• 제목/요약/키워드: shrinkage rate

검색결과 446건 처리시간 0.036초

신축성 데님 청바지의 패턴 연구 (The Development of Jeans Pattern for Stretch Denim Fabrics)

  • 어미경;서미아
    • 한국의상디자인학회지
    • /
    • 제9권3호
    • /
    • pp.191-203
    • /
    • 2007
  • The purpose of this study was to present a making method of jeans pattern with high fitness after deriving the appropriate shrinkage rate by material and washing process. According to the result of the exterior evaluation of test jeans, all 6 jeans were rated high with scores close to 3.5. Following the evaluation of satisfaction of usage by physical movement, the highest ranking was in the order of walking with normal steps, back bending $90^{\circ}$, chair sitting, climbing stairs and squatting. The shrinkage rate by physical area showed the highest score in the order of pants length, waist circumference, thigh circumference, knee circumference, hem circumference, hips circumference. In addition, the shrinkage rate was higher in warp direction than weft direction after washing finishing. As for the result of addition and reduction of pattern measurements by parts of jeans, waist circumference was $3.1{\sim}5.1cm$, hips circumference was $-1.2{\sim}4.2cm$, thigh circumference was $-0.9{\sim}3.1cm$ and pants length was $3.4{\sim}6.1cm$. That is, this results showed a wide range of addition and reduction according to material and washing finishing.

  • PDF

재유화형 폴리머 분말수지 혼입 폴리머-시멘트 모르타르의 건조수축 및 강도특성 (Drying Shrinkage and Strength Properties of Polymer-Modified Mortars Using Redispersible Polymer Powder)

  • 연규석;주명기;정중호;김성기;이지원
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
    • /
    • pp.533-536
    • /
    • 2005
  • Drying shrinkage and strength of the redispersible SBR and PAE powder-modified mortars were experimentally investigated. Results of the study that the drying shrinkage rapidly increased until 7 days of age and it was then saturated to the value of about $1\~2\times10^{4}$ after 14 days. It turned out that the polymer-cement ratio exerted more influence on the drying shrinkage than the content of powder shrinkage-reducing agent did. Flexural (compressive) strength of the mortar increased (decreased) as the polymer-cement ratio increased and it was 7$\~$11 (23$\~$39) MPa at 7 days of age. The average (maximum) increasing (decreasing) rate turned out to be about 10 (30) $\%$. As in the drying shrinkage case, the polymer-cement ratio exerted more influence on both flexural and compressive strengths than the content of powder shrinkage agent did.

  • PDF

초고강도 콘크리트의 자기수축 및 물리적 특성에 관한 기초적 연구 (A Basic Study on Autogenous Shrinkage and physical property of the Ultra-High-Strength Concrete)

  • 박현;윤기현;조승호;김광기;김우재;정상진
    • 한국건축시공학회:학술대회논문집
    • /
    • 한국건축시공학회 2009년도 춘계 학술논문 발표대회 학계
    • /
    • pp.57-60
    • /
    • 2009
  • In ultra-high-strength concrete, autogenous shrinkage is larger than dry shrinkage due to the consume of a large amount of cement and cementitous material, and this is a factor deteriorating the quality of structures. Thus, we need a new technology for minimizing the shrinkage strain for ultra-high-strength concrete. So, this paper have prepared super-high-strength concrete with specified mixing design strength of over 150MPa and have evaluated a method of reducing autogenous shrinkage by utilizing expander and shrinkage-reducing agent. According to the results of this study, with regard to the change in length by autogenous shrinkage, an expansion effect was observed until the age of seven days. The expansion effect was higher when the contents of the expander material were higher. In addition, ultra-high-strength concrete showed a shrinkage rate that slowed down with time, and the effect of the addition of expander material on compressive strength was insignificant. That is shown that required more database to be accumulated through experimental research for the shrinkage strain of members.

  • PDF

콘크리트 슬래브의 소성수축균열 해석모델 (A Numerical Model for Plastic Shrinkage Cracking of Concrete Slab)

  • 곽효경;하수준
    • 한국전산구조공학회:학술대회논문집
    • /
    • 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
    • /
    • pp.448-455
    • /
    • 2005
  • In this paper, an analytical model for estimation of the time at which the concrete surface begins to dry is introduced to predict whether or not plastic shrinkage cracks occur. First of all, the validity of a consolidation model for bleeding of cement paste proposed by Tan et al. is verified by comparing the analytical results with the experimental results, and used to evaluate the rate and amount of bleed water of concrete. Also an analytical model for evaporation of bleed water which considers the effect of the temperature variation of concrete surface due to hydration heat on the evaporation rate is proposed, and the experimental and analytical results are then compared to verify the validity of the introduced model. In advance, the time at which the concrete surface begins to dry is estimated using above two analytical models, and compared with the experimental results about the time at which plastic shrinkage cracks occur. From the comparison, it is verified that the proposed model can predict the occurrence of plastic shrinkage cracking with comparative precision.

  • PDF

스테인레스강에 대한 전자빔용접과 협개선TIG 용접수축량 비교 (The comparison of weld shrinkage between Electron beam welding and Narrow-gap TIG welding for stainless steel)

  • 김용재;정원회;심덕남;정인철
    • 대한용접접합학회:학술대회논문집
    • /
    • 대한용접접합학회 2004년도 추계학술발표대회 개요집
    • /
    • pp.76-78
    • /
    • 2004
  • The phenomenon of weld shrinkage mainly occurs owing to residual stress by heating, which largely effects on welding quality, Actually as the shrinkage rate depends on the weld deposit amount, so it is desired that the sectional area of weld joint shall be reduced. In this respect the Electron beam welding has more profitable position compare to Narrow-gap TIG welding which is even superior to other arc welding processes. In case of thick austenitic stainless steel the shrinkage rate of Electron beam welding has about $10\%$ of Narrow-gap TIG welding's, which means that residual stress is a lot less than that of Narrow-gap TIG welding. And heat input and welded section area also indicate large difference between two processes.

  • PDF

콘크리트의 Consistency 변화가 소성수축에 미치는 영향 (Influence on the Plastic Shrinkage of Concrete for a Varieties of Consistency)

  • 오무영
    • 한국농공학회지
    • /
    • 제20권1호
    • /
    • pp.4626-4630
    • /
    • 1978
  • The objective of this study is to investigate how the varieties of consistency of fresh concrete influence on the plastic shrinkage in dry condition. The test was conducted under the controlled chamber in which the temperature was kept at 25 ${\pm}$2$^{\circ}C$, the humidity 35 ${\pm}$3%, and the wind velocity 4.0 ${\pm}$0.5m/sec. The results obtained from the test are as follow. 1) The rate of evaporation was highest at 2-3 hour after casting, and decreased gradually. 2) The plastic shrinkage was increased as to the slump values. The shrinkage rate was very highest at 2-4 hour and hardly showed any changes after 6 hour. 3) The recommendation for good cloncrete is that slump value should be as low as possible in construction.

  • PDF

초고강도 콘크리트의 자기수축제어에 관한 연구 -물리적 특성과 길이변화율을 중심으로- (A Study on the Autogenous Shrinkage Control of Ultra.High. Strength Concrete -Focused on physical properties and length variation-)

  • 박현;한다희;조승호;김광기;김우재;정상진
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
    • /
    • pp.653-656
    • /
    • 2008
  • 초고강도 콘크리트는 결합재의 다량 사용에 따라 건조수축보다 큰 자기수축 변형이 나타나며 이는 구조물의 품질을 저해하는 요인으로 작용하여 초고강도 콘크리트의 수축변형을 최소화시키기 위한 기술이 필요하다. 이에 본 연구에서는 설계기준강도 100MPa 이상을 갖는 초고강도 콘크리트를 제조하고 팽창제를 혼입한 초고강도 콘크리트에 대하여 자유수축시험체로 매립형게이지를 통한 수축변형을 측정하였다. 그 결과 팽창제의 혼입으로 초기상태의 콘크리트는 팽창율이 증가하나 장기적 측면에서의 수축율이 둔화되는 것으로 나타났으며, 이를 통한 팽창제를 통하여 수축저감에 관한 효과가 기대된다. 아울러팽창제의 혼입에 따른 압축강도에 미치는 영향은 미미한 것으로 나타났다.

  • PDF

세탁과 건조에 따른 양모 위편성물의 편성조직별 형태 변화 (The effects of knit stitches on the knit construction and the dimensional stability to washing and drying of wool weft-knitted fabrics)

  • 박세은;백성필;박명자
    • 한국의상디자인학회지
    • /
    • 제24권2호
    • /
    • pp.1-10
    • /
    • 2022
  • The purpose of this study is to analyze the structural properties of 100% wool fabrics knitted with various stitch types and to evaluate dimensional stability from shrinkage in wet cleaning and drying. Materials were weft-knitted from twenty-four different stitches with 7 gauge using a computerized flatbed knitting machine. Weight, thickness, density, and length were measured. A domestic washing machine and a tumble dryer were used for the shrinkage test. The results are as follows: Knitted fabrics were divided into 3 groups based on weight per unit area. Porous knits show light weight whilst milano, pintuck, rib stitches belong to the heaviest group. A positive correlation between weight and thickness was found and the same result was obtained for wale density and weight. Dimensional shrinkage of knitted fabrics was increased during repetitive wet cleaning and drying regardless of knit stitches. Especially, fabrics knitted with float, tuck, cable, and links & links stitches samples were contracted more than 15% in the first treatment whereas 2x1 rib stitch showed 1% shrinkage rate. Fisherman and milano stitches contracted in both course and wale direction with similar shrinkage rates. However, porous knits with float and tuck stitches shrank in course direction by 20% as well as cable samples contracted from 5% to 20% after repeated washing and drying. On the other hand, 30% and 15% contraction of wale direction occurred in orderly float and links & links stitches, respectively. Machine dried knits have a higher shrinkage rate than air-dried knits, but the drying method did not affect to the direction of contraction. In conclusion, variations of knit, tuck, and float stitches affect knit construction and dimensional stability from shrinkage in wet cleaning and drying of wool knitted fabrics.

Study on the Engineering Properties of 150MPa Ultra-high Strength Concrete

  • Jung, Sang-Jin;Yoshihiro, Masuda;Kim, Woo-Jae;Lee, Young-Ran;Kim, Seong-Deok;Ha, Jung-Soo
    • 한국건축시공학회지
    • /
    • 제10권4호
    • /
    • pp.113-122
    • /
    • 2010
  • In this study, 150MPa ultra-high-strength concrete was manufactured, and its performance was reviewed. As technically meaningful autogenous shrinkage reportedly occurs at a W/B ratio of 40% or less, although it occurs in all concrete regardless of the W/B ratio, the effects of the use of expansive admixture and shrinkage reducer, or of the friction and restraint of forms that may result in the effective reduction of autogenous shrinkage, were reviewed. As a result, considering the flow and strength characteristics, it was found that the slump flow time was shorter with expansive admixture, and shortest with shrinkage reducer. All specimens with $30kg/m^3$ expansive admixture showed high strength at early material age. Their strength decreased due to the expansion cracks when there was excessive use of expansive admixture, and the use of shrinkage reducer did not influence the change in the strength according to the material age. The expansive admixture had a shrinkage reduction effect of 80%, while the shrinkage reducer had a shrinkage reduction effect of 30%, indicating that the expansive admixture had a stronger effect. It seems that mixing the two will have a synergistic effect. The shrinkage reduction rate was highest when the W/B ratio was 20%. The form suppressed the expansion and shrinkage at the early period, and the demolding time did not significantly influence the shrinkage. The results of the study showed that the excessive addition of expansive admixture leads to expansion cracks, and the expansive admixture and shrinkage reducer have the highest shrinkage reduction effect when they are mixed.

크리깅을 이용한 전자오븐 윈도우 부품용 사출금형의 최적설계 (Optimization of an Electric Microwave Oven Window Using the Kriging Based Approximation Model)

  • 류미라;김영희;이권희;박흥식
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2004년도 추계학술대회
    • /
    • pp.864-869
    • /
    • 2004
  • It is net easy to predict the shrinkage rate of a plastic injection mold in its design process. The shrinkage rate should be considered as one of the important performances to produce the reliable products. The shrinkage rate can be determined by suing the CAE tools in the design produces. However, since the analysis can take minutes to hours, the high computational costs of performing the analysis limit their use in design optimization. In this study, the surrogate models based on the DACE is used in lien of the original models, facilitating design optimization.

  • PDF