• Nuclear Engineering and Technology
• /
• 제31권5호
• /
• pp.486-497
• /
• 1999

The local heat transfer coefficient is experimentally investigated for the reflux condensation in a countercurrent flow between the steam-air mixture and the condensate, A single vertical tube has a geometry which is a length of 2.4m, inner diameter of 16.56mm and outer diameter of 19.05mm and is made of stainless steel. Air is used as a noncondensible gas. The secondary side has a shape of annulus around vertical tube and the lost heat by primary condensation is transferred to the coolant water. The local temperatures are measured at 11 locations in the vertical direction and each location has 3 measurement points in the radial direction, which are installed at the tube center, at the outer wall and at the coolant side. In three different pressures, the 27 sets of data are obtained in the range of inlet steam flow rate 1.348∼3.282kg/hr, of inlet air mass fraction 11.8∼55.0%. The investigation of the flooding is preceded to find the upper limit of the reflux condensation. Onset of flooding is lower than that of Wallis' correlation. The local heat transfer coefficient increases as the increase of inlet steam flow rate and decreases as the increase of inlet air mass fraction. As an increase of the system pressure, the active condensing region is contracted and the heat transfer capability in this region is magnified. The empirical correlation is developed by 165 data of the local heat transfer. As a result, the Jacob number and film Reynolds number are dominant parameters to govern the local heat transfer coefficient. The rms error is 17.7% between the results by the experiment and by the correlation.

• Journal of Chest Surgery
• /
• 제22권3호
• /
• pp.416-424
• /
• 1989

We have performed eight, single transplantations of right lung in dogs from September, 1988 to March 1989 at the Thoracic & Cardiovascular Surgical department, Yonsei University, College of Medicine, Seoul, Korea. We wrapped bronchial anastomosis site with great omentum and used cyclosporin in preoperative and postoperative periods in seven cases except one. The one without wrapping the bronchial anastomotic site with omentum and using cyclosporin died due to bronchial anastomotic site rupture in postoperative fourth day. If there is no reason to choose one side over the other, we would generally choose to do left-sided transplant as this is technically somewhat easier because of the long length of recipient bronchus and the ease of clamping the left atrium proximal to the pulmonary veins. The right atrium limits the amount of left atrium that can have incorporated into the clamp proximal to the pulmonary veins on the right side. But we had chosen to do right-sided transplant of lung because we must take variable technical experiences on right sided lung transplant in dogs. We have to anastomose one of pulmonary vein and left atrial wall on right-sided transplant easily only with double ligation of one pulmonary vein because right atrium limited the clamp of left atrium proximal to pulmonary veins with decreased venous return and cardiac output in some dogs. All seven dogs with right-sided lung transplant had survived more than one day with good condition except one. The one dog have to be sacrificed to evaluate the difference between the gas analysis in pulmonary venous and arterial blood in post-operative eight hours. We found hemorrhagic pulmonary edematous changes of contralateral left lung in this dog. And also all dogs have to be sacrificed for the evaluation of surgical problems, anytime in post-operative periods without any cardiopulmonary resuscitative efforts when the general condition would be worse progressively. We found no any surgical technical errors in seven dogs except one with thrombi in suture site of left atrium. There were hemorrhagic pulmonary edematous changes of transplanted right lung in one, of contralateral left lung in one, of contralateral left lung with double ligation of its pulmonary artery in one, thrombi around left atrial sutures sites in one, multiple air leakage in one bronchial rupture in one due to rejection or infection. There were accidental extubation and delayed intubation in one and unknown cause of death in one.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권5호
• /
• pp.396-401
• /
• 1999

In this study, $Ar^+$ ion laser etching process of single/poly-crystalline Si with $CCl_2F_2$ gas is investigated for MEMS applications. In general, laser direct etching process is useful in microelectronic process, fabrication of micro sensors and actuators, rapid prototyping, and complementary processing because of the advantages of 3D micromachining, local etching/deposition process, and maskless process with high resolution. In this study, a pyrolytic method, in which $CCl_2F_2$ gasetches molten Si by the focused laser, was used. In order to analyze the temperature profile of Si by the focused laser, the 3D heat conduction equation was analytically solved. In order to investigate the process parameters dependence of etching characteristics, laser power, $CCl_2F_2$ gas pressure, and scanning speed were varied and the experimental results were observed by SEM. The aspect ratio was measured in multiple scanning and the simple 3D structure was fabricated. In addition, the etching characteristics of $6\mum$ thick poly-crystalline Si on the insulator was investigated to obtain flat bottom and vertical side wall for MEMS applications.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권20호
• /
• pp.9033-9038
• /
• 2014

Background: The purpose of this study was to assess the feasibility of deep inspiration breath-hold (DIBH) based volumetric modulated arc therapy (VMAT) for locally advanced left sided breast cancer patients undergoing radical mastectomy. DIBH immobilizes the tumor bed providing dosimetric benefits over free breathing (FB). Materials and Methods: Ten left sided post mastectomy patients were immobilized in a supine position with both the arms lifted above the head on a hemi-body vaclock. Two thermoplastic masks were prepared for each patient, one for normal free breathing and a second made with breath-hold to maintain reproducibility. DIBH CT scans were performed in the prospective mode of the Varian real time position management (RPM) system. The planning target volume (PTV) included the left chest wall and supraclavicular nodes and PTV prescription dose was 5000cGy in 25 fractions. DIBH-3DCRT planning was performed with the single iso-centre technique using a 6MV photon beam and the field-in-field technique. VMAT plans for FB and DIBH contained two partial arcs ($179^{\circ}-300^{\circ}CCW/CW$). Dose volume histograms of PTV and OAR's were analyzed for DIBH-VMAT, FB-VMAT and DIBH-3DCRT. In DIBH mode daily orthogonal ($0^{\circ}$ and $90^{\circ}$) KV images were taken to determine the setup variability and weekly twice CBCT to verify gating threshold level reproducibility. Results: DIBH-VMAT reduced the lung and heart dose compared to FB-VMAT, while maintaining similar PTV coverage. The mean heart $V_{30Gy}$ was $2.3%{\pm}2.7$, $5.1%{\pm}3.2$ and $3.3%{\pm}7.2$ and for left lung $V_{20Gy}$ was $18.57%{\pm}2.9$, $21.7%{\pm}3.9$ and $23.5%{\pm}5.1$ for DIBH-VMAT, FB-VMAT and DIBH-3DCRT respectively. Conclusions: DIBH-VMAT significantly reduced the heart and lung dose for left side chest wall patients compared to FB-VMAT. PTV conformity index, homogeneity index, ipsilateral lung dose and heart dose were better for DIBH-VMAT compared to DIBH-3DCRT. However, contralateral lung and breast volumes exposed to low doses were increased with DIBH-VMAT.

• 한국결정성장학회지
• /
• 제4권1호
• /
• pp.46-56
• /
• 1994

균일한 자장이 Czochralski도가니에 가하여졌을 때의 유동장, 온도장 및 boron의 농도장이 수치적으로 연구되었다.이러한 Czochralski 도가니에 가하여졌을 때의 유동장, 온도장 및 boron의 농도 장이 수치적으로 연구되어 . 이러한 Caochralski 유동장을 지배하는 인자로는 온도차이에 의한 부력, 자유표면에서의 반경방향으로의 온도 구배로 인한 thermocapillarity, 도가니와 결정의 회전으로 인한 원심력, 외부에서 걸어준 자장에 의한 자성력, boron의 확산계수 및 segregation coefficient 등이 있다. 여기에서 boron의 농도가 매우 낮으므로 농도차이에 의한 부력의 효가 무시되므로 boron의 농도장은 유동장 및 온도장에 영향을 미치지 못한다. 희전방향으로의 대칭성으로 부터 먼저 정상 상태에 대한 자오평면(mericional plane)에서의 속도성분과 회전방향의 속도 성분이 구하여졌으며 온도장도 해석되었다. 이러한 정상상태에서의 유동장 및 온도장으로부터 boron의 농도에 관한 비정상상태에서의 농도구배가 Marangoni convection을 야기하고 있다. 또 비정상 상태의 boron의 농도장의 전달현상은 주로 대류작용에 의존하고 있다.존하고 있다.

• Journal of Chest Surgery
• /
• 제10권2호
• /
• pp.195-204
• /
• 1977

Dynamic lung compliance was measured in healthy ten young[mean age, 26 years] male and five young[mean age, 25 years] female. Lung volume was integrated of the rate of flow signal which was obtained by using pneumotachograph and differential pressure transducer[PM 5, Statham]. Intrapleural pressure was measured as that of intraesophagel pressure. Esophageal ballon, 15. 5cm in length, 4ml of luminal capacity and made of thin latex, was connected to the polyethylene tube that had 12-14 side holes and was of 1.5mm of ID. Transpulmonary pressure was traced by means of differential pressure transducer[PM 131, Statham] to which connected the esophageal balloon catheter and connection tube from mouth piece. Lung volume and transpulmonary pressure were photographed by cathode ray oscilloscope camera while the subjects were breathing spontaneously. Dynamic lung compliance loop was displayed on single trace monitor and subtraction was performed for the quasi-static hysteresis. Dynamic lung compliance was measured, 1. by plotting the pressure-volume relationship 2. from the subtracted pressure-volume loop. Results were as follows. 1. Dynamic lung compliances measured by plotting of healthy young male and female were $0.202{\pm}0.06$ and $0.190{\pm}0.023L/cm$ $H_2O$ respectively. 2. When measured from subtraction loop, dynamic lung compliance for male and female were $0.327{\pm}0.107$, and $0.27{\pm}0.06L/cm$ $H_2O$ respectively. 3. Dynamic chest wall and total respiratory system compliance were also measured. 4. Dynamic lung compliance by plotting appeared to be essentially same when compared to that of static compliance reported previously from our laboratory, however, that obtained from subtraction loop revealed higher values than the compliances obtained by plotting and that of static compliance.

• 한국산학기술학회논문지
• /
• 제14권2호
• /
• pp.554-560
• /
• 2013

본 연구에서는 양쪽 대칭으로 지지할 수 있는 쉴드캔 클립을 제안하며, 그 특징은 장착과 탈착의 하중을 일정하게 하고 납땜 부위의 평판도를 유지 할 수 있도록 개발하였다. 또한 인쇄회로기판에 부착 고정되는 베이스부 및 쉴드캔의 측벽을 집게 형태로 집을 수 있도록 하는 클립부로 구성되며, 클립부 중앙을 절단하여 2군데를 지지 할 수 있게 이루어진다. 또한 넓어진 베이스부와 인쇄회로기판 사이에 납땜이 잘될 수 있도록 오목한 홈을 만들었다. 연구절차는 우선 메커니즘을 설정하고 구조해석 및 진동모드 해석을 수행하여 설계변수를 확정한 후, 제품을 설계하였다. 제조를 위한 전용기를 개발한 후 시제품을 제작하여 성능 평가 후 해석값과 비교 분석하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 추계 학술대회논문집
• /
• pp.93-97
• /
• 2005

Air interlacing serves to protect the yarn against damage, strengthens inter-filament compactness or cohesion, and ensures fabric consistency. The air interlacing nozzle is used to introduce intermittent nips to a filament yarn so as to improve its performance in textile processing. This study investigates the effect of interlacing nozzle geometry on the interlacing process. The geometries of interlacing nozzles with multiple air inlets located across the width of a yarn channels are investigated. The basic interlacing nozzle is the yarn channel, with a perpendicular single air inlet in the middle. The yarn channel shapes are cross sections with semicircular or rectangular shapes. This paper presents three doubled sub air inlets with main air inlet and one of them is slightly inclined doubled sub air inlets with main air inlet. The compressed air coming out from the inlet hits the opposing wall of the yarn channel, divides into two branches, flows trough the top side of yarn channel, joins with the compressed air coming out from the sub air inlet and then creates two free jets at both ends of the yarn channel. The compressed air moves in the shape of two opposing directional vortices. The CFD-FASTRAN was used to perform steady simulations of impinging jet flow inside of the interlace nozzles. The vortical structure and the flow pattern such as pressure contour, particle traces, velocity vector plots inside of interlace nozzle geometry are discussed in this paper.

• 한국농공학회논문집
• /
• 제52권2호
• /
• pp.67-73
• /
• 2010

Unlike Urban building, horticultural facilities has a lot of heat loss through plastic or glass covering material which could be much influential to growing plant and consuming energy for heating greenhouse. In many cases, heat loss from a break of cover, a gap of joint sealing, the entrance to greenhouse and windows for ventilation are the main factors considered in calculating the heating load for horticultural facilities. however the normal observation through human eye and digital camera could not recognize where the heat loss occurred. but the infrared thermal image camera with detecting thermal difference could be very effective for noticing heat loss by analyzing infrared thermal image. In this study, greenhouse structure, covering material, internal and external provisions for Horticultural facilities were surveyed in different sites and Infrared thermal camera shooting and image analysis were performed for auditing heat loss from cultivation facilities The results from this study were that unexpected heat loss had been noticed in 7 representative cases of greenhouse such as side wall covered with single or double plastic, and the joint of horizontal thermal curtain, roof without horizontal thermal curtain, entrance to greenhouse, windows for ventilation. the most important factors for keeping heat energy were whether the horizontal thermal curtain with multifold thermal material was installed or not. The internal or external covering using multifold thermal curtain proved to be the most effective ways to keep heat energy from losing through heat transmission, heat radiation. from inside to outside the horticultural facilities.

• Asian Journal of Atmospheric Environment
• /
• 제12권1호
• /
• pp.47-58
• /
• 2018

The aim of this work is to investigate the effect of atmospheric stability on near-field pollutant dispersion from rooftop emissions of a single cubic building using computational fluid dynamics (CFD). This paper used the shear stress transport (here after SST) k-${\omega}$ model for predicting the flow and pollutant dispersion around an isolated cubic building. CFD simulations were performed with two emission rates and six atmospheric stability conditions. The results of the simulations were compared with the data from wind tunnel experiments and the result of simulations obtained by previous studies in neutral atmospheric condition. The results indicate that the reattachment length on the roof ($X_R$) obtained by computations show good agreement with the experimental results. However, the reattachment length of the rooftop of the building ($X_F$) is greatly overestimated compared to the findings of wind tunnel test. The result also shows that the general distribution of dimensionless concentration given by SST k-${\omega}$ at the side and leeward wall surfaces is similar to that of the experiment. In unstable conditions, the length of the rooftop cavity was decreased. In stable conditions, the horizontal velocity in the lower part around the building was increased and the vertical velocity around the building was decreased. Stratification increased the horizontal cavity length and width near surface and unstable stratification decreased the horizontal cavity length and width near surface. Maintained stability increases the lateral spread of the plume on the leeward surface. The concentration levels close to the ground's surface under stable conditions were higher than under unstable and neutral conditions.