• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.715-720
• /
• 2002

Silicon nitride samples with aligned whisker seeds were prepared with different amounts of yttria and alumina as the sintering additives. Their sintering behaviors and the microstructural developments between 2123K and 2323K were examined. The sample with larger amount of the sintering additives showed faster densification and grain growth. Even though addition of the aligned whisker seeds slightly retarded densification of silicon nitride, it improved the flexural strength and the fracture toughness. Both the flexural strength and the fracture toughness of silicon nitride with the aligned whisker seeds were increased as the amount of the sintering additives was increased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.321-324
• /
• 2003

The effects of various sintering additives such as $Bi_2O_3+V_2O_5$, $BiVO_4$, $B_2O_3$, and $CuO+V_2O_5$ on the low-temperature sintering and microwave dielectric properties of $(ZnMg)TiO_3$ system were studied. Sintering was enhanced by the sintering additives and highly dense samples were obtained for $(Zn_{0.8}Mg_{0.2})TiO_3$ at the sintering temperature of $910^{\circ}C$. $(Zn_{0.8}Mg_{0.2})TiO_3$ with 6.19 mol.%$B_2O_3$ was found to show the best sintering and microwave dielectric properties.

• 한국분말재료학회지
• /
• 제18권6호
• /
• pp.562-567
• /
• 2011

This paper reports the effect of sintering processes and additives on the microstructures and mechanical properties of $ZrB_2$-SiC composite ceramics. We fabricated sintered bodies of $ZrB_2$-20 vol.% SiC with or without sintering additive, such as C or $B_4C$, densified by spark plasma sintering as well as hot pressing. While almost full densification was achieved regardless of sintering processes or sintering additives, significant grain growth was observed in the case of spark plasma sintering, especially with $B_4C$. With sintered bodies, mechanical properties, such as flexural strength and Vickers hardness, were also examined.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.604-609
• /
• 2011

Additives for low temperature sintering of mullite ceramics were investigated for matching Mo-Cu conducting paste with that ceramics at 1,400$^{\circ}C$. $SiO_2$, MgO and $Y_2O_3$ were chosen as the additives for low temperature sintering, and the amounts of those additives were varied with sintering temperature of 1,400$^{\circ}C$ to 1,500$^{\circ}C$. With additives of 1.0 wt% of $SiO_2$, 1.0 wt% of MgO, and 1.5 wt% of $Y_2O_3$, the densest sintered body of 3.12 g/$cm^3$ was obtained at 1,400$^{\circ}C$ in reducing atmosphere. The flexural strength of that was 325 MPa and the CTE (Coefficient of thermal expansion) was 4.33 ppm/$^{\circ}C$.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.162-165
• /
• 2006

In this study, Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method with $\beta$-SiC powder whose a particle size is 30nm and less on the average in argon condition at 1780 and $1800^{\circ}C$ under 20MPa. Alumina ($Al_2O_3$), yttria ($Y_2O_3$) and silica ($SiO_2$) were used for sintering additives. To investigate effects of particle-size and temperature on $SiO_2$, LPS-SiC was fixed $Al_2O_3$, $Y_2O_3$ and then particle-size of $SiO_2$ were changed as two kinds. The system of particle-size and temperature on sintering additives which affects a property of sintering os well os the influence depending on particle-size and temperature of sintering additives were investigated by measurement of sintering properties. Such as measurement of sintering density, vikers hardness and observing of microstructure were investigated to make sure of the optimum condition which is about matrix of $SiC_f/SiC$ composites. Base on the composition of sintering additives, microstructure and sintering property correlation, the effect of particle-size of sintering additives are discussed. An experimental method to investigate the dynamic characteristics of bums in extreme environmental condition is established.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.266-270
• /
• 2004

SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine because it has excellent high temperature strength, low coefficient of thermal expansion, good resistance to oxidation and good thermal and chemical stability etc. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, SiC/SiC composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing jiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of SiC/SiC composites by hot pressing method. In the present work, monolithic Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method in Ar atmosphere at $1800^{\circ}C$ under 20MPa using $Al_2O_3,\;Y_2O_3\;and\;SiO_2$ as sintering additives in order to low sintering temperature and sintering pressure. The starting powder was high purity $\beta-SiC$ nano-powder with all average particle size of 30mm. The characterization of LPS-SiC was investigated by means of SEM and three point bending test. Base on the composition of sintering additives-, microstructure- and mechanical property correlation, tire compositions of sintering additives are discussed.

• 한국세라믹학회지
• /
• 제15권1호
• /
• pp.3-8
• /
• 1978

Effects on the sintering of zircon by minor additives such as $Al_2O_3$, MgO and CaO were studied at $1450^{\circ}C$~$1550^{\circ}C$ for 30 minutes. Shrinkage, compressive strength, bulk density and apparent porosity of sintered specimens were measured in relation to content of minor additives and temperature. Mineral constitutions of the sintered specimens were idenified with X-ray diffractometer. And microstructures of the sintered specimens were observed by scanning electron microscope. The results obtained were as follow. 1) Effect ofthe minor additives such as Al2O3, MgO and CaO on the sintering of zircon was related to reaction between added oxide and silica by dissociation of zircon. 2) Zircon did not dissociate at $1550^{\circ}C$, but it did slightly on the specimen added by Al2O3 5 wt% at $1550^{\circ}C$. 3) Sintering of zircon was promoted by the addition of MgO, $(Al_2O_3＋CaO)$ and (MgO＋CaO), then, this phenomenon was due to the formation of liquid phase.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.142-147
• /
• 1999

The interaction between commercial $Si_3N_4$ powder and two types of additives (nitrate and oxide additives) during the sintering of $Si_3N_4$ was investigated. The nitrates solution or oxide particles were added as a sintering additives. The surface of mixed powder was observed with FT-IR, TG, and HREM. DTA was used to characterize the reactivity of the powders. The formation of crystalline phases and phase transformation were analyzed by XRD. The adsorption of the additives on the surface of silicon nitride was confirmed in the nitrate salts. It was shown that the adsorption occurred by interaction between the amorphous $SiO_2$ layer on the $Si_3N_4$ surface and metal cations $(Al^{3++\; and \;Y^{3+})$ and anions $(NO_3\;^-\; or\; OH^-)$, resulting in a higher degree of homogeneous distribution of additives.

• 한국세라믹학회지
• /
• 제37권1호
• /
• pp.21-25
• /
• 2000

Gas pressure sintered silicon nitride based composites with 5 wt% $\beta$-Si3N4 whiskers were prepared, and the variations depending on sintering additives and sintering temperature were studied. Sintering additives were 6 wt% Y2O3-1 wt% MgO(6Y1M), 6 wt%Y2O3-1 wt% Al2O3(6Y1A), 6 wt% Y2O3-1 wt% SiO2(6Y1S), and whiskers were unidirectionally oriented by a modified tape casting technique. Samples were fully densified by gas pressure sintering at 2148 K and 2273 K. As the sintering temperature increased, the size of large elongated grains was increased. Three point flexural strength of 6Y1M and 6Y1M samples was higher than that of 6Y1S sample, and the strength decreased as the sintering temperature increased. The indentation crack length became shorter for the sample sintered at higher temperature, and the difference between the cracks length parallel to and normal to the direction of whisker alignment was decreased. In case of cracks 45$^{\circ}$off the whisker alignment direction, the crack length anisotropy disappeared.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.467-471
• /
• 2009

Effects of boron and carbon on the densification and thermal decomposition of an AlN-SiC-$TiB_2$ system were investigated. $SiO_2$ was mostly removed by the addition of carbon, while $Al_2O_3$ formed $Al_4O_4C$ and promoted the densification of the systems above $1850^{\circ}C$. Rather porous specimens were obtained without the additives after hot pressing at $2100^{\circ}C$, while densification was mostly completed at $2000^{\circ}C$ by using the additives. The sintering temperature decreased further to $1950^{\circ}C$ by applying spark plasma sintering. The additives promoted the shrinkage of AlN by forming a liquid phase which was originated from the carbo- and boro-thermal reduction of $Al_2O_3$ and AlN.