• Journal of Welding and Joining
• /
• 제18권2호
• /
• pp.69-76
• /
• 2000

Formation of the weld defect, such as a blowhole and a pit in lap-jointed fillet arc welds has been a serious problem in arc welding Zn-coated steel sheet. In this study, the relationship among welding conditions, welding materials and defect formation was investigated in order to minimize these defects in the CO₂welds. In addition, the arc stability of the commercial welding wires was evaluated for revealing their effects on defect formation. Main conclusions obtained are as follows: 1) There was no difference between shear tensile strength of the sound welds and that of the welds with blowholes whose diameters are less than 0.5mm. However, the welds with blowholes whose diameters are equal or large than 0.5mm and pits exhibited tensile strength 10∼ 20% and 30∼40% lower than that of the sound welds respectively. 2) The optimum welding condition to effectively prevent or reduce the weld defects formation are as follows: -The welding variables of 220A-23V-100cm/min and 120A-19V-30cm/min were recommended for minimizing the weld defects. -The gap between the two sheets at the lap-joint should be controlled to more than 0.2mm. -Solid wire was less susceptible to the formation of the weld defects than the flux-cored wire. -The low welding current condition produced less weld defects than the high welding current condition. 3) One of the reason why the amount of the defect was reduced at the low welding current was the gas discharging by the active agitation of the molten pool, due to an increasing in the number of the short circuit.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.611-614
• /
• 2005

In this paper, investigated is the relationship between the formation temperature and the thermal stability of Ni silicide formed with Ni-V (Nickel Vanadium) alloy target. The sheet resistance after the formation of Ni silicide with the Ni-V showed stable characteristic up to RTP temperature of $700\;^{\circ}C$ while degradation of sheet resistance started at that temperature in case of pure-Ni. Moreover, the Ni silicide with Ni-V indicated more thermally stable characteristic after the post-silicidation annealing. It is further found that the thermal robustness of Ni silicide with Ni-V was highly dependent on the formation temperature. With the increased silicidation temperature (around $700\;^{\circ}C$), the more thermally stable Ni silicide was formed than that of low temperature case using the Ni-V.

• Corrosion Science and Technology
• /
• 제23권3호
• /
• pp.221-227
• /
• 2024

During hot stamping of hot-dip zinc-coated steel sheets such as hot-dip galvanized steel sheets and hot-dip galvannealed steel sheets, an oxide mainly composed of ZnO is formed on the sheet surface. However, excessive formation of ZnO can lead to a decrease in the amount of metal Zn in the coating layer, decreasing the corrosion resistance of hot-stamped members. Therefore, it is important to suppress excessive formation of ZnO. While the formation of Al oxides and Mn oxides along with ZnO layer during the hot stamping of hot-dip zinc-coated steel sheets can affect ZnO formation, crystal structures of such oxides have not been elucidated clearly. Thus, this study aimed to analyze structures of oxides formed during hot stamping of hot-dip galvannealed steel sheets using transmission electron microscopy. Results indicated the formation of an oxide layer comprising ZnAl₂O₄ at the interface between ZnO and the coating layer with Mn₃O₄ at the outermost of an oxide layer.

• 소성∙가공
• /
• 제18권2호
• /
• pp.116-121
• /
• 2009

Formability and other mechanical properties of sheet metals are strongly dependent on the texture. It was studied to improve the formability of the Al alloy(AA3003) sheets which were rolled under the non-lubrication condition and subsequent heat treated. In the non-lubrication rolled and subsequent heat treated Al alloy sheet, the variation of the plastic strain ratios were investigated in this study. Non-lubrication rolled Al sheets showed a fine grain size and after subsequent heat treated specimens showed that the $\beta$-fiber texture component was increased. The plastic strain ratios of the non-lubrication rolled and subsequent heat treated Al alloy sheets were about two times higher than those of the original Al sheets. These could be related to the formation of $\beta$-fiber texture components through the non-lubrication rolling and subsequent heat treatment in Al sheet.

• 소성∙가공
• /
• 제13권4호
• /
• pp.365-373
• /
• 2004

The sheet formability of single AA5182 sheets and sandwich sheets comprising of AA5182/polypropylene/AA5182 (AA/PP/AA) was studied. Rolling without lubrication and subsequent recrystallization annealing led to the formation of favorable ｛111｝//ND fiber textures in AA5182 sheets, which provided a higher plastic strain ratio of $R_m=1.5$. $R_m$ value of 1.58 was obtained in the AA/PP/Ah sandwich sheet sample. Furthermore, a proper combination of the sample direction of the upper and lower skin sheet gave rise to an optimization of the sheet formability of the sandwich sheets.

• 펄프종이기술
• /
• 제38권4호
• /
• pp.68-75
• /
• 2006

Electromagnetic shielding sheet using the carbon and wood fiber mixture was manufactured in an effort to develop an electromagnetic shielding packaging material. Carbon fibers were cut into 5, 10, and 15 mm using the automatic cutting device and blown and dispersed using compression air passed through the fine nozzle. Then carbon fibers were slurried with water (0.1% consistency), and softwood kraft pulp along with cone starch were added. The wet mats were manufactured by dewatering in modified hand-sheet machine. The wet mats were pressed upto $4kgf/cm^2$ in the carbon and wood fiber mixture mat press. The wet mats were dried in the automatic controlled plate dryer. Investigation on the formation and surface structure of the newly developed carbon and wood fiber mixture electromagnetic shielding sheet were carried out using the scanning electron microscopy and the image analyzer. Finally electromagnetic shielding characteristics of the newly developed carbon and wood mixture sheet were measured using net-work analyser. The result was promising in the light of the fact that this method could open a new way to substitute the expensive imported electromagnetic shielding sheet.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.413-416
• /
• 2006

Two clad composites of five ply sheets comprising STS430/AA3003/AA3003/AA3003/STS430 and STS430/AA3003/STS430/AA3003/STS430 were produced by roll cladding at $350^{\circ}C$. In order to clarify the deformation behavior and strain states in the composites during roll cladding, the variation of individual sheet thickness and the evolution of through thickness textures and microstructures of the composites were investigated. The thickness reduction of each sheet depended on the location of the sheet and on the strength of each sheet in the composites. In order to elucidate the evolution of textures and microstructures in AA3003 sheets, the strain states in AA3003 sheets during roll cladding were calculated by FEM. The formation of shear textures and fine grains in AA3003 sheet was discussed in terms of the strain states in each sheet layer. Finally, the strain states extracted from the FEM were verified by texture simulations

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.64-76
• /
• 1997

This paper deals with development of brackets by using aluminum alloy sheets which is indispensable for weight reduction of autobody. The press formability of aluminum alloy sheet is estimated by means of tensile test, V bending test, sample manufacturing test and photograph of microstructure. The results show that the elongation, strength, work hardening exponent, plastic anisotropy coefficient of Al 6***series are better than those of Al 5***series, but for general press formability, Al 5***series are better than Al 6***series due to lower yield strength. Since most of mechanical properties of aluminum sheet are generally inferior to those of cold-rolled steel sheet, shape fixability and press formability of aluminum sheet are very poor. For making components of autobody by use of die for steel sheet application, it is essential that die should be nodified for least bending and stretching. With the modified die for aluminum, it could be possible to make brackets, the component of autobody. Microstructure of Al 5***series has fine grain and small the 2nd phase and that of Al 6***series has relatively coarse grain. Therefore, it seems that fine grain and small the 2nd phase of Al 5***series is one of the factor of lower yield strength, resistance to stamping work, formation of Luder's line.

• 무역상무연구
• /
• 제63권
• /
• pp.3-24
• /
• 2014

This paper focuses on the formation of contract under CISG through the case by the Korean court. Under the CISG, an offer means that a proposal for concluding a contact constitutes the offer, if it is sufficiently definite and indicates the intention of the offeror to be bound in case of acceptance. An acceptance is statement made by or other conduct of the offeree indicating assent to an offer, and this statement purports to be an acceptance but contains additional or different terms which do not materially alter the terms of the offer constitutes an acceptance. In practice, parties negotiate for lots of contract terms to conclude the contract, and the last reply indicating of assent which is made by statement or other conduct to a proposal for concluding a contract would be an acceptance. At this time the most important factor is the intention of parties whether they intend the offer or the acceptance, Purchase order by buyer or Offer Sheet by seller would be understand as condition precedent for the formation of contract. Nevertheless, keep in mind that the Korean court is consistent in the way Purchase order by buyer or Offer Sheet by seller is an acceptance to conclude contract.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.1069-1072
• /
• 2003

Germane-sillicide phase formation on S $i_{0.25}$G $e_{0.75}$ with Ni 100$\square$, Co 10$\square$/Ni 100$\square$ and Ni 50$\square$/Co 10$\square$/Ni 50$\square$ layer was studied by sheet resistance and Field Emission Scanning Electron Microscopy(FESEM). Thermal stability of nickel germane-silicide is found to be improved by sputtering Ni/Co/Ni on the SiGe. After annealing at 600, 650, $700^{\circ}C$, 30min., the nickel germane-silicide formed by Ni 50$\square$/Co 10$\square$/Ni 50$\square$ layer achieved a sheet resistance less than 17ohms/sq.(almost the same to the value before furnace annealing for 30min.) , while the process of the other two ways result in high sheet resistance and even sheet resistance fail due to Ge segregation.ion.