• Korean Journal of Materials Research
• /
• v.18 no.12
• /
• pp.655-659
• /
• 2008

The NO gas sensing properties of ZnO-carbon nanotube (ZnO-CNT) composites fabricated by the coaxial coating of single-walled CNTs with ZnO were investigated using pulsed laser deposition. Upon examination, the morphology and crystallinity of the ZnO-CNT composites showed that CNTs were uniformly coated with polycrystalline ZnO with a grain size as small as 5-10 nm. Gas sensing measurements clearly indicated a remarkable enhancement of the sensitivity of ZnO-CNT composites for NO gas compared to that of ZnO films while maintaining the strong sensing stability of the composites, properties that CNT-based sensing materials do not have. The enhanced gas sensing properties of the ZnO-CNT composites are attributed to an increase in the surface adsorption area of the ZnO layer via the coating by CNTs of a high surface-to-volume ratio structure. These results suggest that the ZnO-CNT composite is a promising template for novel solid-state semiconducting gas sensors.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.6 s.52
• /
• pp.133-135
• /
• 2006

We propose and fabricate a novel fiber optic sensor for the detection of abnormal structural signals from various constructions. It's advantages are highly sensitive. small in dimension and electro-magnetic immune. Since this sensor was simply constructed with a single-mode fiber at infra-red wavelength and a laser-diode with the wavelength of 625 nm, the modes in the end of the optical fiber were not show as Gaussian distributed. So, we used the change of the mode distribution to get the sensor output by the external abnormal effect of structures. We investigated the resonance by performing the bending test of an aluminum beam attached with the fiber sensor. In the test, we could obtained a feasible signal to sense the abnormal condition of structures.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.71-77
• /
• 2015

Ultrasonic imprinting is a micropattern replication technology for a thermoplastic polymer surface that uses ultrasonic vibration energy; it has the advantages of a short cycle time and low energy consumption. Recently, ultrasonic imprinting has been further developed to extend its functionality: (i) selective ultrasonic imprinting using mask films and (ii) repetitive ultrasonic imprinting for composite pattern development. In this study, selective ultrasonic imprinting was combined with repetitive imprinting in order to replicate versatile micropatterns. For this purpose, a repetitive imprinting technology was further extended to utilize mask films, which enabled versatile micropatterns to be replicated using a single mold with micro-prism patterns. The replicated hybrid micropatterns were optically evaluated through laser light images, which showed that versatile optical diffusion characteristics can be obtained from the hybrid micropatterns.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.12
• /
• pp.19-26
• /
• 2005

We have studied the relationship between static mode behavior and dynamic characteristics of multiple transverse-mode VCSELs by measuring the modal L-I and I-V characteristics. Dependence of the resonance frequencies of RIN (relative intensity noise) spectra on the injection current can be understood by modal L-I characteristics and mode-coupling effects. Each transverse mode behaves as an independent diode laser with the different threshold current in large active-area VCSELs, and the multiple-step turn-on is observed when step-current input is applied. This multiple-step turn-on is a result of different turn-on delay times of the transverse modes. Since the multiple-step turn-on increases the rise-time significantly, the wide active-area VCSELs are not suitable for high-speed optical transmitters unless the input current is adjusted for single transverse-mode operation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.6
• /
• pp.231-238
• /
• 2015

Sapphire single crystals have been highlighted for epitaxial of gallium nitride films in high-power laser and light emitting diode industries. Among the many crystal growth methods, vertical Bridgman process is an excellent commercial method for growing high quality sapphire crystals with c-axis. In this study, the thermally induced stress in Sapphire during the vertical Bridgman crystal growth process was investigated using a finite element model. A vertical Bridgman process of 2-inch Sapphire was considered for the model. The effects of vertical and transverse temperature gradients on the thermal stress during the process were discussed based on the finite element analysis results.

• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.607-612
• /
• 2009

We investigated the effects of Co doping on the NO gas sensing characteristics of ZnO-carbon nanotube (ZnO-CNT) layered composites fabricated by coaxial coating of single-walled CNTs with ZnO using pulsed laser deposition. Structural examinations clearly confirmed a distinct nanostructure of the CNTs coated with ZnO nanoparticles of an average diameter as small as 10 nm and showed little influence of doping 1 at.% Co into ZnO on the morphology of the ZnO-CNT composites. It was found from the gas sensing measurements that 1 at.% Co doping into ZnO gave rise to a significant improvement in the response of the ZnO-CNT composite sensor to NO gas exposure. In particular, the Co-doped ZnO-CNT composite sensor shows a highly sensitive and fast response to NO gas at relatively low temperatures and even at low NO concentrations. The observed significant improvement of the NO gas sensing properties is attributed to an increase in the specific surface area and the role as a catalyst of the doped Co elements. These results suggest that Co-doped ZnOCNT composites are suitable for use as practical high-performance NO gas sensors.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.8
• /
• pp.387-391
• /
• 2006

The Ag photodoping effect in amorphous $As_{40}Ge_{10}Se_{15}S_{35}$ chalcogenide thin films for holographic recording has been investigated using a He-Ne laser (${\lambda}$=632.8 nm). The chalcogenide films thickness prepared in the present work were thinner in comparison with the penetration depth of recording light ($d_p=1.66{\mu}m$). It exhibits a tendency of the variation of the diffraction efficiency (${\eta}$) in amorphous chalcogende films, independently of the Ag photodoping. That is, ${\eta}$ increases rapidly at the beginning of the recording process and reaches the maximum (${\eta}_{max}$) and slowly decreases slowly with the exposed time. In addition, the value of ${\eta}_{max}$ depends strongly on chalcogenide film thickness(d) and its maximum peak among the films with d = 40, 80, 150, 300, and 633 nm is observed 0.083% at d = 150 nm (approximately 1/2 ${\Delta}n$), where ${\Delta}$n is the refractive index of chalcogenide thin film (${\Delta}n=2.0$). The ${\eta}$ is largely enhanced by Ag photodoping into the chakogenides. In particular, the value of ${\eta}_{max}$ in a bilayer of 10-nm-thick Ag/150-nm-thick $As_{40}Ge_{10}Se_{15}S_{35}$ film is about 1.6%, which corresponds to ${\sim}20$ times larger than that of the single-layer $As_{40}Ge_{10}Se_{15}S_{35}$ thin film (without Ag). And we obtained the diffraction pattern according to the formation of (P:P) polarization holographic grating using Mask pattern and SLM.

• Carbon letters
• /
• v.19
• /
• pp.72-78
• /
• 2016

Spinnable pitches and carbon fibers were successfully prepared from petroleum or coal pyrolysis residues. After pyrolysis fuel oil (PFO), slurry oil, and coal tar were simply filtered to eliminate the solid impurities, the characteristics of the raw materials were evaluated by elemental analysis, ¹³C nuclear magnetic resonance spectrometer, matrix-assisted laser desorption/ionization time-of-flight mass spectrometer (MALDI-TOF-MS), and so on. Spinnable pitches were prepared for melt-spinning carbon fiber through a simple distillation under strong nitrogen flow, and further vacuum distillation to obtain a high softening point. Carbon fibers were produced from the above pitches by single-hole melt spinning and additional heat treatment, for oxidization and carbonization. Even though spinnable pitches and carbon fibers were processed under the same conditions, the melt-spinning and properties of the carbon fiber were different depending on the raw materials. A fine carbon fiber could not be prepared from slurry oil, and the different diameter carbon fibers were produced from the PFO and coal tar pitch. These results seem to be closely correlated with the initial characteristics of the raw materials, under this simple processing condition.

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.2
• /
• pp.175-178
• /
• 2011

An optical fiber-based beam width measurement technique is presented. The proposed system can be applied to the optical fiber industry in applications such as lensed fiber, optical fiber based laser beam source, and fiber optic sensor. The measurement system is composed of optical fiber, which is used as a transceiver, and a single grating panel which consists of a multi-reflection area with an even non-reflection area. The grating panel is used to vary the reflected light. When the widths of the reflection area and non-reflection area are larger than the optical beam width, the reflected light is varied at the interface between the reflection area and the non-reflection area by the movement of the grating panel. Experiments were conducted in order to verify the feasibility of the proposed technique. Multi-mode fiber combined with a collimator was selected as an emitter and a receiver, and the beam width measurement system was contrived. Subsequently, the proposed method and the system were verified by comparing the experimental results with the results of the conventional charge-coupled device technique.

• Archives of Plastic Surgery
• /
• v.45 no.5
• /
• pp.403-410
• /
• 2018

Background Radiation-induced skin injury is a dose-limiting complication of radiotherapy. To investigate this problem and to develop a framework for making decisions on treatment and dose prescription, a murine model of radiation-induced skin injury was developed. Methods The dorsal skin of the mice was isolated, and irradiation was applied at single doses of 15, 30, and 50 Gy. The mice were followed for 12 weeks with serial photography and laser Doppler analysis. Sequential skin biopsy samples were obtained and subjected to a histological analysis, immunostaining against transforming growth factor beta (TGF-${\beta}$), and Western blotting with Wnt-3 and ${\beta}$-catenin. Increases in the levels of TGF-${\beta}$, Wnt, and ${\beta}$-catenin were detected after irradiation. Results All tested radiation doses caused progressive dermal thickening and fibrosis. The cause of this process, however, may not be radiation alone, as the natural course of wound healing may elicit a similar response. The latent appearance of molecular and histological markers that induce fibrosis in the 15 Gy group without causing apparent gross skin injuries indicates that 15 Gy is an appropriate dose for characterizing the effects of chronic irradiation alone. Thus, this model best mimics the patterns of injury that occur in human subjects. Conclusions This animal model can be used to elucidate the gross and molecular changes that occur in radiation-induced skin injury and provides an effective platform for studying this adverse effect without complicating the process of wound healing.