• 전력전자학회논문지
• /
• 제24권3호
• /
• pp.207-214
• /
• 2019

In this study, discrete-time domain analysis is proposed to investigate the input current of a buck AC/DC light-emitting diode (LED) driver. The buck power factor correction converter can operate in both discontinuous conduction mode (DCM) and continuous conduction mode (CCM). Two discontinuous and two continuous conduction operating modes are possible depending on which event terminates the conduction of the main switch in a switching cycle. All four operating modes are considered in the discrete-time domain analysis. The peak current-mode control with slope compensation is used to design a low-cost AC/DC LED driver. A slope compensation design of the buck AC/DC LED driver is described on the basis of a discrete-time domain analysis. Experimental results are presented to confirm the usefulness of the proposed analysis.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.98-99
• /
• 2017

A discrete time domain modeling for the current-mode-controlled buck LED driver is presented in this paper. Based on the modeling result, a root locus analysis for the buck LED driver with slope compensation is done to derive the stability boundaries of feedback gains.

• Journal of Electrical Engineering and Technology
• /
• 제10권5호
• /
• pp.1989-2000
• /
• 2015

In this paper, digital peak current mode control for single phase H-bridge inverters is developed and implemented. The digital peak current mode control is achieved by directly controlling the PWM signals by cycle-by-cycle current limitation. Unlike the DC-DC converter where the output voltage always remains in the positive region, the output of DC-AC inverter flips from positive to negative region continuously. Therefore, when the inverter operates in negative region, the control should be changed to valley current mode control. Thus, a novel control logic circuit is required for the function and need to be analyzed for the hardware to track the sinusoidal reference in both regions. The problem of sub-harmonic instability which is inherent with peak current mode control is also addressed, and then proposes the digital slope compensation in constant-sloped external ramp to suppress the oscillation. For unipolar PWM switching method, an adaptive slope compensation in digital manner is also proposed. In this paper, the operating principles and design guidelines of the proposed scheme are presented, along with the performance analysis and numerical simulation. Also, a 200W inverter hardware prototype has been implemented for experimental verification of the proposed controller scheme.

• 전력전자학회논문지
• /
• 제26권4호
• /
• pp.302-305
• /
• 2021

Selection of the optimal inductance for power factor improvement of a buck AC/DC light-emitting diode (LED) driver with wide input voltage range is described in this study. The power factor change based on the slope compensation is obtained for various normalized output current (NOC) values using discrete-time domain analysis. The possibility of implementing constant slope compensation is described using power factor curves for various NOC values. NOC = 0.5 is chosen for the value of inductance with consideration for the simple implementation and reduction of inductor size. Experimental results of the inductance corresponding to NOC = 0.5 are presented.

• 한국항행학회논문지
• /
• 제17권2호
• /
• pp.208-217
• /
• 2013

분산 제어 (DM; dispersion management)와 광 위상 공액 (optical phase conjugation)이 적용된 광전송 링크에서 중계 구간 당 잉여 분산 (RDPS; residual dispersion per span) 기울기 (slope)에 따른 파장 분할 다중 전송 (WDM; wavelength division multiplexed) 채널의 보상 특성을 분석하여 최적의 RDPS 기울기를 도출하였다. RDPS 기울기가 증가할수록 WDM 채널의 유효 입사 전력 범위를 더욱 증가시키고 채널 간 성능 차이를 더욱 감소시키는 것을 확인하였다. 아울러 RDPS 기울기가 증가할수록 유효 전체 잉여 분산 (NRD; net residual dispersion) 범위도 증가하여 큰 RDPS 기울기가 유연한 광전송 링크 구성에 더욱 유리하다는 것을 확인하였다.

• 대한원격탐사학회지
• /
• 제27권3호
• /
• pp.369-377
• /
• 2011

Since well-calibrated satellite data is critical for their applications, calibration and validation of COMS science data was one of the key activities during the IOT. COMS MI radiometric calibration process was divided into two phases according to the out-gassing of the sensor: calibrations of the visible (VI) and infrared (IR) channels. Different from the VIS calibration, the calibration steps for the IR channels followed additional processes to secure their radiometric performances. Primary calibration steps of the IR were scan mirror emissivity correction, midnight effect compensation, slope averaging and 1/f noise compensation after a nominal calibration. First, the scan mirror emissivity correction was conducted to compensate the variability of the scan mirror emissivity driven by the coating material on the scan mirror. Second, the midnight effect correction was performed to remove unreasonable high spikes of the slope values caused by the excessive radiative sources during the local midnight. After these steps, the residual (difference between the previous slope and the given slope) was filtered by a smoothing routine to eliminate the remnant random noises. The 1/f noise compensation was also carried out to filter out the lower frequency noises caused from the electronics in the Imager. With through calibration processes during the entire IOT period, the calibrated IR data showed excellent performances.

• 한국생산제조학회지
• /
• 제8권1호
• /
• pp.126-134
• /
• 1999

In this paper, a new error compensating technique for form-error compensation of rough-surface profile obtained by contact stylus profilometer is proposed. By the method, the real contact points of rough-surface and diamond stylus can be estimated and the measured profile data corrected. To verify the compensation effect, the properties(Ra, RMS, Kurtosis, Skewness) of measured profile data and compensated data were compared. And, the cumulative RMS slope was proposed to assess the compensated effect of upper area of profile. The results show that the measuring error could be compensated very well in amplitude parameters and in proposed cumulative RMS slope by the developed form-error compensating technique.

• 전력전자학회논문지
• /
• 제24권2호
• /
• pp.134-137
• /
• 2019

A wide-bandwidth current controller is required for fast charging/discharging of super capacitor applications. Peak current mode is generally used to accomplish fast charging/discharging because this mode has fast response characteristics. However, the peak current mode control must have a slope compensation function to restrain sub-harmonics oscillation. The slope must be changed accordingly if the controlled output voltage is varied. However, changing the slope for every changed output voltage is not easy. The other solution, selecting the slope as the maximum value, causes a slow response problem to occur. Therefore, we propose a hybrid mode controller that uses a peak current and a newly specified valley current. Through the proposed hybrid mode control, the sub-harmonic oscillation does not occur when the duty is larger than 0.5 because of the fast response.

• 전력전자학회논문지
• /
• 제23권2호
• /
• pp.147-151
• /
• 2018

Phase-shift fullbridge (PSFB) converter detects the current in the primary side for operation of the peak current mode controller (PCMC). The PCMC must used the slope compensation to solve the problem when the effective duty is over 0.5. The voltage response of PSFB converters has slower than that of buck converter because of slew interval even if the voltage controllers of two converters have same bandwidth. To overcome these problems, this work proposes a compensating method of current reference considering slew interval and fast response in the PSFB converter. The effectiveness of the proposed method is proven using the PSIM simulation and experiment.

• 한국광학회지
• /
• 제15권6호
• /
• pp.485-489
• /
• 2004

색 분산과 색 분산 경사를 보상하기 위하여 결합 계수가 파장 축을 따라 첩 된 순 위상 샘플링 광섬유 Bragg 격자를 제안하였다. 기존의 샘플링 주기의 첩과 결합 계수의 첩을 동시에 이용하여 동일한 파장 다중 채널들의 대역폭들을 얻을 수 있었다.