• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권4호
• /
• pp.258-262
• /
• 2004

Storage over Ethernet (SoE) is a network storage architecture that allows direct attachment of existing ATA/ATAPI devices to Ethernet without a separate server. Unlike SAN, no server computer intervenes between the storage and the client hosts. We propose a SoE disk controller (SoEDC) amenable to low-cost, single-chip implementation that processes a simplified L3/L4 protocol and converts commands between Ethernet and ATA/ATAPI, while the rest of the complex tasks are performed by the remote hosts. Thanks to simple architecture and protocol, the SoEDC implemented on a single $4mm{\times}4mm$ chip in 0.18um CMOS technology achieves maximum throughput of 55MB/s on Gigabit Ethernet, which is comparable to that of a high-performance disk storage locally attached to a host computer.

• 제어로봇시스템학회논문지
• /
• 제22권8호
• /
• pp.671-677
• /
• 2016

A Controller Area Network (CAN) is a serial communication protocol that is highly reliable and efficient in many aspects, such as wiring cost and space, system flexibility, and network maintenance. Therefore, it is chosen for the communication protocol between a single chip controller based on Field Programmable Gate Array (FPGA) and peripheral devices. In this paper, the design and implementation of CAN IP, which is written in VHSIC Hardware Description Language (VHDL), is presented. The implemented CAN IP is based on the CAN 2.0A specification. The CAN IP consists of three processes: clock generator, bit timing, and bit streaming. The clock generator process generates a time quantum clock. The bit timing process does synchronization, receives bits from the Rx port, and transmits bits to the Tx port. The bit streaming process generates a bit stream, which is made from a message received from a micro controller subsystem, receives a bit stream from the bit timing process, and handles errors depending on the state of the CAN node and CAN message fields. The implemented CAN IP is synthesized and downloaded into SmartFusion FPGA. Simulations using ModelSim and chip test results show that the implemented CAN IP conforms to the CAN 2.0A specification.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 추계학술대회 논문집 학회본부
• /
• pp.250-253
• /
• 1989

As the necessity of increasing the midnight base load is extensively increased, electric power companies have to increase the demand of midnight electrical power by lowering the electrical charge rate at midnight. One of the most widely used midnight equipments is the heat Storage type's electrical boiler. A Single chip microprocessor controller for the heat-storage type's electrical boiler is developed. This controller call reduce the undesirable peak load at the begining of midnight (i.e.11 P.M.) time band by using backward load control method. Futhermore, this controller enables reservation of heat storge and the effective heating control the field test has been done by use the boiler for 66$m^2$ with the heater of 21KW quality.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.869-872
• /
• 2005

In this paper we present a switch wrapper for an AMBA AXI, which is an efficient on-chip-network interface compared to bus-based interfaces in a multiprocessor SoC. The AXI uses an idea of NoC to provide the increasing demands on communication bandwidth within a single chip. A switch wrapper for AXI is located between a interconnection network and two IPs connecting them together. It carries out a mode of routing to interconnection network and executes protocol conversions to provide compatibility in IP reuse. A switch wrapper consists of a direct router, AHB-AXI converters, interface modules and a controller modules. We propose the design of a all-in-one type switch wrapper.

• 전자공학회논문지B
• /
• 제31B권10호
• /
• pp.21-31
• /
• 1994

This paper describes the multichannel combined R2MFC/DTMF/CCT reciver which provides a signaling service functions for call processing control in digital switching system. Using the TMS320C25 DSP chip, we have implemented multi-function receriver shich processes 8 channels of R2MFC, DTMF, and CCT signals simultaneously. In order to increase the channel multiplicity of the combined receiver. R2MFC and CCT receiver were employed by discrete Fourier transform(DFT) method using Goertzel algorithm, and DTMFreceiver was employ by infinite impulse reponse(IIR) filtering method using 4KHz subsampling technique. The combined receiver has 4 function modes for each channel such as R2MFC, DTMF, CCT, and Idle modes. The function mode of each channel may be selected at any time by single-chip micro-controller(.mu.C). Hence, the number of channels assigned for each function mode can be adjusted dynamically according to the signaling traffic variations. From the experimental test results using the test-bed, it has been proved that the combined receiver statisfies all receiver satisfies all receiver specifications, and provides good channel multiplicity and performance, Therefore, it may give a great improvement than existing receiver in cost, reliability, availability, and serviceability.

• 소음진동
• /
• 제11권1호
• /
• pp.147-155
• /
• 2001

This paper is concerned with the real-time automatic tuning of the multi-input multi-output positive position feedback controllers for smart structures by the genetic algorithms. The genetic algorithms have proven its effectiveness in searching optimal design parameters without falling into local minimums thus rendering globally optimal solutions. The previous real-time algorithm that tunes a single control parameter is extended to tune more parameters of the MIMO PPF controller. We employ the MIMO PPF controller since it can enhance the damping value of a target mode without affecting other modes if tuned properly. Hence, the traditional positive position feedback controller can be used in adaptive fashion in real time. The final form of the MIMO PPF controller results in the centralized control, thus it involves many parameters. The bounds of the control Parameters are estimated from the theoretical model to guarantee the stability. As in the previous research, the digital MIMO PPF control law is downloaded to the DSP chip and a main program, which runs genetic algorithms in real time, updates the parameters of the controller in real time. The experimental frequency response results show that the MIMO PPF controller tuned by GA gives better performance than the theoretically designed PPF. The time response also shows that the GA tuned MIMO PPF controller can suppress vibrations very well.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.401-404
• /
• 1991

In this paper, the controllers for the motion of the 2-joint manipulator design two stages: (1) a primary controller that under ideal conditions makes the end-effector track the desired trajectory: (2) a secondary controller that compensates for undesirable deviations of the motion from the disired trajectory caused by external and/or internal disturbances. The secondary contoller is applied to PID control algorithm. and the controllers is actually designed using IBM-PC/AT and 8096 single chip microprocessor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.1852-1853
• /
• 2006

This paper describes the development of temperature controller using program control method for small heating system. This system consists of three parts; sensing part, control part that includes the PID control algorithm, and actuating part. We introduce a zero-crossing control method of TRIAC and firmware technique using single chip micro-controller(ATmega8535) in the control part.

• 태양에너지
• /
• 제18권1호
• /
• pp.27-34
• /
• 1998

태양광 발전 시스템의 운용에 있어서 부하의 변동, 일사량, 주변온도등에 의한 최대전력점의 추종은 매우 어려운 기술을 요구한다. 본 연구에서는 이러한 최대전력점의 추종에 있어 빠른 수렴 특성을 얻기 위한 알고리즘으로써 신경 제어기법을 이용하여서 기존의 제어 방식에 의한 동특성과 비교하여 적절한 제어기법 및 시스템동작의 우수한 특성을 얻게 되었다. 즉 최대전력점의 추종 및 안정한 전원의 공급을 갖게되었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.222-224
• /
• 2006

To improve the drawback of LCMPPT(Limit Cycle Maximum Power Point Tracking) controller of the existing two power conversion stages, an advanced MPPT scheme of single power conversion stage is proposed in this paper. This topology is faster on the control speed by means of current control method and the system configuration is simpler. The Authors produce a battery charger by using a cost effective one-chip processor (PIC16F877A) and evaluate another application on the basis of simulation. As a result, the proposed new LCMPPT algorithm is confirmed to be stable and useful.