• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.130-135
• /
• 2003

Polycrystalline silicon thin films have been used for low cost thin film device application. However, it was very difficult to fabricate high performance poly-Si at a temperature lower than $600^{\circ}C$ for glass substrate because the crystallization process technologies like conventional solid phase crystallization (SPC) require the number of high temperature (600-$1000^{\circ}C$) process. The objective of this paper is to grow poly-Si on flexible substrate using a rapid thermal crystallization (RTC) of amorphous silicon (a-Si) layer and make the high temperature process possible on molybdenum substrate. For the high temperature poly-Si growth, we deposited the a-Si film on the molybdenum sheet having a thickness of 150 $\mu\textrm{m}$ as flexible and low cost substrate. For crystallization, the heat treatment was performed in a RTA system. The experimental results show the grain size larger than 0.5 $\mu\textrm{m}$ and conductivity of $10^{-5}$ S/cm. The a-Si was crystallized at $1050^{\circ}C$ within 3min and improved crystal volume fraction of 92 % by RTA. We have successfully achieved a field effect mobility over 67 $\textrm{cm}^2$/Vs.

• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.29-34
• /
• 1998

The solid-phase crystallization (SPC) of plasma-enhanced chemical vapor depsoited (PECVD) amorphous silicon (a-Si) films ha s been investigated by x-ray diffraction (XRD). The a-Si films were prepared on Si (100) wafers using $SiH_4$ gas and without $H_2$ dilution at the substrate temperatures between $120^{\circ}C$ and $380^{\circ}C$, and than annealed at $600^{\circ}C$ for crystallization. The annealed samples exhibited (111), (220), and (311) XRD peaks with preferential orientation of (111). The XRD peak intensities increased as the substrate temperature decreased, and the $H_2$dilution suppressed the solid-phase crystallization. The average grain size estimated by XRD analysis for the (111) texture has increased from about 10 nm to about 30 nm, as the substrate temperature decreased. The deposition rate also increased with the decreasing substrate temperature and the grain size was closely dependent on the deposition rate of the films. The grain size enhancement was attributed to an increase of the structural disorder of the Si network.

• Korean Journal of Materials Research
• /
• v.27 no.11
• /
• pp.609-616
• /
• 2017

We investigated a Leidenfrost effect in the growth of ZnO nanostructures on silicon substrates by ultrasonic-assisted spray pyrolysis deposition(SPD). Structural and optical properties of the ZnO nanostructures grown by varying the growth parameters, such as substrate temperature, source concentration, and suction rate of the mist in the chambers, were investigated using field-emission scanning electron microscopy, X-ray diffraction, and photoluminescence spectrum analysis. Structural investigations of the ZnO nanostructures showed abnormal evolution of the morphologies with variation of the substrate temperatures. The shape of the ZnO nanostructures transformed from nanoplate, nanorod, nanopencil, and nanoprism shapes with increasing of the substrate temperature from 250 to $450^{\circ}C$; these shapes were significantly different from those seen for the conventional growth mechanisms in SPD. The observed growth behavior showed that a Leidenfrost effect dominantly affected the growth mechanism of the ZnO nanostructures.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.209-212
• /
• 2011

Hafnium nitride (HfN) thin films were deposited onto a silicon substrate by inductive coupled nitrogen plasma-assisted radio frequency magnetron sputtering. The films were prepared without intentional substrate heating and a substrate negative bias voltage ($-V_b$) was varied from -50 to -150 V to accelerate the effects of nitrogen ions ($N^+$) on the substrate. X-ray diffractometer patterns showed that the structure of the films was strongly affected by the negative substrate bias voltage, and thin film crystallization in the HfN (100) plane was observed under deposition conditions of -100 $V_b$ (bias voltage). Atomic force microscopy results showed that surface roughness also varied significantly with substrate bias voltage. Films deposited under conditions of -150 $V_b$ (bias voltage) exhibited higher hardness than other films.

• Textile Coloration and Finishing
• /
• v.29 no.1
• /
• pp.18-24
• /
• 2017

Meta-aramid fabric has been widely used as the reinforcement of composites due to its high flame resistance and tearing strength. Functionality such as abrasion resistance of fabric is very important for specialty fabrics used in car racing suits. In this study, to improve abrasion resistance property of meta-aramid fabric, silicon deposition was conducted by utilizing RF magnetron sputtering. The sputtering process parameters effects were investigated as sputtering power and substrate temperature. The obtained results suggest that the silicon deposition on the meta-aramid fabric has obvious effect upon increasing the abrasion resistance, the thermal insulation and the electric resistance condition for silicon deposition was established. In conclusion, the results of this study have made it possible to manufacture meta-aramids with higher abrasion strength.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.30-40
• /
• 1998

We have calculated ultra-low energy silicon-self ion implantations and silicon damages through classical molecular dynamics simulation using empirical potentials. We tested whether the recently developed Environment-Dependent Interatomic Potential(EDIP) was suitable for ultra low energy ion implantation simulation, and found that point defects formation energies were in good agreement with other theoretical calculations, but the calculated vacancy migration energy was overestimated. Most of the damages that are produced by collision cascades are concentrated into amorphous-like pockets. Also, We upgraded MDRANGE code for silicon ion implantation process simulation. We simulated ultra-low energy boron ion implantation, 200eV, 500eV, and 1000eV respectively, and calculated boron profiles with silicon substrate temperature and tilt angle. We investigated that below 1000eV, channeling effect must be considered.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05b
• /
• pp.57-58
• /
• 1992

The NH$_3$oxidation, which forms thermal oxide layer on silicon substrate with pure $O_2$gas added with small amounts of NH$_3$gas, has good interface sates due to activated gettering effect during oxidation. The superiority of interfae state in NH$_3$ oxidation method is not affected by preprocess but by gettering during oxidation. The dramatec reduction fo interface state is conformed with observing OSF when NH$_3$ oxide is annealed in NH$_3$ atmosphere.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.38-41
• /
• 2002

The variation of photoluminescence(PL) properties of Si thin films was investigated by changing deposition temperatures, Si-rich silicon oxide films on p-type (100) Si substrate have been fabricated by pulsed laser deposition(PLD) technique using a Nd:YAG laser. During deposition, the substrates were kept at the temperature range of room temperature(RT) to $400^{\circ}C$. After deposition, samples were annealed at $800^{\circ}C$ in nitrogen ambient, Strong Blue PL has been observed on RT-deposited Si nanocrystallites. When the deposition temperature was increased over $100^{\circ}C$, PL intensities abruptly decreased. The experimental results show the growing mechanism of Si nanocrystallites by PLD.

• Korean Journal of Materials Research
• /
• v.23 no.2
• /
• pp.116-122
• /
• 2013

For fabricating silicon solar cells with high conversion efficiency, texturing is one of the most effective techniques to increase short circuit current by enhancing light trapping. In this study, four different types of textures, large V-groove, large U-groove, small V-groove, and small U-groove, were prepared by a wet etching process. Silicon substrates with V-grooves were fabricated by an anisotropic etching process using a KOH solution mixed with isopropyl alcohol (IPA), and the size of the V-grooves was controlled by varying the concentration of IPA. The isotropic etching process following anisotropic etching resulted in U-grooves and the isotropic etching time was determined to obtain U-grooves with an opening angle of approximately $60^{\circ}$. The results indicated that U-grooves had a larger diffuse reflectance than V-grooves and the reflectances of small grooves was slightly higher than those of large grooves depending on the size of the grooves. Then amorphous Si:H thin film solar cells were fabricated on textured substrates to investigate the light trapping effect of textures with different shapes and sizes. Among the textures fabricated in this work, the solar cells on the substrate with small U-grooves had the largest short circuit current, 19.20 mA/$cm^2$. External quantum efficiency data also demonstrated that the small, U-shape textures are more effective for light trapping than large, V-shape textures.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.30.1-30.1
• /
• 2011

Silicon is one of useful materials in various industry such as semiconductor, solar cell, and secondary battery. The metallic silicon produces generally melting process for ingot type or chemical vapor deposition (CVD) for thin film type. However, these methods have disadvantages of high cost, complicated process, and consumption of much energy. Electrodeposition has been known as a powerful synthesis method for obtaining metallic species by relatively simple operation with current and voltage control. Unfortunately, the electrodeposition of the silicon is impossible in aqueous electrolyte solution due to its low oxidation-reduction equilibrium potential. Ionic liquids are simply defined as ionic melts with a melting point below $100^{\circ}C$. Characteristics of the ionic liquids are high ionic conductivities, low vapour pressures, chemical stability, and wide electrochemical windows. The ionic liquids enable the electrochemically active elements, such as silicon, titanium, and aluminum, to be reduced to their metallic states without vigorous hydrogen gas evolution. In this study, the electrodeposion of silicon has been investigated in ionic liquid of 1-butyl-3-methylpyrolidinium bis (trifluoromethylsulfonyl) imide ([bmpy]$Tf_2N$) saturated with $SiCl_4$ at room temperature. Also, the effect of electrode materials on the electrodeposition and morphological characteristics of the silicon electrodeposited were analyzed The silicon electrodeposited on gold substrate was composed of the metallic Si with single crystalline size between 100~200nm. The silicon content by XPS analysis was detected in 31.3 wt% and the others were oxygen, gold, and carbon. The oxygen was detected much in edge area of th electrode due to $SiO_2$ from a partial oxidation of the metallic Si.