• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1795-1800
• /
• 2004

DOS and NaCl aerosol particles with geometric mean diameter of $0.1{\sim}3.0{\mu}m$ geometric standard deviation of $1.1{\sim}1.8$ and total number concentration of $450{\sim}400$ $particles/cm^3$ were used to determine collection efficiencies of a duct-type wet scrubber with respect to particle size. The tested operating variables included air velocity and water injection rate. It was shown from the experimental results that the collection efficiencies increased with increasing water injection rate and decreasing air velocity. It was also seen that the collection efficiency of the Duct-type wet scrubber is mainly governed by the mechanism of inertial impaction.

• Atmosphere
• /
• v.22 no.1
• /
• pp.87-96
• /
• 2012

Aerosol number concentration ($N_{CN}$), size distribution and cloud condensation nuclei (CCN) concentration ($N_{CCN}$) were measured during 16-21 August 2008 at Daegwallyeong (DG) located in the eastern rural region of the Korean Peninsula. In the very next week (22-29 August 2008) the same aerosol properties were measured at Yeongjong Island (YJ) in the Yellow Sea. $N_{CN}$ for all 3 size cuts (above 3, 6 and 10 nm) was significantly higher at DG than YJ, but $N_{CCN}$ was significantly lower at the former and resulted in the $N_{CCN}/N_{CN}$ ratio more than twice higher at YJ ($0.94{\pm}0.09$ vs. $0.35{\pm}0.15$ at 0.53% supersaturation). The geometric mean diameter at DG, $53{\pm}15nm$, was much smaller than that at YJ, $91{\pm}6nm$, due to the particle formation events that were likely to have occurred continuously at DG. For given mean diameter, aerosols were more likely to act as CCN at YG compared to those at DG.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1510-1515
• /
• 2004

The effects of additive ions on the generation of metallic nanoparticles were evaluated using a corona induced supersonic nozzle. Applying the corona discharge to the nanoparticle generator, a tungsten needle and the supersonic nozzle are used as an anode electrode and a cathode electrode respectively. The corona ions act as nuclei for the silver vapor condensation. The ion density was controlled precisely as varying the applied voltage between electrode and nozzle. The mean diameter of the silver particle decreases as the ion density increases. However, the number concentration of the silver particle tended to increase with the ion density. The size distribution is more uniform as the ion density increases.

• Journal of Environmental Science International
• /
• v.23 no.3
• /
• pp.447-457
• /
• 2014

The number concentrations, the mass concentrations and the elemental concentrations of $PM_{10}$ have measured at Gosan site in Jeju, Korea, from March 2010 to December 2010. And the correlation and the factor analysis for the number, the mass and the elemental concentrations of $PM_{10}$ are performed to identify their relationships and sources. The average $PM_{10}$ number concentration is observed $246\;particles/cm^3$($35.7{\sim}1,017\;particles/cm^3$) and the average $PM_{10}$ mass concentration is shown $50.1{\mu}g/m^3$($16.7{\sim}441.4{\mu}g/m^3$) during this experimental period. The number concentrations are significantly decreased with increasing particle size, hence the concentrations for the smaller particles less than $2.5{\mu}m$($PM_{2.5}$) are contributed 99.6% to the total $PM_{10}$ number concentrations. The highest concentration of the 20 elements in $PM_{10}$ determined in this study is shown by S with a mean value of $1,497ng/m^3$ and the lowest concentration of them is found by Cd with a mean value of $0.57ng/m^3$. The elements in $PM_{10}$ are evidently classified into two group based on their concentrations: In group 1, including S>Na>Al>Fe>Ca>Mg>K, the elemental mean concentrations are higher than several hundred $ng/m^3$, on the other hand, the concentrations are lower than several ten $ng/m^3$ in group 2, including Zn>Mn>Ni>Ti>Cr>Co>Cu>Mo>Sr>Ba>V>Cd. The size-separated number concentrations are shown positively correlated with the mass concentrations in overall size ranges, although their correlation coefficients, which are monotonously increased or decreased with size range, are not high. The concentrations of the elements in group 1 are shown highly correlated with the mass concentrations, but the concentrations in group 2 are shown hardly correlated with the mass concentrations. The elements originated from natural sources have been predominantly related to the mass concentrations while the elements from anthropogenic sources have mainly affected on the number concentrations of $PM_{10}$.

• Asian Journal of Atmospheric Environment
• /
• v.9 no.3
• /
• pp.205-213
• /
• 2015

The objective of the current study was to assess the comparative risk associated with exposure to particulate matter (PM) while commuting via different public transport modes in Fukuoka, Japan. For the given routes and measuring days, a trip-maker carried a lightweight portable bag loaded the real-time measurement devices which take simultaneous measurement for size-fractioned particle number concentration, $PM_{2.5}$ mass concentration, and total suspended particle (TSP) collection. The results of the present study have shown significant differences between public transports as commuting modes in Fukuoka. The PM exposure levels on subway platform and inside subway train were overwhelmingly higher than those of other points on commuting route. The relative ratio between modes (i.e., the ratio of $PM_{2.5}$ inside subway to that inside bus) provides an idea for choosing a right commuting mode for our health. This study clearly provided evidence of the extremely high levels of iron exposure by subway uses compared to bus uses. The result of theoretically reconstructed mass concentration of $PM_{2.0-0.3}$ collected on subway platform suggests that the PM of underground subway will be associated with PM both generated in subway system and inleakaged from outdoor environment.

• Journal of Environmental Science International
• /
• v.13 no.9
• /
• pp.799-806
• /
• 2004

The filtration tests were made in cell with a low concentrated suspension. The suspension with a concentration of $C_{M}$=1.14～2.67$\cdot$$10^{-3}$ g/g consists of paper paint and water. The particles in the suspension have a particle size x<1${\mu}m$. The used depth filters consists of glass fibres, which are coated by polymer. The filtration in depth filters accorded in different mechanism, which were explained by physical models. The model which would be allows to make a promise of the filtration reaction. This filter media allows to get a high filtration time and a good separation rate. The Particle distribution is measured by a photon correlation spectroscopy(PCS). PCS measures particle sizes 0.03 ${\mu}m$${\mu}m$ in the suspension. The filtered suspension has a very low concentration Co{\le}5{\times}10_{-4}$ g/g of solid in sample. The PCS also informs us about the number of the particles in the suspension. The makes it possible to calculate the concentration of the in sample.

• Journal of Environmental Health Sciences
• /
• v.44 no.6
• /
• pp.524-538
• /
• 2018

Objective: This study aimed to identify the size distributions of particulate matter emitted during 3D printing according to operational conditions and estimate particle inhalation exposure doses at each respiratory region. Methods: Four types of printing filaments were selected: acrylonitrile-butadiene-styrene (ABS), polylactic acid (PLA), Laywood, and nylon. A fused deposition modeling (FDM) 3D printer was used for printing. Airborne particles between 10 nm and $10{\mu}m$ were measured before, during, and after printing using real-time monitors under extruder temperatures from 215 to $290^{\circ}C$. Inhalation exposures, including inhaled and deposited doses at the respiratory regions, were estimated using a mathematical model. Results: Nanoparticles dominated among the particles emitted during printing, and more particles were emitted with higher temperatures for all materials. Under all temperature conditions, the Laywood emitted the highest particle concentration, followed by ABS, PLA, and nylon. The particle concentration peaked for the initial 10 to 20 minutes after starting operations and gradually decreased with elapsed time. Nanoparticles accounted for a large proportion of the total inhaled particles in terms of number, and about a half of the inhaled nanoparticles were estimated to be deposited in the alveolar region. In the case of the mass of inhaled and deposited dose, particles between 0.1 and $1.0{\mu}m$ made up a large proportion. Conclusion: The number of consumers using 3D printers is expected to expand, but hazardous emissions such as thermal byproducts from 3D printing are still unclear. Further studies should be conducted and appropriate control strategies considered in order to minimize human exposure.

• Atmosphere
• /
• v.21 no.1
• /
• pp.35-44
• /
• 2011

We investigated characteristics of new particle formation and growth events observed at Gosan climate observatory using Scanning Mobility Particle Sizer (SMPS) measurements of particle number size distribution with 54 size ranges from 10 to 487 nm in October 2009. Four days (17~20 October) and five days (22~26 October) were classified into strong new particle formation and growth event ($N_S$) and weak particle formation and growth event ($N_W$), respectively. $N_S$ and $N_W$ divided by increase of aerosol number concentration in nucleation mode and continuity of growth from nucleation to Aitken mode. Particle growth rates of $N_S$ (5.34~$9.19nm\;h^{-1}$) were greater than that of $N_W$ (2.15~$3.53nm\;h^{-1}$). $N_S$ and $N_W$ were analyzed with synoptic pattern over East Asia, meteorological elements, and sulfur dioxide ($SO_2$) measured at Gosan. We found that $N_S$ was characterized by a fast and northwesterly wind accompanied cold and dry airmass, but $N_W$ was affected airmass originated from South China and come through the Korea Peninsula. The events ($N_S$ and $N_W$) occurred at conditions of high solar flux ($&gt;700W\;m^{-2}$) and low relative humidity (< 60%). The $SO_2$ concentration on $N_S$ and $N_W$ was higher than that on case of non observed new particle formation.

• Nuclear Engineering and Technology
• /
• v.56 no.9
• /
• pp.3483-3490
• /
• 2024

The initial size distribution and morphological parameters of sodium aerosols are critical in evaluating the accidental suspended aerosol behaviour in Sodium-cooled Fast Reactor (SFR) containment. Mass-based measurements were more familiar in characterizing the sodium aerosols. Real-time number size distribution measurements are carried out in this study. The sensitivity analysis of sodium aerosol effective density (ρ_e) in deriving the actual number size distributions from the measured Aerodynamic Particle Size Distributions (APSD) and predicting suspended aerosol dynamics is presented. Tests are conducted in a 1 m³ chamber at 47 ± 3% RH for different initial mass concentrations (M₀) of 0.1, 1, and 2.9 g/m³. The initial APSDs measured just after the generation completions are observed to be polydisperse with the count median aerodynamic diameter (CMAD) < 1 ㎛. The literature reported ρ_e values of sodium aerosols, 2.27, 1.362, and 0.61 g/cm³ are used to derive mobility equivalent PSDs from APSD in each test. The real-time number concentration decay and size growth for four different PSDs are measured and compared with the estimate using nodal method-based code to ascertain the actual parameters. The validated parameters CMD = 0.66 ㎛, σ_g = 1.96, ρ_e = 1 g/cm³ and χ = 1 are used for improved estimation of sodium aerosol dynamics in Indian SFR containment with M₀ = 4 g/m³ for severe accident scenarios.