• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권2호
• /
• pp.141-150
• /
• 2012

Ship damage caused by maritime casualties leads to marine pollution and loss of life and property. To prevent serious damage from maritime casualties, several types of safety regulations are applied in ship design. Damage stability regulation is one of the most important safety issues. Designs of ships for long international voyages must comply with these regulations. Current regulations, however, do not consider the characteristics of the operating route of each ship and reflect only ship size and type of cargo. In this paper, a damage safety assessment was undertaken for a ship carrying radioactive waste in actual wave conditions. Damage cases for safety assessment were constructed on the basis of safety regulations and related research results. Hull form, internal arrangement, loading condition and damage condition were modeled for damage safety simulation. The safety simulation was performed and analyzed for 10 damage cases with various wave heights, frequency and angle of attack on an operating route. Based on evaluation results, a design alternative was generated, and it was also simulated. These results confirmed that damage safety analysis is highly important in the design stage in consideration of the operating route characteristics by simulation. Thus a ship designer can improve safety from damage in this manner.

• 수산해양기술연구
• /
• 제50권3호
• /
• pp.378-384
• /
• 2014

Trawlers are divided into stern and side types by the method of shooting and hauling net, but the latter is difficult to find beside Korea. In East Sea of Korea, the side type used to be in early 2000's, but it improved to stern type because of its inefficient operating method. The aims of this paper is to make clear the stability of the side trawler in the East Sea, and then confirm whether it satisfy the IMO rule or not, the degree of the transverse inclining angle of the ship when hauling net at hull side. In results, the stability of the ship in initial inclining range satisfied the IMO rule and the domestic rule, but not satisfied those rule in over the range. The limit load of the ship that was coincide with the angle of beam end in hauling net at side was about 26 tons, 18 tons in normal sea condition and storm warning condition respectively. The transverse inclining angles of the ship in hauling net were much higher from 3.3 to 5.5 times than the longitudinal inclining angle of the stern trawler, although those angles were slightly changed with depending on the loading and sea condition.

• 드라이브 ㆍ 컨트롤
• /
• 제10권4호
• /
• pp.14-21
• /
• 2013

The numerical analysis of the automatic ship mooring system which was equipped in the ship for trying to berth at the pier was performed in this study. The automatic ship mooring using hydraulic winch was a new method that had not need to change the existing devices and to help a pilot ship of outside. The numerical results of the proposed mooring system including ship motion were that the speed and rolling phenomenon of ship was affected by changing in the ship weight and affected the slope maintenance and yaw degree of ship if there has a trim of stern. Also, a static force of ship at the initial movement was important to calculate the mooring power. The moving force and inertial force of ship on the vertical direction was confirmed for the mooring stability. Therefore, the power and velocity of hydraulic mooring winch should be determined by considering the significant characteristics such as weight, velocity, inertial force and moving force of ship.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2018년도 공동국제학술발표회
• /
• pp.44-44
• /
• 2018

• 대한조선학회논문집
• /
• 제31권3호
• /
• pp.65-79
• /
• 1994

본 연구에서는 선미벌브의 채택이 유체력 특성 및 조종성능에 미치는 영향에 관해서 실험적으로 고찰하였다. 연구방법으로서는 일반선미 형상과 선미벌브 형상을 가지는 각각의 모형선을 공시선으로, 회류수조에서 조종성 관련 구속모형시험을 실시하여 양 선형의 차이에 기인하는 유체력 특성과 조종성능을 비교, 검토하였다. 연구 결과, 선미벌브를 채택함으로써 침로안정성은 나빠지지만 선회력이 향상됨을 확인하였고, 이러한 조종성능의 특성과 유체력 특성과의 상관관계를 규명하였다.

• 한국해양공학회지
• /
• 제36권3호
• /
• pp.143-152
• /
• 2022

To reach a port, a ship must pass through a shallow water zone where seabed effects alter the hydrodynamics acting on the ship. This study examined the maneuvering characteristics of an autonomous surface ship at 3-DOF (Degree of freedom) motion in deep water and shallow water based on the in-port speed of 1.54 m/s. The CFD (Computational fluid dynamics) method was used as a specialized tool in naval hydrodynamics based on the RANS (Reynolds-averaged Navier-Stoke) solver for maneuvering prediction. A virtual captive model test in CFD with various constrained motions, such as static drift, circular motion, and combined circular motion with drift, was performed to determine the hydrodynamic forces and moments of the ship. In addition, a model test was performed in a square tank for a static drift test in deep water to verify the accuracy of the CFD method by comparing the hydrodynamic forces and moments. The results showed changes in hydrodynamic forces and moments in deep and shallow water, with the latter increasing dramatically in very shallow water. The velocity fields demonstrated an increasing change in velocity as water became shallower. The least-squares method was applied to obtain the hydrodynamic coefficients by distinguishing a linear and non-linear model of the hydrodynamic force models. The course stability, maneuverability, and collision avoidance ability were evaluated from the estimated hydrodynamic coefficients. The hydrodynamic characteristics showed that the course stability improved in extremely shallow water. The maneuverability was satisfied with IMO (2002) except for extremely shallow water, and collision avoidance ability was a good performance in deep and shallow water.

• 한국항해학회지
• /
• 제15권2호
• /
• pp.1-11
• /
• 1991

The ship's magnetic compass even if corrected is feasible to indicate the erroneous information due to the change of this ship's magnetism. But if the north-seeking sensor of the transmitting magnetic compass system is located where the effect of the ship's magnetism is the least , that problem is expected to be removed. In this paper, as a basic research to enhance the accuracy and the stability of the ship's magnetic compass by placing the north-seeking sensor at the adequate location, the theoretical model for the overall ship's magnetism were studied from the macroscopic viewpoint, The parameters of the theoretical model were determined by the least square method on the assumption that the overall magnetism of a ship can be regarded as that of the prolate spheroidal magnetic body. The agreement between the modelled and the observed values was found to be good.

• 수산해양기술연구
• /
• 제56권3호
• /
• pp.238-245
• /
• 2020

In this study, a motion control problem for the vessel towed by towing ship on the sea is considered. The towed vessel does not have self-control capabilities such that its course stability totally depends on the towing ship. Especially, in the narrow canal, river and congested harbor area, extreme tension is required during the towing operation. The authors, therefore, propose a new control system design method in which the rudder is activated to provide its maneuverability. Based on the leader following system configuration, a nonlinear mathematical model is derived and a backstepping control is designed. By experiment results with nonlinear control framework, the usefulness and effectiveness of the proposed strategy are presented.

• 한국항해항만학회지
• /
• 제26권1호
• /
• pp.1-7
• /
• 2002

전복한 저건현 내항 탱커의 사고 원인을 조사하기 위하여 복원성에 영향을 미치는 자유표면영향과 저건현 선박에서 발생하는 해수침입, 침수침하 현상에 대하여 알아보았다. 피리고 선회시에 발생하는 경사 모멘트륵 계산하고 사고 선박의 경사 모멘트를 추정하였다. 이상의결과로부터 사고 선박의 복원성 상실에 의한 전복 원인을 고찰하였다.

• 대한조선학회논문집
• /
• 제51권2호
• /
• pp.154-161
• /
• 2014

Naval ships have hull appendages which are more exposed to the outside because of its small block coefficient compared with commercial ships. These exposed hull appendages like skeg, strut and shaft line affect the maneuverability of a ship. The effect of hull appendages has considered at initial design stage to estimate more accurate maneuverability. In this paper, sensitivity analysis is used to analyze the effect on maneuverability by hull appendages. 3 DOF maneuvering equations based on Mathematical Modelling Group (MMG) model are used and propeller & rudder model are modified to reflect the characteristics of twin propeller & twin rudder. Numerical maneuvering simulations (Turning test, Zig-zag test) for benchmark naval vessel, David Taylor Model Basin (DTMB) 5415 are performed. In every simulation, it is calculated that stability indices and maneuverability characteristics (Tactical Dia., Advance, 1st Overshoot, Time of complete cycle) with respect to the parameters (area times lift coefficient slope, attachment location) of hull appendages. As a result, two regression formulas are established. One is the relation of maneuverability characteristics and stability indices and the other is the relation of stability indices and hull appendages.