• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.782-786
• /
• 2010

Thrust deduction related to the prediction of power performance of a ship is rather resistance increase, and as a preliminary study for it forces upon a circular cylinder in a uniform flow of ideal fluid due to singularities located behind it are investigated. The circle theorem is used to get the complex velocity potential for the flow field under consideration, and the Blasius theorem is applied to obtain forces upon the circular cylinder. As singularities sinks, point vortices and dipoles and their combinations are treated. $\varepsilon$, standing for the strength of a singularity, and $\delta$, representing the distance between the cylinder and the singularity, are important small parameters for the resistance and lateral forces. For sinks or point vortices it is shown that the dimensionless forces upon the cylinder is O($\epsilon$) if $\epsilon$= O($\delta$) is assumed, and the same holds for dipoles if $\epsilon$= O(${\delta}^3$) is supposed. Forces upon the cylinder by a symmetric pair of sinks are greater than a single sink located at the central plane since there is an additional term due to cross effects, and the same is also valid for the case of dipole. Combination of dipole and a point vortex is also considered and a few new aspects are clarified.

• Korean Journal of Metals and Materials
• /
• v.50 no.12
• /
• pp.873-882
• /
• 2012

Dual Phase (DP) steel which has a soft ferrite phase and a hard martensite phase reveals both high strength and high ductility and has received increased attention for use in automotive applications. To conduct structural analysis to verify vehicle safety, highly credible experimental results are required. In this study, tensile tests were performed in a strain rate range from $10^{-4}/s$ to 300/s for Sink Roll-Less (SRL) hot-dip metal coated sheets. Collision properties were estimated through simulation by LS-DYNA using the stress-strain curve obtained from the tensile test. The simulation results were compared with the actual crash test results to confirm the credibility of the simulation. In addition, a tensile test and a crash test with 2% prestrain and a baking (PB) specimen were evaluated identically because automotive steel is used after forming and painting. The mechanical behaviors were improved with an increasing strain rate regardless of the PB treatment. Thus, plastic deformation with an appropriate strain rate is expected to result in better formability and crash characteristics than plastic deformation with a static strain rate. The ultimate tensile strength (UTS) and absorbed energy up to 10% strain were improved even though the total elongation decreased after PB treatment, The results of the experimental crash test and computer simulation were slightly different but generally, a similar propensity was seen.

• Journal of Plant Biology
• /
• v.36 no.4
• /
• pp.363-370
• /
• 1993

Experiments with non-nodulated alfalfa (Medicago sativa L. cv, Europe) plants grown in hydroponic cuiture, were carried out to estimate the remobiJization of nitrogen (N) reserves and to investigate the transported forms of reduced soluble-N in xylem during regrowth following shoot removal. Endogenous N remobilization were estimated by $^{15}N$ labelling and amino acids in xylem sap were analysed. The, $^{15}N$ contents of ~egr9wing leaves and stems increased as a result of remobilization of N reserves mainly from root ,system, Regrowing leaves were a stronger sink than regrowing stems, with about tWo-thirds of remobilized 15N being recoved in leaves. Endogenous N in lateral roots accounted for about 46% of the total N reserves used for regrowth, while tap roots accounted for 23%, About 72% of total endogenous N remobilized to regrowing shoot, occurred during the first 10 days of regrowth, The outflow of reduced soluble-N (mainly amino acids) was greater than that of protein-N, while the latter was the largest storage pool in tap root and lateral roots. It is suggested that amino acids-N was the most readily avaiable form of N reserves. Asparagine, which repre5ented about 75% of amino acids-N in xylem sap, was the main transported form of reduced N. Its relative contents, during the first 10 days of regrowth, decreased from 75% to 59%. This decline was accompanied by compensatory increase in the relative contents of asparatate and glutamine.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.2
• /
• pp.35-48
• /
• 1985

The present work develops a method of evaluating thrust deduction and wake for different loads of the propeller using the concerted application of the theoretical tools and experimental techniques. It also shows the applicability of the new method to the design of optimum hull form. Firstly, the problem of hull-propeller interaction was analyzed in terms of inviscid as well as viscous components of the thrust deduction and wake. The wavemaking resistance of a hull and propeller were mathematically represented by sources on the hull surface and sink on the propeller plane, respectively. The strength of sink was determined by utilizing the radial distributions of propeller load and nominal wake. The resistance increment due to a propeller and the axial perturbation flow induced by the hull in the propeller plane were calculated. Especially, the inviscid component of the thrust deduction was calculated by subtraction the wavemaking resistance of a bare hull, the wavemaking resistance of a free-running propeller and the augmentation of propeller resistance due to hull action from the wavemaking resistance of the hull with a propeller. The viscous components of the thrust deduction and wake were estimated as functions of propeller load which were established by the propeller load varying test after deduction the calculated inviscid components. Secondly, an analysis method of powering performance was developed based on the potential theory and the propeller load varying test. The hybrid method estimates the thrust deduction, wake and propeller open-water efficiency for different propeller load. This method can be utilized in the analysis of powering performance for the propeller load variation such as the added resistance due to hull surface roughness, the added resistance due to wind, etc. Finally, the hybrid method was applied to the optimum design of hull form. A series of afterbody shapes was obtained by systematically varying the waterplane and section shapes of a parent afterbody without changing the principal dimensions, block coefficient and prismatic coefficient. From the comparison of the predicted results such as wavemaking resistance, thrust deduction, wake and delivered power, an optimum hull form was obtained. The delivered power of the optimized hull form was reduced by 5.7% which was confirmed by model tests. Also the predicted delivered power by the hybrid method shows fairly good agreement with the test result. It is therefore considered that the new analysis method of powering performance can be utilized as a practical tool for the design of optimum hull form as for the analysis of powering performance for the propeller load variation in the preliminary design stage.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.813-822
• /
• 2002

The purpose of the present study is first to refine the mathematical material models for moisture and temperature distributions in early-age concrete and then to incorporate those models into finite element procedure. The three dimensional finite element program developed in the present study can determine the degree of hydration, temperature and moisture distribution in hardening concrete. It is assumed that temperature and humidity fields are fully uncoupled and only the degree of hydration is coupled with two state variables. Mathematical formulation of degree of hydration Is based on the combination of three rate functions of reaction. The effect of moisture condition as well as temperature on the rate of reaction is considered in the degree of hydration model. In moisture transfer, diffusion coefficient is strongly dependent on the moisture content in pore system. Many existing models describe this phenomenon according to the composition of mixture, especially water to cement ratio, but do not consider the age dependency. Microstructure is changing with the hydration and thus transport coefficients at early ages are significantly higher because the pore structure in the cement matrix is more open. The moisture capacity and sink are derived from age-dependent desorption isotherm. Prediction of a moisture sink due to the hydration process, i.e. self-desiccation, is related to autogenous shrinkage, which may cause early-age cracking in high strength and high performance concrete. The realistic models and finite element program developed in this study provide fairly good results on the temperature and moisture distribution for early-age concrete and correlate very well with actual test data.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.3
• /
• pp.173-182
• /
• 2011

The purpose of this paper is to provide useful information for fishermen in the manner of investigation a sinking speed of current type tuna longline gear at the North Pacific Ocean as a new developed tuna longline fishing ground. The sinking depth of mainline in connection with different basket was investigated. The experiments were also performed with different materials such as Supermansen (i.e., PE) and Hitech (i.e., PA) for the mainline to investigate the sinking depth of mainline and hooks. Furthermore, the relation between the sinking depth of hooks and catches are investigated also. The sinking depth of mainline at the first and the last shooting basket shows deeper than that of middle part of a basket due to reduced shortening ratio. The sinking depth of mainline and hook with Hitech material shows more shallow than that of Supermanse material, even the Hitech case was designed to sink deeper than that of Supermanse case. The highest catches arise at the middle part basket as the hook number 7 with around 248m sinking depth. From the results, longline with Hitech material is needed to increase the sinking force for reaching the relevant sinking depth. Moreover, the current strength at the North Pacific Ocean will be considered for further commercial fishing.

• The KIPS Transactions:PartC
• /
• v.17C no.5
• /
• pp.433-440
• /
• 2010

Energy efficiency, low latency and scalability for wireless sensor networks are important requirements, especially, the wireless sensor network consist of a large number of sensor nodes should be minimized energy consumption of each node to extend network lifetime with limited battery power. An efficient algorithm and energy management technology for minimizing the energy consumption at each sensor node is also required to improve transfer rate. Thus, this paper propose no-overlap multi-pass protocol provides for sensor data transmission in the wireless sensor network environment. The proposed scheme should minimize network overhead through reduced a sensor data translation use to searched multi-path and added the multi-path in routing table. Proposed routing protocol may minimize the energy consumption at each node, thus prolong the lifetime of the sensor network regardless of where the sink node is located outside or inside the received signal strength range. To verify propriety proposed scheme constructs sensor networks adapt to current model using the real data and evaluate consumption of total energy.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.321-326
• /
• 2006

Electronic packaging involves interconnecting, powering, protecting, and cooling of semiconductor circuits fur the use in a variety of microelectronic applications. For microelectronic circuits, the main type of failure is thermal fatigue, owing to the different thermal expansion coefficients of semiconductor chips and packaging materials. Therefore, the search for matched coefficients of thermal expansion (CTE) of packaging materials in combination with a high thermal conductivity is the main task for developments of heat sink materials electronics, and good mechanical properties are also required. The aim of this work is to develop copper matrix composites reinforced with carbon nanofibers. The advantages of carbon nanofibers, especially the good thermal conductivity, are utlized to obtain a composite material having a thermal conductivity higher than 400 W/mK. The main challenge is to obtain a homogeneous dispersion of carbon nanofibers in copper. In this paper, a technology for obtaining a homogeneous mixture of copper and nanofibers will be presented and the microstructure and properties of consolidated samples will be discussed. In order to improve the bonding strength between copper and nanofibers, different alloying elements were added. The microstructure and the properties will be presented and the influence of interface modification will be discussed.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.5 no.2
• /
• pp.77-85
• /
• 2000

Simulation of local external forcing and its response in the rotation table experiment has been investigated. Spatially-uniform external forcings have been applied in many experimental studies, however, based on the fact that the north-south distribution of the wind-stress curl and the existence of local maximum of the sea surface heat loss in the northern part of the East Sea, new method of combined effects of local forcings has been employed in separate experiments. Carefully designed local source or sink at the bottom of the cylindrical container can produce horizontal pressure gradient within the Ekman layer, and consequently the interior also attains the same pressure gradient that produces geostrophic interior circulation. In order to keep free surface during the local-surface cooling, a side-wall cooling method is suggested. For the various type of local forcing including the effects local cooling and the periodic change of local wind-stress curl, western-boundary flow in terms of its strength, position of separation from the boundary have been observed.

• Nuclear Engineering and Technology
• /
• v.50 no.1
• /
• pp.132-139
• /
• 2018

Nanocrystalline reduced activation ferritic/martensitic (RAFM) steel samples were prepared using surface mechanical attrition treatment (SMAT). Un-SMATed and SMATed reduced activation ferritic/martensitic samples were irradiated by helium ions at $200^{\circ}C$ and $350^{\circ}C$ with 2 dpa and 8 dpa, respectively, to investigate the effects of grain boundaries (GBs) and temperature on the formation of He bubbles during irradiation. Experimental results show that He bubbles are preferentially trapped at GBs in all the irradiated samples. Bubble denuded zones are clearly observed near the GBs at $350^{\circ}C$, whereas the bubble denuded zones are not obvious in the samples irradiated at $200^{\circ}C$. The average bubble size increases and the bubble density decreases with an increasing irradiation temperature from $200^{\circ}C$ to $350^{\circ}C$. Both the average size and density of the bubbles increase with an increasing irradiation dose from 2 dpa to 8 dpa. Bubbles with smaller size and lower density were observed in the SMATed samples but not in the un-SMATed samples irradiated in the same conditions, which indicate that GBs play an important role during irradiation, and sink strength increases as grain size decreases.