• Journal of the Korean GEO-environmental Society
• /
• v.11 no.12
• /
• pp.57-62
• /
• 2010

In this study, the effect of different silt contents on the shear characteristics of silty sands was evaluated. Two series of triaxial compression tests were performed on the cylindrical specimens of compacted Nakdong river sand with 10% and 30% silt contents under unconsolidated undrained condition. All identical specimens were prepared to compact with same initial water content for five layers and saturated using control panel and then sheared under initial effective confining pressure, 100 to 400kPa. All specimens exhibited a strain softening tendency after failure in stress-strain curves and deviator stresses of specimens with 10% silt content were greater than those of specimens with 30% silt content. Pore water pressures of specimens with 10% silt content were observed negative(i.e. swelling) due to increasing void ratio after failure but those of specimens with 30% silt content were shown only positive. The behavior of compacted cylindrical specimens with low silt content was more dilative than that of high silt content. Peak deviator stresses decreased as increasing silt content and peak pore water pressures increased as increasing silt content.

• Bulletin of the Korean Chemical Society
• /
• v.2 no.3
• /
• pp.96-104
• /
• 1981

(1) The flow data of f (stress) and ${\dot{s}$ (strain rate) for Fe and Ti alloys were plotted in the form of f vs. -ln ${\dot{s}$ by using the literature values. (2) The plot showed two distinct patterns A and B; Pattern A is a straight line with a negative slope, and Pattern B is a curve of concave upward. (3) According to Kim and Ree's generalized theory of plastic deformation, pattern A & B belong to Case 1 and 2, respectively; in Case 1, only one kind of flow units acts in the deformation, and in Case 2, two kinds flow units act, and stress is expressed by $f={X_1f_1}+{X_2f_2}$where $f_1\;and\;f_2$ are the stresses acting on the flow units of kind 1 and 2, respectively, and $X_1,\;X_2$ are the fractions of the surface area occupied by the two kinds of flow units; $f_j=(1/{\alpha}_j) sinh^{-1}\;{\beta}_j{{\dot{s}}\;(j=1\;or\;2)$, where $1/{\alpha}_j\;and\;{\beta}_j$ are proportional to the shear modulus and relaxation time, respectively. (4) We found that grain-boundary flow units only act in the deformation of Fe and Ti alloys whereas dislocation flow units do not show any appreciable contribution. (5) The deformations of Fe and Ti alloys belong generally to pattern A (Case 1) and B (Case 2), respectively. (6) By applying the equations, f=$(1/{\alpha}_{g1}) sinh^-1({\beta}_{g1}{\dot{s}}$) and $f=(X_{g1}/{\alpha}_{g1})sinh^{-1}({\beta}_{g1}{\dot{s}})+ (X_{g2}/{\alpha}_{g2})\;shih^{-1}({\beta}_{g2}{\dot{s}})$ to the flow data of Fe and Ti alloys, the parametric values of $x_{gj}/{\alpha}_{gj}\;and\;{\beta}_{gs}(j=1\;or\;2)$ were determined, here the subscript g signifies a grain-boundary flow unit. (7) From the values of ($({\beta}_gj)^{-1}$) at different temperatures, the activation enthalpy ${\Delta}H_{gj}^{\neq}$ of deformation due to flow unit gj was determined, ($({\beta}_gj)^{-1}$) being proportional to , the jumping frequency (the rate constant) of flow unit gj. The ${\Delta}H_{gj}\;^{\neq}$ agreed very well with ${\Delta}H_{gj}\;^{\neq}$ (self-diff) of the element j whose diffusion in the sample is a critical step for the deformation as proposed by Kim-Ree's theory (Refer to Tables 3 and 4). (8) The fact, ${\Delta}H_{gj}\;^{\neq}={\Delta}H_{j}\;^{\neq}$ (self-diff), justifies the Kim-Ree theory and their method for determining activation enthalpies for deformation. (9) A linear relation between ${\beta}^{-1}$ and carbon content [C] in hot-rolled steel was observed, i.e., In ${\beta}^{-1}$ = -50.2 [C] - 40.3. This equation explains very well the experimental facts observed with regard to the deformation of hot-rolled steel..

• Composites Research
• /
• v.32 no.1
• /
• pp.37-44
• /
• 2019

The reinforcement effect of micro-bolt for a bonded scarf joint was investigated. Three scarf ratios of 1/10, 1/20, and 1/30 were considered to examine the effect of scarf patch configuration on joint strength. To maintain the same density of micro-bolt, 16, 32, and 48 bolts were installed in the scarf joint specimens with scarf ratios of 1/10, 1/20, and 1/30, respectively. Tests were also carried out on the joints that are bonded with only adhesive and that are fastened with only micro-bolts to obtain reference values. The average failure loads of the adhesive joints with scarf ratios of 1/10, 1/20, and 1/30 were 29.7, 39.6, and 44.8 kN, respectively. In case of micro-bolt reinforcement, the failure loads at the same scarf ratios were 28.4, 37.2, and 40.1 kN, respectively, which corresponds to 96, 94, and 90% of the pure adhesive joint failure loads. In the case of using only micro-bolts, the failure loads were only 13-25% of the average failure loads of pure adhesive joints. Fatigue test was also conducted for the joints with scarf ratio of 1/10. The results show that the fatigue strength of hybrid joints using both adhesive and microbolts together slightly increased compared to the fatigue strength of adhesive joint, but the rate of increase was small to 2-3%. Through this study, it was confirmed that the reinforcement effect of micro-bolt is negligible in the scarf joints where shear stress is dominating the failure, unlike in the structure where peel stress is dominant.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.2
• /
• pp.73-82
• /
• 2022

The study presents a three-dimensional approach to simulate the nonlinear behavior of a 72 m long Ultra High Performance Fiber Reinforced Concrete (UHPFRC) pre-stressed box girder for a pedestrian bridge in Busan, South Korea. The concrete damage plasticity (CDP) model is adopted to model the non-linear behavior of the UHPFRC material, in which the material properties are obtained from uniaxial compressive and tensile tests. The simulation model based on the proposed stress-strain curve is validated by the results of four-point bending model tests of a 50 m UHPFRC pre-stressed box girder. The results from the simulation models agree with the experimental observations and predict the flexural behavior of the 50 m UHPFRC pre-stressed box girder accurately. Afterward, the validated model is utilized to investigate the flexural behavior of the 72 m UHPFRC pre-stressed box girder. Here, the load-deflection curve, stress status of the girder at various load levels, and connection details is analyzed. The load-deflection curve is also compared with design load to demonstrate the great benefit of the slender UHPFRC box girder. The obtained results demonstrate the applicability of the nonlinear finite element method as an appropriate option to analyze the flexural behavior of pre-stressed long-span girders.

• Food Science of Animal Resources
• /
• v.42 no.1
• /
• pp.128-141
• /
• 2022

Compared to the conventional farms (CF) rearing of broilers, the rearing management of animal welfare-certified farms (AF) must provide low stocking density, perch, air regulation, and feeding plant-based protein. This study aimed to compare the effects of rearing management in CF and AF on blood parameters, meat quality, and bioactive compound content in Ross 308 broiler chickens at the farm level before transportation to slaughterhouses. Blood and meat samples were obtained at 28-35-dayold chickens from three CF and three AF. In blood samples, low-density lipoprotein cholesterol (p<0.05), triglyceride (p<0.001), glucose (p<0.01), total protein (p<0.001), albumin (p<0.01), and white blood cell (p<0.001) levels as well as the heterophil/ lymphocyte ratio [stress index (SI), p<0.001] were lower in broilers from AF than in CF. In meat samples, shear force (p<0.001, p<0.05), and carnosine contents (p<0.001, p<0.05) in both breast and thigh meat from AF were higher than those in meat from CF. The contents of linoleic acid (p<0.001), α-linolenic acid (p<0.001), and eicosapentaenoic acid (p<0.05) were higher in the samples from AF than those from CF. This study reveals that such differences are influenced by the different rearing factors in nutrition, housing, and management practices between CF and AF. Supplementation of plant-based protein and enough space to move due to lower stocking density accounts for the large differences between them. These results can be used as preliminary data showing that the AF system reduces the SI and enhances carnosine and polyunsaturated fatty acids levels in chicken meat at the farm level before transportation.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.1
• /
• pp.35-44
• /
• 2006

In general typically granular soils contain a certain amount of fines. It is also widely recognized that foundation soils under working loads show highly non-linear behavior from very early stages of loading. In the present study, a series of laboratory tests with sands of different silt contents are conducted and methods to assess strength and stiffiness characteristics are proposed. Modified hyperbolic stress-strain model is used to analyze non-linearity of silty sands in terms of non-linear Degradation parameters f and g as a function of silt contents and Relative density Dr. Stress-strain curves were obtained from a series of triaxial tests on sands containing different amounts of silt. Initial shear modulus, which is used to normalize Degradation modulus of silty sands, was determined from resonant column test results. From the laboratory test results, it was observed that, as the Relative density increases, values of f decrease and those of g increase. In addition, it was found that values of f and g increase and decrease respectively as a Skeleton void ratio $(e_{sk})$ increases.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.12
• /
• pp.75-82
• /
• 2007

The effects of sitting pressure(${\sigma_{sit}}'$) during cementation, relative density and particle characteristics on the cohesion intercept due to cementation bonds and the confining stress inducing the breakage of cementation bonds ${p_i}'_{(BP)}$ are investigated from drained shear tests on the cemented sands confined under the isotropic stress up to 400 kPa. It was observed from the experimental results that the cemented sands, with the same density and gypsum content, show similar values of cohesion intercept and ${p_i}'_{(BP)}$, regardless of ${\sigma_{sit}}'$. Although the cohesion intercept and ${p_i}'_{(BP)}$ of cemented sands are observed to increase with increasing relative density and cementation level, the relative density appears to have more significant effect on ${p_i}'_{(BP)}$ than the cohesion intercept does. From analysing the test results of three different sands, it is shown that the smaller the particle size the larger the cohesion intercept and ${p_i}'_{(BP)}$, due to the increased number of contact points between the particles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.2C
• /
• pp.71-79
• /
• 2009

This study is to develope the resilient modulus prediction model, which is the function of mean effective principal stress and axial strain, for three types of railroad trackbed materials such as crushed stone, weathered granite soil, and crushed-rock soil mixture. The model consists of the maximum Young's modulus and nonlinear values for higher strain, analogous to dynamic shear modulus. The maximum value is modeled by model parameters, $A_E$ and the power of mean effective principal stress, $n_E$. The nonlinear portion is represented by modified hyperbolic model, with the model parameters of reference strain, ${\varepsilon}_r$ and curvature coefficient, a. To assess the performance of the prediction models proposed herein, the elastic response of a test trackbed near PyeongTaek, Korea, was evaluated using a 3-D elastic multilayer computer program (GEOTRACK). The results were compared with measured elastic vertical displacement during the passages of freight and passenger trains at two locations, whose sub-ballasts were crushed stone and weathered granite soil, respectively. The calculated vertical displacements of the sub-ballasts are within the order of 0.6mm, and agree well with measured values. The prediction models are thus concluded to work properly in the preliminary investigation.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.2
• /
• pp.97-107
• /
• 2003

To obtain a more accurate response from larninated composite structures, the effect of transverse shear deformation, transverse normal strain/stress, and nonlinear variation of in-plane displacements vis-$\\grave{a}$-vis the thickness coordinate should be considered in the analysis. The improved higher-order theory was used to determine the critical buckling load and natural frequencies of laminated composite structures. Solutions of simply supported laminated composite plates and sandwiches were obtained in closed form using Navier's technique, with the results compared with calculated results using the first order and other higher-order theories. Numerical results were presented for fiber-reinforced laminates, which show the effects of ply orientation, number of layers, side-toithickness ratio, and aspects ratio.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.115-126
• /
• 1996

The purpose of 1,his study is to analyze the compression and strength charactefistics of the decomposed -weathered soil originating from biotite gneiss or fine grained gneiss sampled from Poidong, Seoul : to figure out the behavioural characteristics of the decomposed -weathered soil in accordance with mineral composition and origin by comparing experimental results of residual soils. originating from granites and sampled from Bulam, Andong and Kimchun area. A series of CIU, CID CKoV, CKoD tests were car lied out. Although weathered soils have different origin and mineral composition, the slope of the NCL A was similar. It was also shown that plastic strain ratio was about 85% mainly due to the particle crushing effect during compression. The Poidong soil showed strain softening phenomenon unlike the Kimchun and Andong soils. this implies that the behavioural characteristics are affected by the origin and the mineral composition of the soil particles. Moreover, it was found that the angle of the shear resistance$(\phi')$ was dependent on the mineral composition. On the oher hand, measured Af values of decomposed weathered soils were more than one regardless of the origin and the mineral composition.