fabricate surfaces for enhanced tribological performance. These was done by creating nano/micro-scale asperities on various surfaces using ion beam milling and ion-beam assisted roughening. In order to understand the attributes of natural surfaces, which are inspirational to tribologists, we characterized the surface of two natural surfaces-Nelumbo nucifera (lotus) and Colocasia esculenta leaves. Further, we evaluated their micro-scale friction property, both in their fresh and dried conditions. The characterization of surfaces was conducted using a confocal microscope and SEM, which involved the evaluation of size and distribution of protuberances. The micro-scale friction property was evaluated using a ball-on-flat type micro-tribo tester, under reciprocating motion. A soda lime glass ball (2 mm diameter) was used in these tests. Tests were conducted at the applied normal load of $3000{\mu}N$, at a sliding speed of 1 mm/sec for a scan length of 3 mm. All experiments were conducted at ambient temperature ($24{\pm}1^{\circ}C}$) and relative humidity ($45{\pm}5%$). It was observed that the friction behaviour of the natural surfaces was influenced by their surface characteristics (morphology and distribution of protuberances) and also by the condition (fresh or dried) in which they were tested.