Structural insulated panels, which are structurally performed panels consisting of a plastic insulation bonded between two structural panel facings are one of emerging products with a viewpoint of its energy and construction efficiencies. These components are applicable to fabricated wood structures. By now, there are few technical documents regulated structural performance and engineering criteria in domestic market. This study was conducted to suggest fundamental reports such as racking resistance, axial capacity, transverse load capacity, and lintel load capacity for SIPs. Test results showed that maximum load was 44.3kN, allowable load was 14.7kN for racking resistance, and that maximum load was 137.6kN, allowable load was 37.4kN/m for axial compression capacity. For transverse load capacity, test results showed $10.3kN/m^2$ of maximum load, $3.4kN/m^2$ of allowable load. For lintel load capacity for SIPs dependent to lengths, allowable loads were 20.4kN for 600mm long lintel, 23.9kN for 1,200mm long lintel, 19.3kN for 1,800mm long lintel, and 2,400mm long lintel had 14.1kN of allowable load. In the near future, when the allowable load for wall application is established, SIPs is considered to substitute the existent post-and-lintel construction to bearing wall structure.
원자력발전소 구조물을 포함하여 플랜트 구조물에서는 사용 중 설비보강을 위하여 벽체 및 슬래브에 관통부를 신설하는 경우가 빈번히 발생하고 있으며, 관통부 설치작업 중에 철근이 절단되는 사례가 일부 발생하고 있다. 이 관통부들은 설계 또는 건설 단계에서 고려된 것이 아니므로 설치 중 발생한 철근의 절단은 사실상 구조물의 손상이기 때문에, 관통부 주변 응력 전이범위 또는 유효폭을 고려한 구조물의 건전성 평가가 필요하다. 본 연구에서는 가동중인 원자력발전소 벽식 건물의 전단벽에 관통부를 신설할 경우에 발생하는 철근 절단의 영향을 평가하기 위하여 다양한 비선형 해석과 정적 가력 실험을 수행하였다. 그리고 관통부 신설과 철근의 절단으로 인한 벽체의 강성저하와 관통부 주변 철근의 응력 및 변형률 분포를 평가하였다.
In this study, first, transformation process of damping ratios, whose are evaluated in active control analysis, into damping matrix resulting from installed viscous dampers is illustrated. Then, a method is followed to maximize the effect of response reduction, which leads to optimum locations and size of viscous dampers using sensitivity analysis. Highly coupled nonlinearity between damping ratios and dampers makes it hard to find the optimal size of dampers. Therefore, the nonlinearity is transformed to linear problem with small increments of damping ratios and the size of dampers can be found. However, there are many cases for the size of dampers satisfying the small increment of damping ratios, so it is necessary to select minimum size using optimization technique. To determine optimum locations of dampers, dampers are assumed to be installed between the different stories and their locations are selected corresponding corresponding to the degree of damping size. Numerical examples for the frame structure and the shear wall structure show that optimum locations and size of dampers are different form each other depending on the characteristics of modal responses of the structures. The proposed method in this study can be applied to get optimum locations of active controller in the active control.
유체-고체 상호작용을 고려하여 다양한 복부대동맥류 모델에 대해서 맥동유동 및 구조를 동시에 해석하였다. 동맥류의 확장부 크기와 혈관벽 두께에 따라서 총 여덟 개의 축대칭 동맥류 모델을 선정하였다. 유한체적법 및 압력기반의 유한차분법을 이용하여 유동을 해석하였으며, 유한요소법을 이용하여 구조해석을 수행하였다. 동맥류의 확장부위가 클수록 최대응력은 최대확장부위와 변곡점에 해당하는 동맥류의 입구 및 출구 부분에 집중되었으며, Von Mises 응력은 최대확장부위 뿐만 아니라 동맥류의 근위부와 원위부($\pm$1D)에서도 현저하게 증가하였다. 또한 더욱 확장된 모델일수록 혈관벽은 직경방향의 변위보다 축방향의 변위가 지배적이었으며, 동맥류 원위부보다 근위부에서 큰 축방향 변위를 나타냈다. 동맥류 입구부의 미약한 와류는 한 주기동안 그 크기와 강도를 더해가며 동맥류 원외부로 이동하였고, 동맥류의 내부 유동은 압력차이가 감소하는 기간동안 더 큰 영향을 받았다. 확장정도가 심할수록 동맥류 내부에 더 크고 강한 와류가 관찰되었다. 압력차이가 최소가 된 직후 동맥류의 근위부와 원위부동맥 벽 근처에서의 역방향 유동이 관찰되었다. 대체로 혈관벽 두께가 감소한 모델과 더욱 확장된 모델일수록 벽전달률은 감소하였다. 혈관벽의 탄성에 의하여 압력차이와 벽전달률 사이에 위상차가 존재함이 확인되었다. 유체-고체의 상호작용을 고려한 연구는 다른 심혈관계를 이해하는데도 매우 유익할 것으로 생각된다.
암반 절리면과 같이 입자와 연속체 평면의 접촉면에서의 전단거동은 전체 구조물의 거동을 지배할 수 있다. 암반설계의 효율을 높이기 위해서는 입자와 연속체 평면의 접촉면 전단거동 메커니즘에 대한 기초적인 이해와 접촉면 전단강도를 정확하게 산정하는 것이 필수적이다. 본 연구에서는 연속체 평면의 표면 파쇄가 미치는 영향을 알아보기 위하여 개별요소법 수치해석 프로그램인 $PFC^{2D}$를 사용하였다. 표면 거칠기는 매끄러운 평면, 중간 거칠기 평면, 거친 평면의 세 가지로 구분하였다. 입자의 형상은 원형의 one ball 모델과 삼각형 형상의 3 ball 모델로 구성하였다. 평면은 파쇄가 불가능한 경계요소 연속체 모델과 파쇄가 가능한 입자요소 연속체 모델로 각각 구성하였다. 수치해석 결과, 입자요소 모델의 결합강도가 작을수록 파쇄가 빨리 발생하여 큰 결합강도를 가진 연속체 모델보다 작은 접촉면 전단강도를 보였다. 돌출부의 파쇄가 발생한 후, 접촉면 전단강도는 수렴하는 경향을 보이며, 결합강도가 클수록 돌출부의 파쇄가 적게 발생하였다. 또한 경계요소 연속체 모델이 입자요소 연속체 모델보다 큰 접촉면 마찰각을 나타냈고, 모든 입자 모델에서 연속체의 표면 거칠기가 거칠수록 큰 접촉면 마찰각이 나타났다. 이러한 결과로부터 연속체 평면의 거칠기 및 평면 파쇄가 입자와 평면의 접촉면 전단거동 특성에 미치는 영향을 확인하였다.
다양한 지반조건을 갖고 있는 지반구조물들은 공사 설계에 대한 특성에 따라 안정성 해석을 하여 설계와 시공이 되어야 한다. 일반적으로 지반의 강도정수들은 삼축압축시험으로 분석한 결과를 설계시공에 적용하여 안정성을 해석한다. 띠하중과 같은 응력을 받고 있는 댐, 제방, 옹벽 등은 한방향의 변형이 구속되어 있는 평면변형 조건의 지반구조물들이다. 지반 조건에 맞는 안정성 해석은 적절한 강도정수들의 적용에 의해서 이루어져야 한다. 삼축압축시험에 의한 강도정수 적용은 이러한 지반구조물들을 설계할 때, 안전율이 과소평가되어 시공성과 경제성에 불리하게 작용한다. 본 연구는 화강풍화토를 대상으로 삼축압축시험과 평면변형시험을 통하여 강도정수를 산정하고 상대밀도에 따른 강도 증가에 대한 경향을 분석하고자 한다. 삼축압축시험은 응력경화가 지속적으로 발생하기 때문에 최대 변형률 15%에서 한계파괴응력을 결정짓는 반면에, 평면변형 조건에서 수행되는 시험은 강도가 증가하면서 2번의 뚜렷한 응력경화를 나타내었고, 강도정수를 결정할 수 있는 항복응력을 구분할 수 있었다.
초고층 건축물의 RC 코아벽체 선행공법에서는 일반적으로 벽체와 철골보사이의 접합을 위해 강판을 벽체에 매입설치한다. 코어벽체에 설치한 매입강판에 철골보를 접합하기 위해서는 거셋플레이트(또는 단일판)을 사용하여 매입강판에 T-형으로 용접한다. 이에 용접입열에 의해서 매입강판은 열팽창과 용접변형이 발생하고 매입강판 주변 콘크리트 온도상승을 주어 구조적 안정성 평가가 필요하다. 이에, 본 연구에서는 매입강판과 거셋플레이트 사이의 용접자세(수평 및 수직자세), 콘크리트 타설후 용접시점 및 매입강판의 연단거리에 따른 매입강판 배면온도를 계측 하였다. 또한, 비정상 온도해석을 통하여 실험결과와 비교하였다. 다음으로 매입강판에 스터드앵커 접합한 후, Push-out 실험을 통한 구조성능을 조사하였다. 전단실험 결과 매입강판 용접열영향에 대해서 용접에 따른 최대하중은 14~19% 이내로 감소하였으며, 콘크리트 타설 후 용접시점에 따른 영향으로 타설 후 재령이 길수록 최대하중은 상승함을 알 수 있었다.
본 연구에서는 WFD(Wall Friction Damper)를 보강한 철근콘크리트 골조의 내진성능을 확인하기 위해 2층 철근콘크리트 골조 의 보강방법(무보강, 내부 H- 형철골과 WFD보강)을 주요 변수로 하였다. WFD 내진 보강 공법은 강도 향상과 에너지 소산 공법을 혼합한 것이다. WFD의 충분한 에너지 소산 이전에 보강재와 기존 구조물의 접합부에서 사전 파괴를 방지하기 위해 내부 H형 철골과 보 측면을 관통하는 케미컬 앵커를 사용하여 WFD를 설치하였다. 시험결과 OMF-N 시험체는 최대강도 발현 후 R/C 기둥의 전단력에 의한 취성파괴 양상을 보였다. OMF-ALL(H) 실험체는 핀칭 효과의 감소와 RC 기둥의 파손이 발생함을 보였다. 또한 OMF-ALL(H)의 최대 강도, 누적 에너지 소산 및 연성은 OMF-N의 경우 3.01배, 7.2배 및 1.72배 증가하였다. 그 결과 철근콘크리트 구조물에 시공한 WFD 내진 보강공법이 내진성능을 향상시키고 보강효과가 유효한 것으로 나타났다.
동적 하중 재하시 지반-구조물 상호작용 확인을 위해 진동대 실험이 많이 시행됐으나, 대부분 단자유도 상부 구조물과 단말뚝을 적용한 진동대 실험이 주를 이루고 있다. 이에 본 연구에서는 다자유도 구조물과 군말뚝을 적용한 대형진동대 실험을 통해, 상부 구조물의 관성 상호작용 영향을 분석하였다. 실험 결과, 단일 진동수에서의 증폭 경향을 나타내는 단자유도 구조물과는 다르게 다자유도 구조물에서는 다수의 진동수 구간에서 시간-가속도 발생 경향 및 응답 주파수의 유사성과 증폭 경향이 나타났다. 또한, 벽체 구조물에 비하여 기둥 구조물에서의 기초판과 상부 구조물과의 증폭현상이 더 크게 발생하여 기둥 구조물에 의한 관성 상호작용 효과가 더 큰 것으로 판단된다. 그리고 기초판에서의 전단력 및 관성력 관계, 상대 수직 변위 및 상대 수평 변위 관계와 심도별 동적 p-y 곡선에 대한 분석을 수행하였다. 분석 결과, 다자유도 구조물에서는 단자유도 구조물과는 상이한 거동을 나타내고 있으며, 벽체보다 기둥 구조물의 관성 상호작용의 효과가 더 큰 것으로 나타났다.
With the wide application of urban subway tunnels, the foundation pits of new stations and existing subway tunnels are becoming increasingly close, and even zero-distance close-fitting construction has taken place. To optimize the construction support scheme, the existing tunnel's vertical displacement is theoretically analyzed using the two-stage analysis method to understand the action mechanism of the construction of zero-distance deep large foundation pits on both sides of the existing stations; a three-dimensional numerical calculation is also performed for further analysis. First, the additional stress field on the existing tunnel caused by the unloading of zero-distance foundation pits on both sides of the tunnel is derived based on the Mindlin stress solution of a semi-infinite elastic body under internal load. Then, considering the existing subway tunnel's joints, shear stiffness, and shear soil deformation effect, the tunnel is regarded as a Timoshenko beam placed on the Kerr foundation; a sixth-order differential control equation of the tunnel under the action of additional stress is subsequently established for solving the vertical displacement of the tunnel. These theoretical calculation results are then compared with the numerical simulation results and monitoring data. Finally, an optimized foundation pit support scheme is obtained considering the pit corner effect and external corner failure mode. The research shows a high consistency between the monitoring data,analytical and numerical solution, and the closer the tunnel is to the foundation pit, the more uplift deformation will occur. The internal corner of the foundation pit can restrain the deformation of the tunnel and the retaining structure, while the external corner can cause local stress concentration on the diaphragm wall. The proposed optimization scheme can effectively reduce construction costs while meeting the safety requirements of foundation pit support structures.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.