• 한국분말재료학회지
• /
• 제25권5호
• /
• pp.375-378
• /
• 2018

Conductive and dielectric SiC are fabricated using electroless plating of Ni-Fe films on SiC chopped fibers to obtain lightweight and high-strength microwave absorbers. The electroless plating of Ni-Fe films is achieved using a two-step process of surface sensitizing and metal plating. The complex permeability and permittivity are measured for the composite specimens with the metalized SiC chopped fibers dispersed in a silicone rubber matrix. The original non-coated SiC fibers exhibit considerable dielectric losses. The complex permeability spectrum does not change significantly with the Ni-Fe coating. Moreover, dielectric constant is sensitively increased with Ni-Fe coating, owing to the increase of the space charge polarization. The improvements in absorption capability (lower reflection loss and small matching thickness) are evident with Ni-Fe coating on SiC fibers. For the composite SiC fibers coated with Ni-Fe thin films, a -35 dB reflection loss is predicted at 7.6 GHz with a matching thickness of 4 mm.

• 접착 및 계면
• /
• 제4권1호
• /
• pp.9-17
• /
• 2003

오늘날 산업에서는 환경오염의 줄이고 에너지 절약에 기여할 수 있다는 이유에서 용매를 사용하지 않는 UV 하드코팅재료의 개발이 점차로 많은 주의를 끌고 있다. 본 연구는 실질적으로 산업에 이용될 수 있는 실리콘아크릴레이트(SAOC)를 포함하고 있는 UV 경화코팅제를 개발하고자 수행되었다. 실험의 결과, 수지조성물 중 SAOC의 형태나 농도가 UV 경화필름의 여러 가지 물성에 영향을 주었다. SAOC가 수지조성물에 도입되었을 때 경화된 필름의 물성은 SAOC가 함유되지 않은 도막과 비교하여 개선되었다. 특히, UV 하드 코팅의 내화학성, 내마모성, 내후성과 같은 성질들은 향상되었으며, 코팅된 폴리카보네이트 기재의 충격특성은 코팅되지 않은 PC에 비해 개선되었다. 30 wt% SAOC를 함유하고 있는 경화필름이 가장 좋은 물성을 나타내었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1337-1339
• /
• 2001

We have investigated the relation between the molecular weight distribution (MWD) of diffusible species and the recovery rate of hydrophobicity of room-temperature vulcanizing (RTV) silicone rubber (SIR) using solvent extraction at various temperatures. It was observed that the extract had a MWD ranging from a few hundreds g/mol to hundreds of thousands g/mol. By measuring the migration of siloxane to the extracted SIR surface through a thin carbon coating, the aspect of migration of diffusible species was observed as a real time plot, and the time constant of the migration was also calculated. According to the time dependence of IR-absorbance, the time constant was increased with the increase of MW of the extracts.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.62-71
• /
• 1999

Integrating micro-machined sensors and actuators on the conventional devices with the copper power lines was incompatible to fabricate the mass produced micro electromechanical system (MEMS) devices. To achieve the compatibility of the wiring method between MEMS parts and devices, we developed the three-dimensional sputter-evaporation system that coats micropatterned thin copper films on the surface of the MEMS element. The system consists of a process chamber, two branch chambers, the substrate holder, and a linear-rotary motion feedthrough. Thin copper film was sputtered and evaporated on the biocompatible polymer, Pellethane$^{circed{R}}$ and silicone, catheter that is 2 mm in diameter and 700 mm in length. The metal film coating technique with three-dimensional thin film sputter-evaporation system was developed to apply the power and signal lines on the micro active endoscope. In this paper, we developed the three-dimensional metal film sputter-evaporation system operated on the low temperature for the biopolymeric substrates used in the medical MEMS devices.

• 마이크로전자및패키징학회지
• /
• 제21권3호
• /
• pp.31-35
• /
• 2014

본 연구에서는 $TiO_2$ 나노입자를 LED패키지의 봉지재인 실리콘에 분산시키고, 이에 따른 굴절률, 투과율 및 광효율 변화를 평가하였다. $TiO_2$ 나노입자는 LED 봉지재의 굴절율을 증가시켜 LED 패키지의 광추출 효율을 향상시키기 위해 봉지재에 적용되었다. $TiO_2$는 수열합성법을 통해 합성되었고, 합성된 $TiO_2$ 입자에 긴 체인구조의 vinyl silane을 코팅하여 분산시켰다. 분산 처리를 실시한 후에는 대부분의 $TiO_2$ 나노입자가 10~40 nm 이하로 분산되었으나, 100 nm 이상의 긴 입자도 관찰되었다. 실리콘 봉지재에 $TiO_2$ 나노입자 양이 증가할수록 굴절율은 증가하였으나, 투과율은 감소하였다. $TiO_2$ 나노입자가 포함된 실리콘 봉지재로 LED 패키지를 제조하였고, $TiO_2$ 나노입자가 분산된 LED가 $TiO_2$ 나노입자가 없는 LED패키지에 비해 약 13% 이상 광효율이 향상되었다.

• 폴리머
• /
• 제38권3호
• /
• pp.351-357
• /
• 2014

위장관 종양 조직이 스텐트 내로 성장하는 것을 방지하는 피막형 스텐트가 개발되어 널리 사용되고 있으나 위산에 의한 막의 분해로 인해 스텐트 폐쇄나 파손이 있다. 이에 본 연구에서는 위산 환경하에서 막의 성분과 재질 농도에 따른 피막형 스텐트의 물성 변화와 안정성을 살펴보고자 하였다. 스텐트 막의 재질은 실리콘과 폴리우레탄을 사용하였고, 각각의 농도를 15%, 18%, 20%로 하여 제작된 스텐트를 pH 1.2 산성 용액에서 18주 동안 3주 간격으로 변화를 관찰하였다. 피막을 분석한 결과 동일 농도에서 비교하였을 때 실리콘이 폴리우레탄보다 두껍고 균일하게 코팅되었다. 인공 위액에 의한 폴리우레탄 피막의 분해가 실리콘 피막에 비해 심하였다. 반경 방향 팽창력의 크기는 실리콘 피막이 폴리우레탄 피막에 비해 상대적으로 컸다. 반경 방향 팽창력과 변형 회복력 모두 인공 위액에서의 침잠 기간이 경과함에 따라 점차 감소하였고, 폴리우레탄 피막 스텐트에서 감소율이 더 컸다. 결론적으로 실리콘 피막이 폴리우레탄에 비해 위산에 대해 안정성이 높음을 알 수 있었다.

• 대한조선학회논문집
• /
• 제45권1호
• /
• pp.73-80
• /
• 2008

An improved method to measure the dynamic viscoelastic properties of elastomers is proposed. The method is based on the analysis of forced oscillation of a cylindrical sample loaded with inertial mass. No special equipment or instrumentation other than the ordinary vibration measurement apparatus is required. Typical measurement of the viscoelastic properties of a silicone rubber $Silastic^{(R)}$ S2 were measured over the wide frequency range from 10 Hz to 3 kHz under the action of wide region of deformation from $10^{-4}%$ to 5%. It was shown that modulus of elasticity and loss tangent fall on the single curves when the ratio of load mass to sample mass changed from 1 to 20.

• 폴리머
• /
• 제30권3호
• /
• pp.247-252
• /
• 2006

환자가 요도용 카테타를 장기간 착용할 경우 세균흡착에 의한 감염이 유발되어 심각한 부작용을 경험하게 된다. 본 연구에서는 다양한 양친성 폴리우레탄을 합성하여 요도용 카테타 도포용 소재로서의 응용가능성을 확인하고자 하였다. 양친성 폴리우레탄은 친수성 고분자인 poly(ethylene oxide)(PEO)와 소수성 고분자인 poly (tetramethylene oxide) (PTMO) 또는 poly (dimethyl siloxane) (PDMS)을 연질부로 도입하여 합성하였다. 상용 실리콘 카테타에 양친성 고분자를 도포한 결과 표면의 친수성이 현저히 개선되었다. 특히, PEO의 함량이 많은 폴리우레탄일수록 친수성이 높게 나타났으며, 세균 흡착량이 감소함을 확인할 수 있었다. 결론적으로, 본 연구에서 합성한 양친성 고분자는 요도용 카테타의 도포용 소재로 적합한 것을 알 수 있었다.

• 대한약침학회지
• /
• 제25권4호
• /
• pp.382-389
• /
• 2022

Objectives: The Korean Industrial Standard (KS) for sterile acupuncture needles was established in 2009 based on research on the quality control of acupuncture needles. We aimed to determine the quality of acupuncture needles available in South Korea in 2021 by examining their surface condition and chemical composition using field-emission scanning electron microscopy (FE-SEM) and energy-dispersive X-ray spectroscopy (EDS). Methods: In South Korea, there are 23 brands of acupuncture needles, and we examined 10-15 needles from each brand, resulting in a total of 285 needles. The microstructures of the needles were assessed by SEM. Using SEM images, we evaluated the acupuncture needle tips for the following defects/aspects: scratches, lumps, detached coating, bent tip, and tip sharpness. EDS was used to determine the chemical composition of the selected acupuncture needles. Results: Overall, 88.4% of 285 needles were found to have at least one type of abnormality. The most frequently observed abnormalities were scratches and dents on the surface (68.1%), followed by detached coating (63.2%), and lumps (61.8%); blunt tips were observed in about 24% of them. Of 252 needles with at least one defect, 86.9% had two or more types of defects. The ratio of the number of needles with any defect to that of needles without any defect varied among brands, ranging from 50% to 100%. Regarding foreign materials, higher proportions of Si and O were observed on the needles, indicating incomplete or detached silicone coating. Conclusion: The quality of acupuncture needles varied among brands, suggesting that further improvements can be made through various inspection methods.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1993년도 추계학술발표회논문집
• /
• pp.97-102
• /
• 1993

The application of epxy composite materials for the outdoor insulating systems has some significant advan-tages compared with conventional inorganic materials, that is low weight in combination with high mechanical strength, small dimensions and design versatility. The paper describes the results of high voltage investigations carried out different aging types of epoxy resin insulator and silicone grease coating. The insulators have been exposed 3000 hours to weather-o-meter and 12 months to outdoor. In this connection, the main study of paper is form the basis of develop-ment of principal technologies of epoxy composites which ard: (1)manufacturing of insulator, (2)high vol-tage testing under dry and wet condition, (3)mechani-cal properties, (4)accelerated weather-ometer test and outdoor exposed, artificial polution.