• Tribology and Lubricants
• /
• 제10권3호
• /
• pp.39-46
• /
• 1994

In order to investigate the effect of the ceramic reinforcements on the wear properties of aluminum bronze composites, Cu-8wt%Al aluminum bronze alloys reinforced with the Saffil alumina short fiber were produced by the powder metallurgical method and tested by a pin-ondisc wear testing machine. The wear surfaces of the pin specimens and discs, wear debris, and the cross sections of the wear specimens were observed by SEM. The wear mechanism according to various wear conditions and the change of microstructure in the composites were also discussed. In the results, the reinforcement of the composites with alumina short fiber was very effective at the higher applied load over 10N. The material transportation to the counter disc was observed in the alloy specimens without reinforcements. However, the composites reinforced with ceramic particles and fibers showed the resistance against the material transportation.

• Journal of Mechanical Science and Technology
• /
• 제17권5호
• /
• pp.647-653
• /
• 2003

An important class of short-fiber reinforced composites is the sheet molding compound, which is recently developed and currently used in many engineering applications. Fatigue failure of the composites is a subject of major concern in design and cyclic crack propagation is of particular significance in the fatigue life prediction of short fiber composites. However, research on the fatigue behavior of polymer injection weld, especially short glass fiber-filled polymer injection weld, has not been carried out. In this study the analyses of the fatigue crack growth behaviors at weld line and in the bulk are performed based on low cycle fatigue test.

• 한국분말재료학회지
• /
• 제14권6호
• /
• pp.380-385
• /
• 2007

Characteristics of Al-based composites with waste stainless steel short fiber, fabricated by magnetic pulsed compaction and sintering were investigated. The compacts prepared by magnetic pulsed compaction showed high relative density and homogeneous microstructure compared with that by conventional press compaction. The relative density of sintered composites at $430^{\circ}C$ for 1 h exhibited the same value with compacts and decreased with increase in STS short fiber content. The reaction between Al and STS phase was confirmed by the microstructural analysis using EDS. The sintered composites, prepared by magnetic pulsed compaction, showed increased hardness value with increasing STS fiber content. Maximum yield strength of 100 MPa and tensile strength of 232 MPa were registered in the AI-based composite with 30 vol% STS short fiber.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.219-222
• /
• 2004

The effects of short fiber and particle hybrid reinforcement on fatigue crack propagation behaviors in aluminum matrix composites have been investigated. Single and hybrid reinforced 6061 aluminum containing same 20 $Al_2O_3\;volume\%$ with four different constituent ratios of short fibers and particles were prepared by squeeze casting method and tested to check the near-threshold and stable crack growth behavior. The fatigue threshold of the composites increased with portion of particle contents and showed the improved crack resistance especially in low stress intensity range. Addition of particle instead of short fiber also increased fracture toughness due to increase of inter-reinforcement distance. These increase in both fatigue threshold and fracture toughness eventually affected the fatigue crack growth behavior such that the crack growth curve shift low to high stress intensity factor value. Overall experimental results were shown that particle reinforcement was enhanced the fatigue crack resistance over the whole stress intensity factor range.

• 폴리머
• /
• 제33권6호
• /
• pp.530-536
• /
• 2009

고리지방족 에폭시와 산무수물 경화제계에 탄소단섬유(SCF)와 유리단섬유(SGF)를 첨가하여 복합재를 제조한 다음 이들의 열적/기계적 특성을 조사하였다. 열기계분석법으로 측정된 열팽창계수(CTE)의 감소 효과를 보면 낮은 단섬유 함량에서는 두 섬유가 거의 비슷하나, 함량이 증가하면 SCF가 SGF에 비해 훨씬 효과적이었다. SCF 강화 복합재에 대한 CTE 실험값을 이론식에 적용해 본 결과 함량이 낮을 때는 혼합법칙(mixture rule)에 잘 맞으며, 함량이 높아지면 Craft-Christensen 식에 근접하였다. 또한, 유리상($30^{\circ}C$과 고무상($180^{\circ}C$)에서의 저장탄성률은 단섬유를 첨가하였을 때 크게 증가하였다. 전자주사현미경(SEM)으로 파단면을 관찰하여본 결과 이와 같은 결과는 단섬유와 에폭시 매트릭스간의 계면접착력과 밀접한 관계가 있음을 알 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.254-255
• /
• 2017

The aim of this study is to investigate the impact resistant performance of steel short fiber-reinforced cement based composites (SFRCCs) containing 1.0, 1.5, 2.0 and 3.0% volume fraction of steel short fibers subjected to high velocity impact of steel projectile (the diameter of 19.05mm and the mass of 28.13g). The gunpowder impact facility was used for impact tests, and the impact velocity was from about 350 to 700m/s. The specimens were damaged in various failure modes, which are penetration, scabbing, and perforation. Comparing with Plain specimen, SFRCCs have superior capacity on the scabbing limit, and slightly bulged in the back side under the impact velocity of 700m/s. In addition, the impact resistant performance of SFRCCs improved with increase of steel short fiber volume ratio. The fibers play an important role in controlling the local damage of SFRCCs.

• Carbon letters
• /
• 제5권1호
• /
• pp.1-5
• /
• 2004

The effects of fiber surface-treatment and sizing on the dynamic mechanical properties of unidirectional and 2-directional carbon fiber/nylon 6 composites by means of dynamic mechanical analysis have been investigated in the present study. The interlaminar shear strengths of 2-directional carbon/nylon 6 composites sized with various thermosetting and thermoplastic resins are also measured using a short-beam shear test method. The result suggests that different surface-treatment levels onto carbon fibers may influence the storage modulus and tan ${\delta}$ behavior of carbon/nylon 6 composites, reflecting somewhat change of the stiffness and the interfacial adhesion of the composites. Dynamic mechanical analysis and short-beam shear test results indicate that appropriate use of a sizing material upon carbon fiber composite processing may contribute to enhancing the interfacial and/or interlaminar properties of woven carbon fabric/nylon 6 composites, depending on their resin characteristics and processing temperature.

• 한국안전학회지
• /
• 제9권3호
• /
• pp.3-12
• /
• 1994

This study employed the Eshelby's equivalent inclusion method incorporated with mean field theory to investigate the Internal stress of short fiber-reinforced metal matrix composites during static loading and the dynamic finite element analysis by using alternative unit cell model to investigate the impact behaviors during the impact loading. Using the 2124 Al-SiC system as an example, the general effects of parameters such as fiber's aspect ratio, content and modulus were examined.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.258-263
• /
• 1999

In this study, the numerical and experimental investigations were conducted to understand ultrasonic wave propagation and to evaluate the degree of fiber waviness in thick composites nondestructively. The path, energy and traveling time of insonified wave were predicted by adopting the ray and plane wave theories. In the analysis, the composites were assumed to have continuous fiber with sinusoidal waviness in a matrix and were modeled as stacks of infinitesimally short length off-axis elements with varying fiber orientation along the length direction. From the experiments on the specially fabricated thick composite specimens with various degrees of uniform fiber waviness, the energy distributions of received wave were obtain for the various positions of transmitter. It was observed that the energy of wave was converged to the adjacent peaks of fiber waviness. The location where maximum energy of wave was detected from the experiments showed good agreement with the location obtained from theoretical predictions. Finally, the test procedure was Proposed to evaluate fiber waviness in thick composites by considering the energy of wave and relative distance between transmitter and receiver.

• Journal of the Korean Wood Science and Technology
• /
• 제26권2호
• /
• pp.38-44
• /
• 1998

A new device that uses turbulent air for mixing wood fibers with thermoplastic fibers was designed and its mixing effectiveness was evaluated in wood fiber and polypropylene fiber composites. Composites made by the turbulent air mixing (TAM) process performed better than composites made by the conventional Rando-Webber forming or nonwoven web process with an additional needling step. Thus, the TAM process proved to be a simple and efficient method in mixing wood fibers with short thermoplastic fibers for the production of wood fiber and thermoplastic fiber composites.