• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.2111-2111
• /
• 2001

A chemoinfometrical method for evaluating the quantitative determination of crystallinity one polymorphs based on fourie-transformed near-infrared (FT-NIR) spectroscopy was established. A direct comparison of the data with the ones collected from using the and compared with the conventional powder X-ray diffraction method was performed. [Method] The pPure a and g forms of indomethacin (IMC) were prepared by reportedusing published methods. Six kinds of standard samples obtained by physically mixing of a and g forms. After the powder X-ray diffraction profiles of samples have been measured, the intensity values were normalized to against the intensity of silicon powder as the as an external standard. The calibration curves for quantification of crystal content were based upon the total relative intensity of four diffraction peaks from of the form g crystal. FT-NIR spectra of six calibration sample sets were recorded 5 times with the NIR spectrometer (BRAN+LUEBBE). Chemoinfometric analysis was performed on the NIR spectral data sets by applying the principal component regression (PCR). [Results] The relation between the actual and predicted polymorphic contents of form g IMC measured using by the X-ray diffraction method shows a good straight linen linear relation., and it has slope of 0.023, an intercept of 0.131 and a correlation coefficient of 0.986. PCR analyses wereis was performed based on normalized NIR spectra sets offer standard samples of known content of IMC g form. IMC. A calibration equation was determined to minimize the root mean square error of the predictionthe prediction. Figure 1 shows a plot of the calibration data obtained by NIR method between the actual and predicted contents of form g IMC. The predicted values were reproducible and had a smaller standard deviation. Figure 2 shows that the plot for the predicted transformation rate (%) of form a IMC to form g as measured by X-ray diffractomeoy against to those as measured by NIR method. The plot has a slope of 1.296, an intercept of 1,109, and a correlation coefficient of 0.992. The line represents a satisfactory correlation between the two predicted values of form g IMC content. Thus NIR spectroscopy is an effective method for the evaluation to the pharmaceutical products of quantitative of polymorph.

• Journal of the Korean earth science society
• /
• v.22 no.3
• /
• pp.208-222
• /
• 2001

Geochemical investigations on suspended amorphous iron oxide material from the Kwangyang gold mine and its surrounding area, Cheonnam, Korea have been carried out. The sediments samples were collected from 11 location along Kwangyang mine area and were air dried and sieved to -80 mesh. These samples consist mainly of iron, silicon and alumina. The Fe$_2$O$_3$ contents ranges from 17.9 wt.% to 72.3 wt.%. The content of Fe$_2$O$_3$ increase with decreasing Si, Al, Mg, Na, K, Mn, and Ti, whereas the contents of Te, Au, Ga, Bi, Cd, Hg, Sb, and Se increase in the amorphous stream sediments. Amorphous stream sediments have been severely enriched for As (up to 54.9 ppm), Bi (up to 3.77 ppm), Cd (up to 3.65 ppm), Hg (up to 64 ppm), Sb (up to 10.1 ppm), Cu (up to 37.1 ppm), Mo (up to 8.86 ppm), Pb (up to 9.45 ppm) and Zn (up to 29.7 ppm). At the upstream site, the Au content (up to 4.4 ppm) in the amorphous stream sediments are relatively high but those contents decrease with distance of mine location. The content of Ag (up to 0.24 ppm) were low in upstream site but those contents increase significantly in the downstream sites. The X-ray diffraction patterns of the samples have virtually no sharp and discrete peaks, indicating that some samples are amorphous or poorly-ordered. The quartz, goethite, kaolinite and illite were associated in amorphous stream sediments. The infrared spectra for amorphous stream sediments show major absorption bands due to OH stretching, adsorbed molecular water, sulfate and Fe-O stretching, respectively.

• 한국해양학회지
• /
• v.5 no.1
• /
• pp.30-36
• /
• 1970

The water quality of the laver bed at Yongwon Ri, Changwon Gun was investigated during the spring and neap tide in March 1970. The effect of tide on the contents of various chemical constituents was irregular and the variation ranges of the contents were narrow. The pH value during flood and ebb tide was a constant of 8.2. The chlorosity range varied from 19.15 to 19.33g/l, the difference of 0.18g/l being comparatively small for coastal waters. The nutrient salts contents varied irregulary with the change in tide, but nitrite and soluble iron were not detected. In local distribution, chlorosity and silicate- silicon contents were found to be more at Sts. 1, 2 and 3 in the eastern area than at Sts. 4, 5 and 6 in the western area, wheras nitrate and ammonia contents were found to be more at Sts. 4, 5 and 6. The nitrate content was especially high, being twice as much as that at Sts. 1, 2 and 3 in the eastern area. In the spring tide, chlorosity was found, on the average, to be as much as 0.06g/l higher than in the neap tide, but the contents of nutrient salts were higher in the neap tide, especially the nitrate content was twice as much. When compared with other selected local laver beds, i.e., the tidal flats of the Nackdong and Somjin rivers, and of Wan Do Gun, the chlorosity level was highest but the nutrient salts contents level was, in general, slightly lower and the variation ranges narrow in the laver bed at Yongwon ri. The nitrate content, in particular was one tenth smaller than the others.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.513-519
• /
• 1998

Zr-Si binary alloys containing 0.01 to O.lwt.%Si were prepared to investigate the effect of Si on the corrosion behavior of Zr. Corrosion test was performed in pure water at 36$0^{\circ}C$ under a pressure of 2660psi for 100days. The alloys containing 0.01 wt. % and 0.05wt. %Si had the black and uniform oxide film and didn't show the transition of corrosion rate. However. the alloys containing O.lwt.%Si had white oxide film and showed the trasition of corrosion rate at 70 days corrosion test. The weight gain increased with the increasing Si content from 0.01 to 0.1 wt.%. The variation of Si contents had no effect on changing the oxide structure but had significant effect on the electrical resistivity of oxide. The electrical resistivity decreased with increasing Si content. The fraction of precipitates in the Zr-Si binary alloys. identified as tetragonal $Zr_{3}$Si increased with increasing Si content. The increase of the volume fraction of precipitates is thought to be responsible for the increase of weight gain due to short circuit effect of precipitate.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.231-239
• /
• 1999

The microstructure of ceramic composite has been found to be governed by the type and amount of the secondary phase, the sintering aid, and the sintering conditions such as sintering temperature, pressure and holing time. Moreover, tribological properties are strongly dependent on microsturcture of composite and operating conditions. In this study, silicon nitride with various amount of magnesia as a sintering aid were prepared and sintered by a hot pressing (HP) technique. Microstructure, mechanical properties (hardness, strength, and fracture toughness), and tribological properties in different environments of $Si_{3}N_{4}$ (in air, water, and paraffine oil) were investigated as a function of MgO content in $Si_{3}N_{4}$. As increasing the amount of MgO in $Si_{3}N_{4}$, the glassy phase in the grain boundaries enlarged the $\beta$-phase elongated grains, and also degraded the Hertzian contact damage resistance. Tribological behaviors in air was seemed to be determined by fracture toughness of $Si_{3}N_{4}$, and those in water and paraffin oil was seemed to be determined by hardness as well as strength. Since glassy grain-boundary phase (MgO) in $Si_{3}N_{4}$ expected to be reacted with water during sliding, such tribochemical reaction reduced wear. In paraffin oil under a higher applied load, the initial sliding dominated wear rate because of Hertzian contact damage.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.310-316
• /
• 2017

This study was analyzed the effects of boron (B), calcium (Ca), silicon (Si) on quality and shelf life of 'Unicorn' cherry tomato at the light red maturity-stage. The storage conditions were modified atmosphere packaging (MAP) by oxygen transmission rate (OTR) packaging film at $5^{\circ}C$, $11^{\circ}C$, and $24^{\circ}C$. Respiration and ethylene production were the lowest in B + Ca + Si -treated tomato fruits. The lowest fresh weight loss and the longest shelf life resulted from the B + Ca + Si treatment. And the firmness was enhanced by B + Ca + Si treatment at harvest time, and it was retained after storage at $5^{\circ}C$, $11^{\circ}C$, and $24^{\circ}C$. Significantly lower soluble solids, lycopene, and color development were found at B + Ca + Si-treated tomato fruits compared with control after storage. Moreover, the highest titratable acidity and vitamin C content were observed in B + Ca + Si-treated tomato fruits after storage. From the above results, it was concluded that B + Ca + Si combined treatment can delay the maturity of cherry tomato after harvesting, and retained the firmness and prolong the shelf life.

• Journal of Adhesion and Interface
• /
• v.9 no.3
• /
• pp.7-13
• /
• 2008

The particulate type silicon carbide (SiC) and fiber type carbon fiber (CF) filler, of similar thermal conductivities, were mixed with polyetheretherketone (PEEK) to investigate the filler effects on the thermal diffusivity. The SiC and CF fillers had a good and uniform dispersion in PEEK matrix. Thermal diffusivities of PEEK composites were measured from ambient temperature up to $200^{\circ}C$ by laser flash method. The diffusivities were decreased as increasing temperature due to the phonon scattering between PEEK-filler and filler-filler interfaces. Thermal diffusivity of PEEK composites was increased with increasing filler content and the thermal conductivities of two-phase system were compared to the experimental results and it gave ideas on the filler dispersion, orientation, aspect ratio, and filler-filler interactions. Nielson equation gave a good prediction to the experimental results of PEEK/SiC. The easy network formation by CF was found to be substantially more effective than SiC and it gave a higher thermal diffusivities of PEEK/CF than PEEK/SiC.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.512-518
• /
• 2001

It has been well known that 6.5wt% Si steel sheets have excellent magnetic properties such as low core loss. high maximum permeability and low magnetostriction. In this work, we studied a method for producing 6.5wt% Si steel sheets using a chemical vapor deposition (CVD) method. The following is the procedure adopted in this work to produce 6.5wt% Si steel sheets; SiCl$_4$ gas is applied onto a low content-Si steel sheet placed in a tube furnace. Silicon atoms resulted from the decomposition of SiCl$_4$ are permeated through the surface of the steel sheet. Finally, by the diffusion process maintaining it under a high temperature the silicon atoms diffuse uniformly into the sheet. Through this process, 6.5wt% Si steel sheets can be obtained. The manufactured Fe-6.5wt% Si steel sheet with a thickness of 0.5mm exhibited a high frequency core loss (W$_{2}$1k/) of 8.92 W/kg. Its permeability increased from 37,100 to 53,300 at 1 tesular(T). The mechanical properties of the manufactured steel sheets were also estimated and the result showed that the workability was significantly improved by annealing in vacuum at 773k. Increased plastic deformation was also observed prior to fracture and the amount of grain boundary rupture was reduced.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.28-35
• /
• 2013

The recycling of the Si/SiC mixture sludge obtained from solar cell industry is very significant, environmentally and economically. The sintering characteristics of Si/SiC mixture sludge was studied for the purpose of recycling. In this study, to understand sintering behavior, SiC content in the Si/SiC mixture was controlled using an air separator. Various Si/SiC mixtures having different SiC contents were sintered using carbon black, clay and aluminum hydroxide as sintering aids. Physical properties of Si/SiC mixture and sintered bodies have been characterized using SEM, XRD, particle size analyzer and apparent density measurement. SEM and particle size analysis result confirmed that the fine particles less than 1 ${\mu}m$ decreased or removed more effectively through the air separator in the case of 95% SiC sample compared than the case of 75% SiC sample or original SiC sample. Further, with addition of the Aluminum Hydroxide, ${\beta}$-cristobalite phase gradually decreased while mullite phase gradually increased. The addition of the carbon black improved the sintering characteristics.

• Journal of the Korean Electrochemical Society
• /
• v.24 no.4
• /
• pp.77-92
• /
• 2021

The energy density of lithium-ion batteries (LIBs) determines the mileage of electric vehicles. For increasing the energy density of LIBs, it is necessary to develop high-capacity active materials that can store more lithium ions within constrained weight. The rapid progress made in cathode technology has realized the utilization of the near-theoretical capacity of cathode materials. In contrast, commercial LIBs have still exploited graphite as active material in anodes since the 1990s. The most promising way to increase anodes' capacity is to mix high-capacity and long-cycle-life silicon oxides (SiOx) with graphite. However, the low initial Coulombic efficiency (ICE) of SiOx limits its content below 15 wt%, impeding the capacity increase in anodes. To address this issue, various prelithiation techniques have been proposed, which can improve the ICE of high-capacity anode materials. In this review paper, we introduce the principles and expected effects of prelithiation techniques reported so far. According to the reaction mechanisms, the strategies are categorized. Mainly, we focus on the recent progress of solution-based chemical prelithiation methods with commercial viability, of which lithiation reaction occurs homogeneously at liquid-solid interfaces. We believe that developing a cost-effective and mass-scalable prelithiation process holds the key to dominating the anode market for next-generation LIBs.