• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.7-12
• /
• 2009

Coating brittle intermetallic compounds on metal can enlarge the range of their use. It is found that intermetallic compound coating layers made by only combustion synthesis in an electric furnace have porous multi-phase structures containing several intermediate phases, even though the coating layers show good wear resistance. In this study, dense $Ni_{3}Al$ single phase layer corresponding to the initial composition of the mixed powder is coated on two different ferrous materials by the diffusing treatment after combustion synthesis. After- ward, sliding wear behaviors of the coating layer are evaluated in comparison with that of the coating layer with porous multi-phase structure made by only combustion synthesis. As a result, the wear properties of the coating layer composed of dense $Ni_{3}Al$ single phase are considerably improved at the range of low sliding speed com- pared with that of the coating layer with porous multi-phase structure, particularly in the running-in wear region. This is attributed to the fact that wear of the coating layer is progressed by shearing as a sequence of adhesion, not by occurring of pitting on the worn surface due to having dense structure without pores.

• Geomechanics and Engineering
• /
• 제7권2호
• /
• pp.213-231
• /
• 2014

An elastoplastic model for structured clays, which is formulated based on the fact that the difference in mechanical behavior of structured and reconstituted clays is caused by the change of fabric in the post-yield deformation range, is present in this paper. This model is developed from an elastoplastic model for overconsolidated reconstituted clays, by considering that the variation in the yield surface of structured clays is similar to that of overconsolidated reconstituted clays. However, in order to describe the mechanical behavior of structured clays with precision, the model takes the bonding and parabolic strength envelope into consideration. Compared with the Cam-clay model, only two new parameters are required in the model for structured clays, which can be determined from isotropic compression and triaxial shear tests at different confining pressures. The comparison of model predictions and results of drained and undrained triaxial shear tests on four different marine clays shows that the model can capture reasonable well the strength and deformation characteristics of structured clays, including negative and positive dilatancy, strain-hardening and softening during shearing.

• 방사성폐기물학회지
• /
• 제20권2호
• /
• pp.209-229
• /
• 2022

This work provided a review of three techniques-(1) spectrochemical, (2) electrochemical, and (3) spectroelectrochemical-for molten salt medias. A spectroelectrochemical system was designed by utilizing this information. Here, we designed a spectroelectrochemical cell (SEC) and calibrated temperature controllers, and performed initial tests to explore the system's capability limit. There were several issues and a redesign of the cell was accomplished. The modification of the design allowed us to assemble, align the system with the light sources, and successfully transferred the setup inside a controlled environment. A preliminary run was executed to obtain transmission and absorption background of NaCl-CaCl₂ salt at 600℃. It shows that the quartz cuvette has high transmittance effects across all wavelengths and there were lower transmittance effects at the lower wavelength in the molten salt media. Despite a successful initial run, the quartz vessel was mated to the inner cavity of the SEC body. Moreover, there was shearing in the patch cord which resulted in damage to the fiber optic cable, deterioration of the SEC, corrosion in the connection of the cell body, and fiber optic damage. The next generation of the SEC should attach a high temperature fiber optic patch cords without introducing internal mechanical stress to the patch cord body. In addition, MACOR should be used as the cell body materials to prevent corrosion of the surface and avoid the mating issue and a use of an adapter from a manufacturer that combines the free beam to a fiber optic cable should be incorporated in the future design.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.15-21
• /
• 1997

This study is performed for investigating the effects of stripping and counter punching forces on shearing characteristics in fine blanking of T-shaped products, such as camber, burr-height and dimensional accuracy, etc by experiments. Conventional hydraulic press is used for experiments so that both the stripping force and counter punching force can be arbitrarily adjusted by another hydraulic unit connected to the fine blanking die. Specimens are selected as hot rolled steel sheet and carbon steel sheet commonly used in auto- mobile company. Based on the experimental results, both the dimensional accuracy and the burr height are not influenced by the stripping and counter punching forces, wherease the camber height representing dish- shaped deflection is much influenced by them, it can be seen through this study that the finely cut surface of T-shaped blank can be obtained even in conventional hydraulic press if additional equipments and specially designed die are employed.

• 치위생과학회지
• /
• 제13권4호
• /
• pp.487-492
• /
• 2013

본 연구는 지르코니아 코어 표면처리 방법에 따른 코어와 도재와의 결합기전을 파악하여 도재 수복물의 문제점을 개선하고자 도재와 동일한 구조의 코어를 제작한 후 코어 표면의 거칠기 처리와 liner 적용 방법을 각각 달리한 4개 군의 전단결합강도의 차이를 분석한 바 다음과 같은 결론을 얻었다. 1. 코어의 표면 거칠기 처리 여부는 표면조도에 영향을 주었다(p<0.001). 2. 지르코니아 코어 표면을 표면 거칠기와 liner를 도포한 군(SLT군)이 23.19 MPa로 가장 높았고, 표면 거칠기만 적용한 군(ST군)이 21.17 MPa였으며, liner만 적용한 군(LT군)은 20.53 MPa였고, 표면 비처리 군(NT군)이 16.46 MPa으로 가장 낮은 값을 나타내(p=0.176) 표면처리에 따른 전단 결합강도에 차이가 있을 가능성을 나타냈다. 또한 표면 거칠기와 liner를 도포한 군(SLT군)과 표면 비처리 군(NT군)에서 두 군 간의 차이는 통계적으로 유의하였다(p<0.05). 3. 계면상태는 SLT군이 ST군과 LT군, NT군에 비해 도재결합의 응집된 상태를 나타냈다. 코어의 표면처리 특히 거칠기 처리는 지르코니아 코어와 도재의 물리적 결합 즉, 전단결합강도를 높일 수 있는 의미있는 과정임을 확인하였다.

• 한국농공학회지
• /
• 제28권2호
• /
• pp.63-73
• /
• 1986

The model was developed by applying the principles of Bacot and Vidal to measure the behavior of deformation of the reinforced earth wall, and various tasts were performed by using the plastic fabric filter and the galvanized steel plate as a strip. The results obtained are as follows; 1. When the reinforced earth wall is deformed by the load, the strip is completely reinforced by the backfill materials and changed to the rigid block state, under the state of failure which permits sliding only, the next theoretical equation is formed. (H/L) . tan$\theta$ [cosO-sinOtanO] =2sinO[tan($\theta$ +0) +tanO] 2.The degree of the mutual reinforcement of the backfill material and the strip depend on the physical characteristics of the each material especially the angle of shearing resistance of the backfill material is desirable over 20$^{\circ}$ and, if it is over 400, its function could be a maximum. 3.The distribution of the maximum tensile strain of the reinforcement is changing with the height of reinforced earth wall, and when the height from bottom of the reinforced earth wall is 1.85 to 3. 35m, the maximum tensile strain appears at 2m from the skin element. The maximum tensile strain is increased by the depth of the reinforced earth wall from surface, and increased with the lapse of time after construction. 4.The failure surface of the reinforced earth wall by the concrete skin was about 60$^{\circ}$and the failure behavior of the reinforced earth wall in which the fabric filter was buried was slow, and so the pore pressure could be decreased. 5.It is possible to construct the fabric retained earth wall by the plastic fabric filter only. And the reinforcing effect between the steel plate and the plastic fabric filter is not largely different. however, in the aspect of the economic durability, the plastic fabric filter is more advantageous. 6.The reinforcing action mainly depends on the width and the length of the reinforcing materials, if possible, the full width is advantageous to enlarge the contact area with backfill. but considering the economic aspect, it is neccessary to develop the method controlling the space of the strip.

• 대한치과교정학회지
• /
• 제42권1호
• /
• pp.17-22
• /
• 2012

Objective: To study and compare the effects of different demineralization-inhibition methods on the shear bond strength (SBS) and fracture mode of an adhesive used to bond orthodontic brackets to demineralized enamel surfaces. Methods: Eighty freshly extracted, human maxillary premolars were divided into 4 equal groups and demineralized over the course of 21 days. Brackets were bonded to the demineralized enamel of teeth in Group 1. In Group 2, bonding was performed following resin infiltration ($ICON^{(R)}$, DMG, Hamburg, Germany). Before bonding, pre-treatment with acidulated phosphate fluoride (APF) or solutions containing casein phosphopeptide-amorphous calcium phosphate with 2% neutral sodium fluoride (CPP-ACP/wF) was performed in Groups 3 and 4, respectively. The SBS values of the brackets were measured and recorded following mechanical shearing of the bracket from the tooth surface. The adhesive remnant index (ARI) scores were determined aft er the brackets failed. Statistical comparisons were performed using one-way ANOVA, Tukey's post-tests, and G-tests. Results: Significant differences were found in some of the intergroup comparisons of the SBS values (F = 39.287, p < 0.001). No significant differences were found between the values for the APF-gel and control groups, whereas significantly higher SBS values were recorded for the resin-infiltrated and CPP-ACP/wF-treated groups. The ARI scores were also significantly different among the 4 groups (p < 0.001). Conclusions: Tooth surfaces exposed to resin infiltration and CPP-ACP/wF application showed higher debonding forces than the untreated, demineralized surfaces.

• 한국수산과학회지
• /
• 제44권1호
• /
• pp.31-36
• /
• 2011

This study developed a normal temperature-circulatable retort-sterilized crab analog (RSCA) with a long shelf-life by retort sterilization. We examined the optimum sterilization conditions and quality characteristics of the RSCA. A central composite design for response surface methodology (RSM) was adopted to optimize of the retort sterilization. The central composite design consisted of 11 samples: four factorial points, four star points, and three central points. The sterilization temperature and $F_0$-value for retort sterilization were the independent variables, and the shearing force, whiteness, and sensory score for texture were the dependent variable. The RSM analysis of the multiple response optimization for the RSCA using the Minitap statistical programing gave an $F_0$-value of 3.3 min. at $117.5^{\circ}C$. The RSM analysis also indicated that the sterilization temperature during retort sterilization was the most influential factor, while the $F_0$-value had little effect on the quality of the RSCA. The moisture, pH and volatile basic nitrogen contents of the RSCA product were 73.1%, 7.3 and 17.2 mg/100 g, respectively, and viable cells count was >18 CFU/g. And sensory quality characteristics of this RSCA was similar to those of a commercial crab analog.

• 터널과지하공간
• /
• 제11권3호
• /
• pp.225-236
• /
• 2001

암반 절리면의 거칠기는 전단강도 및 변형거동에 가장 중요한 영향을 미치는 요소 중의 하나이다. 절리면은 전단변형이 발생하는 동안 손상을 받게 되고 이에 따라 거칠기각은 연속적으로 낮아진다. 절리면의 수직팽창성과 강도 경화 및 연화현상도 거칠기의 변화와 관련이 있는 것으로 이해되고 있다. 따라서 절리면의 거칠기의 변화를 효율적으로 반영시킬 수 있는 수치해석 모델의 개발이 중요하다. 이 연구에서는 탄소성이론을 바탕으로 거칠기 변화를 고려할 수 있는 탄소성 응력-변형 증분식을 유도하여 절리면 거질기 변화가 절리면 전단거동에 미치는 영향을 정량적으로 평가하는데 이용하였다. 유도된 탄소성 증분식을 검증하기 위하여 수치 주기전단시험을 실시하였다. 수치시험결과 개발된 탄소성 증분식은 거친 절리면의 주기전단시험에 나타나는 일반적인 현상들을 모사하는데 효과적임을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제42권1호
• /
• pp.58-67
• /
• 2014

울진산 금강송의 재질특성 조사의 일환으로 기계적 성질을 조사하였다. 종압축강도는 $36.2N/mm^2$로 국산 소나무재와 잣나무재보다 다소 낮은 값을 나타내었다. 수로부터의 거리에 따른 종압축강도는 수에서 60 mm 떨어진 지점에서 최대값을 나타내었다. 휨강도는 $76.5N/mm^2$로 나타났으며, 국산 소나무재와 잣나무재보다 다소 높은 값을 나타내었다. 그리고 수로부터 60 mm 떨어진 지점에서 최대값을 나타내었다. 전단강도는 높은 비중을 나타내었던 수 부근에서 $10.4N/mm^2$로 최대값을 나타내었으며, 80 mm 지점에서 $9.1N/mm^2$로 최소값을 나타내었다. 표면경도는 횡단면이 $43.7N/mm^2$, 방사단면이 $12.0N/mm^2$, 접선단면이 $13.7N/mm^2$으로 나타났다. 이러한 결과는 비슷한 비중을 나타낸 소나무의 표면경도 값과 유사하다. 금강송의 기계적 성질은 비슷한 비중을 가지는 소나무과 수종인 소나무 및 잣나무와 비슷하였다. 그리고 금강송의 기계적 성질은 평균연륜폭보다 비중에 의해 더욱 큰 영향을 받는다는 것을 확인할 수 있었다.