• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.5
• /
• pp.209-213
• /
• 2010

This paper is a study of Car safety network system using sensed data from varied sensors. This hardware will work with various sensors and communication protocols. There are many sensors. Then, I selected 3 sensors for test, which were sonic sensor for distance checking, tilt sensor for rollover and impact sensor for car accident and theft. Also, there are many interfaces for sensor. Therefore I designed hardware to support various sensor interfaces. For instance ADC(Analog to Digital converter), I2C, RS232, RS485, CAN. In this case, sonic sensor have I2C interface, tilt sensor have RS485 interface and Impact sensor have analog interface. In this research, I can gather sensing data from 3 sensors (mentioned above), and sending control signal to other processor with RS232, RS485, CAN communication. So, we can use easily this hardware for many cases of systems, which need sensors.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.6
• /
• pp.35-41
• /
• 2000

This paper describes a merged-capacitor switching (MCS) technique to improve the signal Processing speed and resolution of CMOS analog-to-digital converters (ADCs). The proposed MCS technique improves a sampling rate by reducing the number of capacitors used in conventional pipelined ADCs. The ADC capacitor mismatch can be minimized without additional power consumption, die area, and the loss of sampling rate, when the size of each unit capacitor is increased as much as the number of capacitors reduced by the MCS technique. It is verified that the ADC resolution based on the proposed MCS technique is extended further by employing a conventional commutated feedback-capacitor switching (CFCS) technique.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.12
• /
• pp.155-160
• /
• 2003

Owing to the advances in ADC and DSP technologies, signals in If band, which once had to be processed in analog technology, can new be digitally processed. This is referred to as "Digital IF" or "Digital Radio", which is a preliminary stage of SDR. Applying the digital radio technology to a multi-carrier receiver design, a processing gain is generated through an over-sampling of input data. In the digital receiver, decimation is performed for reducing the computational complexity CIC and half band filter is used together with the decimation as an anti-alising filter. The CIC filter, however, should introduce the roll-off phenomenon in the passband, which causes the receiving performance to be considerably degraded due to the distorted Passband flatness of receiving filter. In this paper, we designed a CIC roll-off compensation filter for W-CDMA digital receiver. The performance of the proposed compensation filter is confirmed through computer simulations in such a way that the BER is minimized by compensating the roll-off characteristics.off characteristics.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.12
• /
• pp.511-517
• /
• 2006

The key issues in high power, high energy applications such as electromagnetic launchers include safety, reliability, flexibility, efficiency, compactness, and cost. To explore some of the issues, a control scheme for a large current wave-forming was designed, built and experimentally verified using a 2.4MJ pulse power system (PPS). The PPS was made up of eight capacitors bank unit, each containing six capacitors connected in parallel. Therefore there were 48 capacitors in total, with ratings of 22kV and 50kJ each. Each unit is charged through a charging switch that is operated by air pressure. For discharging each unit has a triggered vacuum switch (TVS) with ratings of 200kA and 250kV. Hence, flexibility of a large current wave-forming can be obtained by controlling the charging voltage and the discharging times. The whole control system includes a personal computer(PC), RS232 and RS485 pseudo converter, electric/optical signal converters and eight 80C196KC micro-controller based capacitor-bank module(CBM) controllers. Hence, the PC based controller can set the capacitor charging voltages and the TVS trigger timings of each CBM controller for the current wave-forming. It also monitors and records the system status data. We illustrated that our control scheme was able to generate the large current pulse flexibly and safely by experiments. The our control scheme minimize the use of optical cables without reducing EMI noise immunity and reliability, this is resulting in cost reduction. Also, the reliability was increased by isolating ground doubly, it reduced drastically the interference of the large voltage pulse induced by the large current pulse. This paper contains the complete control scheme and details of each subsystem unit.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.5
• /
• pp.413-417
• /
• 2010

Line to ground faults by deterioration of insulators has frequently occurred in power system, and the main cause is surface contamination of the insulators. The contamination of insulator is analyzed by monitoring the surface leakage current flowing them. The suspension insulator is monitored by installation of a zero-phase current sensor(ZCT), but the line-post insulator is impossible to apply the same method because of its large diameter structure. This paper proposed a detection method of surface leakage current for a line-post insulator, and it can easily be applied to new and/or built insulators. The leakage current is indirectly calculated from the potential difference between the metal electrode attached on the surface of insulator and the ground connector. To evaluate the performance of the proposed method, the leakage current is compared as a function of contamination condition controlled by the density of NaCl solution. The leakage current is proportioned to the density of NaCl solution, and the voltage detected by the electrode showed the same trend. From the experimental results, we designed and fabricated a monitoring device which is composed of a detection electrode, signal converter, microprocessor, and ZigBee, and its measurement range is $10{\mu}A{\sim}5mA$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.1-8
• /
• 2009

We designed an ADC that operated upto 500Msamples/sec based on proposed R-string folding block as well as second folding block. The upper four bits are processed in parallel by the R-string folding block while the lower four bits are processed in pipeline structured second folding block to supply digital output. To verify the circuit performance, we conducted HSPICE simulation and the average power consumption was only 1.34mW even when the circuit was running at its maximum sampling frequency. We further measured noise immunity by applying linear ramp signal to the input. The DNL was between -0.56*LSB and 0.49*LSB and the INL was between -0.93*LSB and 0.72*LSB. We used 0.35 microns MOSIS device parameters for this work.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.392-402
• /
• 2020

This paper proposes a solar tracking system without photo-sensors. The system can be classified into four modules: Solar Tracking, MPPT, ESS, and Real-Time Monitoring. Nine solar panels, as a basic unit, are adopted with grid structures of different heights to reduce wind influence and to enable solar tracking without photo-sensors. The low-cost MCU implements MPPT method which generates PWM switching signal for boost converter. The unit of ESS consists of three-series and four-parallel lithium-ion batteries in order to enable monitoring for abnormalities in temperature and electrical characteristics of battery. Four MCUs used in the system consists of two AVR Atmega128, and two Raspberry PI, and they exchanges operation informations. Experimental results of the proposed system show the solar tracking performance, the possibility of on-site and remote monitoring and the convenience of maintenance based on IoT technology.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.10
• /
• pp.910-916
• /
• 2015

A sensorless motor control scheme with conventional back-Electro Motive Force (EMF) sensing based on zero crossing point (ZCP) detection has been widely used in various applications. However, there are several problems with the conventional method for effectively driving sensorless brushless motors. For example, a phase mismatch of 30 degrees occurs between the ZCP and commutation time. Additionally, most of the motor speed/current controls are achieved based on a pulse width modulation (PWM) method, which generates significant noise that distracts the back-EMF sensing. Due to the PWM switching, the ZCP is not deterministic, and thus the efficiency of the motor is reduced because the phase transition points become uncertain. Moreover, the motor driving performance is degraded at a low speed range due to the effect of PWM noise. To solve these problems, an improved back-EMF detection method based on a differential line method is proposed in this paper. In addition, the proposed sensorless BLDC driver addresses the problems by using a variable voltage driver generated from a buck converter. The variable voltage driver does not generate the PWM switching noise. Consequently, the proposed sensorless motor driver improves 1) the signal-to-noise ratio of back-EMF, 2) the operation range of a BLDC motor, and 3) the torque characteristics. The proposed sensorless motor driver is verified through simulations and experiments.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.325-330
• /
• 2012

A single-phase PVPCS(photovoltaic power conditioning system) that contains a single phase dc-ac inverter tends to draw an ac ripple current at twice the out frequency. Such a ripple current may shorten passive elements life span and worsen output current THD. As a result, it may reduce the efficiency of the whole PVPCS system. In this paper, the ripple current propagation is analyzed, and two methods to reduce the ripple current are proposed. Firslyt, this paper presents notch filter with IP voltage controller to reject specific current ripple in single-phase PVPCS. The notch filter can be designed that suppress just only specific frequency component and no phase delay. The proposed notch filter can suppress output command signal in the ripple bandwidth for reducing output current THD. Secondly, for reducing specific current ripple, the other method is feed-forward compensation to incorporate a current control loop in the dc-dc converter. The proposed notch filter and feed-forward compensation method have been verified with computer simulation and simulation results obtained demonstrate the validity of the proposed control scheme.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.68-74
• /
• 2006

We have extracted an optical clock signal from a return-to-zero(RZ) pseudorandom bit sequence(PRBS) and non-return-to-zero(NRZ) PRBS data in a pulsation multi-section laser diode with DFB reflector. The ms timing jitter achieved less than 1 ps for the input 11.727 Gbit/s RZ PRBS and NRZ PRBS data. The PRE data wasconverted from the NRZ data using an NRZ to pseudo-return to zero(PRZ) converter module. The optical clock was extracted from the PRZ data which contains the clock components. Although the input PRZ data gives a timing jitter of 2 ps, the extracted clock has timing jitter of ${\~}$1 ps.