• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.535-540
• /
• 2011

Organic-inorganic hybrid coating solutions were prepared starting from colloidal silica, lanthanum nitrate and ${\gamma}$-glycidoxypropyl trimethoxysilane by the sol-gel method. Also, spiropyran-doped hard coating solutions were prepared by mixing the spiropyran solution, obtained after dissolving spiropyran dye into tetrahydrofuran solvent, with the organic-inorgnic hybrid coating solutions. The spiropyran-doped hard coating solutions were applied as a thin layer to polycarbonate sheets, and their photochromic properties were investigated. The effect of amount of colloidal silica added into the coating solutions was investigated on the photochromic properties of coating films. Both decoloration rate and pencil hardness of the coating films were increased with increasing the amounts of colloidal silica.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2529-2535
• /
• 2013

Sol-gel method was utilized to prepare SPEEK/PWA electrolyte composite membranes. TEOS was used as a precursor and phosphotungstic acid(PWA) as a catalyst for the sol-gel reaction. It was observed through FE-SEM analysis that the PWA and silica nanoparticles were uniformly dispersed into the polymer matrix. The water uptake of SPEEK/PWA/silica composite membranes was less affected by TEOS concentration at higher TEOS contents, while the water uptake decreased as TEOS concentration increased at lower TEOS contents. The proton conductivity of the composite membranes showed similar trend as the water uptake of the composite membranes. The methanol permeability of SPEEK/PWA/silica composite membranes decreased as TEOS concentration increased.

• Membrane and Water Treatment
• /
• v.9 no.5
• /
• pp.317-325
• /
• 2018

Polyvinyl chloride (PVC) ultrafiltration (UF) membrane was modified by silica sol in the coagulation bath during non-solvent induced phase separation (NIPS) process. The effects of silica sol concentrations on the morphology, surface property, mechanical strength and separation property of PVC UF membranes were systematically investigated. PVC membranes were characterized by Fourier transform infrared spectroscopy (FTIR), energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), contact angle goniometry and tensile strength measurement. The results showed that silica had been successfully assembled on the surface of PVC UF membrane. With the increase of silica sol concentration in the coagulation bath, the morphologies of PVC UF membranes changed from cavity structure to finger-like pore structure and asymmetric cross-section structure. The hydrophilicity and permeability of PVC UF membranes were further evaluated. When silica sol concentration was 20 wt.%, the modified PVC membrane exhibited the highest hydrophilicity with a static contact angle of $36.5^{\circ}$ and permeability of $91.8(L{\cdot}m^{-2}{\cdot}h^{-1})$. The structure of self-assemble silica had significant impact on the surface property, morphology, mechanical strength and resultant separation performance of the PVC membranes.

• Resources Recycling
• /
• v.16 no.5
• /
• pp.31-35
• /
• 2007

The formation of silica sol from sodium silicate solution and the growth of silica sols were investigated in this study. The $SiO_2$ content of 2% in sodium silicate solution was proper to oxidize sodium silicate with sulfuric acid. After the removal of sodium ions in sodium silicate solution, the pH of silicate solution had to be controlled above 9 for a stable silicate solution. The silica sol, which size is about 10 nm, could be prepared by heating the mixed solution of sodium silicate and silicate solution removed sodium ions at pH 10 and 80. And the silica sol grew into about 50 nm as silicate solution was added to silica sol solution.

• Journal of the Korean Ceramic Society
• /
• v.26 no.5
• /
• pp.677-681
• /
• 1989

On the preparation of silica glass by sol-gel process, we used fine powder of silica gel to prevent cracking. In this case, the best condition of silica glass preparation is the contents of 10~40wt% seed and the gelation time of solution in contract. The dried gels conversed to silica glass by heat treatment up to 125$0^{\circ}C$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.1037-1041
• /
• 2014

Slurry used for polishing semiconductors processed by exchange, pressurization, and multi-step feeding has been studied to investigate the effect of the size and shape of slurry particles on the oxide CMP removal rate. First, spherical silica sol was prepared by the ion exchange method. The spherical silica particle was used as a seed to grow non-spherical silica sol in accordance with the multi-step feeding of silicic acid by the ion exchange and pressurization methods. The oxide removal rate of both non-spherical silica sol and commercially available slurry were compared with increasing average particle size in the oxide CMP. The more alkaline the pH level of the non-spherical silica sol, the higher was the removal rate and non-uniformity.

• Journal of the Korean Ceramic Society
• /
• v.29 no.5
• /
• pp.357-366
• /
• 1992

Residual organics were considered as impurity in Sol-Gel method. The purpose of this study was to find the conditions to contain as much residual organics as possible in silica gel prepared from TEOS(tetraethylortho-silicate) by Sol-Gel method. Residual organics are to be expected to have reduction effect on synthesizing Si3N4 from silica gel. The results of this study are follows: 1) The maximum content of entrapped carbon was 19.8 wt.%(C/SiO2=0.25 wt.ratio) in silica gel synthesized under the conditions 1.5 fold mole water for incomplete hydrolysis, 2.5 fold mole phenol as a solvent and 0.1 fold mole HCl as a catalyst to TEOS. 2) Silica gel with organics entrapped by Sol-Gel method had a positive effect on the formation of Si3N4 compared with commercial silica gel. 3) Sintered body of synthesized $\alpha$-Si3N4 with Y2O3 and Al2O3 as additives at 175$0^{\circ}C$ in N2 atmosphere showed bending strength, 602$\pm$20 MPa and frature toughness 4.45$\pm$0.15 MPa.m1/2.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.9
• /
• pp.967-972
• /
• 2004

Hardness and surface property of coated gel materials are considerably different according to kinds(particle size/stabilized ion) of colloidal silica(CS), kinds of silanes, content ratio of silane versus CS, and reaction degree in sol solution. We report the properties of sol-gel coating materials in which the factors of reaction are kinds of CS, contents ratio of CS and MTMS, and reaction time of sol. The contact angles of the coated films obtained from the mixed CS system showed a little good relationship with MTMS content increase to those from HSA CS reaction system and the change of contact angle didn't have much effect on reaction time of sol. In the coating films obtained from HSA CS reaction system, the surface was much rough in case of that the content MTMS decreased and the reaction of sol kept long. The surface roughness of films obtained from the mixed CS reaction system showed similar tendency, though its degree was a little different. In synthesis of sol-gel coating materials, we could identify that choice of CS kinds and content ratio of CS and silane were important and it was desirable the reaction time of sol is not long.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.271-276
• /
• 2014

Silica nano-powder (SNP) is an inorganic material able to provide high-performance in various fields because of its multiple functions. Methods used to synthesize high purity SNP, include crushing silica minerals, vapor reaction of silica chloride, and a sol-gel process using TEOS and sodium silicate solution. The sol-gel process is the cheapest method for synthesis of SNP, and was used in this study. First, we investigated the shape and the size of the silica-powder particles in relation to the variation of HCl and sodium silicate concentrations. After drying, the shape of nano-silica powder differed in relation to variations in the HCl concentration. As the pH of the solution increased, so did the density of crosslinking. Initially, there was NaCl in the SNP. To increase its purity, we adopted a washing process that included centrifugation and filtration. After washing, the last of the NaCl was removed using DI water, leaving only amorphous silica powder. The purity of nano-silica powder synthesized using sodium silicate was over 99.6%.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.3
• /
• pp.29-39
• /
• 2022

The engineering characteristics of synthetic polymer-silica sol, which has the effect of reducing leakage, was evaluate and compared with typical grouting material, the water glass-based SGR injection material in this study. The result of the laboratory tests on strength and durability about the synthetic polymer-silica sol showed more than twice as high as LW-based injection materials in uniaxial compressive strength, significantly lower values in shrinkage rate and permeability. The result of pH was less than 8.5 (the drinking water quality standard). As a result of the leaching test, the Na₂O elution amount of the synthetic polymer-silica sol was measured to be 3 to 4 times smaller than that of the water glass grout. These results be assumed that the synthetic polymer-silica sol has better durability and permeability than those of the typical water glass-based grout.