• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.145-153
• /
• 1991

A numerical simulation of the nonsteady state rolling process in the plane strain condition is presented in the basis of the rigid-plastic finite element method by considering large deformation. In order to apply the large deformation theory to the numerical method for sheet rolling problems, constitutive equation relating 2nd-Piola Kirchhoff stress and Lagrangian strain which reflect geometrical nonlinearity is used. To confirm the validity of the developed algorithm, the analysis of the neutral flow region, roll separating force, torque, pressure and stress/strain distributions on the workpiece is conducted from the bite of the material until the steady state is reached. The computed results of the roll force and torque in the present finite element analysis are lower than those corresponding to small strain theory. The pressure distribution at the work piece-roll interface is found to show the typical 'friction hill' type only. The peak value in near the neutral region, however, is good agrements with the existing results. the neutral region, however, is good agrements with the existing results. The frictional force at the roll interface provide detailed information about the neutral point where the shear forces change direction. In addition, the analysis also includes the effect and influence of material condition, strip thickness, work roll diameter, as well as roll speed and lubricant on each deformation process.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.718-725
• /
• 2002

A wall type friction damper is newly Proposed in this paper to improve the performance of R/C framed structures under earthquake loads. Although traditional dampers are usually placed as bracing members, the application ot bracing-type dampers into R/C structures is not as simple as those of steel structures due to the connection between R/C members and dampers and the stress concentration in connection region. Proposed damper is consisted of Teflon-sheet slider and R/C shear wall. The damper can also avoid stress concentration and reduce P-Δ effect. To evaluate the performance of proposed damper, nonlinear dynamic analyses are carried on 10 story and 3 bay R/C structures with numerical model for the damper. It is shown that the damper reduces the inter-story drifts and the time-historic responses; especially the damper prevents from forming plastic hinges on the lower columns.

• Fashion & Textile Research Journal
• /
• v.17 no.4
• /
• pp.613-625
• /
• 2015

This research was conducted to provide basic data to improve expressivity required for virtual clothing to replace actual clothing. For the experiment, 6 materials were selected and 12(2 kinds of length) actual flared skirts were made. At the same time, simulations were carried out on OptiTex Runway 12.0 for 36(12 kinds of skirts $\times$ KES, FTU, KES weight/10) kinds of virtual flared skirts, which were applied with the measured property values (thickness, weight, bending, shear, friction, and stretch). Also, the study compared and analyzed the wearing images, silhouette overlapping images, and skirt length measurements of the actual and virtual skirts put on a dummy. As a result, the actual skirts showed clear distinction for each material. In contrast, virtual 1 and 2 expressed fabric 3 in the most similar way, but could not recreate the uniform, soft, and natural flare shape of the actual skirts in general. Virtual 3 formed natural flares as those of the actual skirts, and expressed fabric 1, 5, and 6 in a similar way. However, virtual 3 had too much volume and barely showed any distinction for each material. All of virtual 1, 2, and 3 expressed different flare shapes on the front and back sides of the skirt similarly to the actual skirts, and had a good visual expression for the color and texture of the materials. However, they could not effectively express the elasticity and fabric sagging in the bias direction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.11
• /
• pp.1055-1063
• /
• 2012

Fluctuating wall pressures were measured using an array of 16 piezoelectric transducers beneath a turbulent boundary layer. The coating used in this experiment was an open-cell, urethane-type foam with a porosity of approximately 50 ppi. The ultimate objective of the coating is to provide a mechanical filter to reduce the wall pressure fluctuations. The boundary layer on the flat plate was measured by using a hot wire probe, and the CPM method was used to determine the skin friction coefficient. The wall pressure autospectra and streamwise wavenumber-frequency spectra were compared to assess the attenuation of the wall pressure field by the coating. The coating is shown to attenuate the convective wall pressure energy. However, the relatively rough surface of the coating in this investigation resulted in a higher mean wall shear stress, thicker boundary layer, and higher low-frequency wall pressure spectral levels compared to a smooth wall.

• The Journal of Engineering Geology
• /
• v.27 no.1
• /
• pp.31-40
• /
• 2017

The slope stability analysis by the limit equilibrium method has the disadvantage that it can be applied only when the analysis is performed by setting the critical plane after analyzing the active surface many times and the soil is uniform and only the safety factor can be calculated. However, the analysis using the strength reduction analysis method has advantages that the engineer can judge various aspects and calculate the safety factor. In this study, the safety factor according to the change of slope and shear strength was compared and analyzed using limit equilibrium analysis and strength reduction method. It is suggested that it is desirable to use the strength reduction method which can synthetically review the stress, displacement, and strain in the soil.

• Tribology and Lubricants
• /
• v.36 no.3
• /
• pp.168-192
• /
• 2020

In recently designed diesel engines, the running conditions for piston-pin bearings have become severe because of the higher combustion pressure and increased temperature. Moreover, the metal removal from the bushing material has strongly reduced the ability of the antifriction material to accept asperity contacts. Therefore, it is necessary to find ways of reducing wear scar on the connecting-rod small-end bushing and piston-pin boss bearing related to the higher combustion pressure on the power cell of an engine. In this work, the position and level of material removal from the surfaces of the bushing and bearing under such severe operating conditions - for example, maximum power and torque conditions of a passenger car diesel engine - are estimated for several combinations of surface roughness. First, piston-pin rotating motion is investigated by calculating the friction coefficient at piston-pin bearings, the oil film thickness, and the frictional torques induced by hydrodynamic shear stress. Subsequently, the wear scarring on the surfaces of a connecting-rod small-end bushing and two piston-pin boss bearings related to piston-pin rotational motion is numerically calculated under the maximum power and torque operating conditions. This work is helpful to determine the reasonable surface roughness of the bushing and bearing for reducing wear volume occurring at the interface between a bearing and a shaft.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1122-1129
• /
• 2010

Various soil tests were performed in the laboratory after soil samples were obtained from natural terrains distributed on the granitic rocks where are located in Mt. Bukhan, Mt. Surak and Mt. Gwanak around Seoul. Through the comparison of soil properties in each mountain, the difference of soil properties in a similar geological condition was investigated. According to the result of soil test, the soils were generally classified into calyey and silty sands with a well grade. Soil densities are ranged from $2.62kg/cm^3$ to $2.67kg/cm^3$, and water contents of soils are ranged from 3.77% to 31.12%. These values are not sorted locally. The wet unit weights of soils are ranged from $1.092kg/cm^3$ to $1.814kg/cm^3$. It has a big difference between the average values because that of Mt. Bukhan is $1.604kg/cm^3$ and those of Mt. Surak and Mt. Gwanak are $1.500kg/cm^3$ and $1.331kg/cm^3$, respectively. The internal friction angles are ranged from $31^{\circ}$ to $39^{\circ}$ and the cohesions are ranged from 1.57kPa to 8.63kPa. The shear strengths are too high and similar in all regions. The coefficients of permeability are ranged from $3.07{\times}10^{-3}cm/sec$ to $4.61{\times}10^{-2}cm/sec$. So, these soils are evaluated as a middle to high permeable ground. On average, the value of Mt. Bukhan is $1.47{\times}10^{-2}cm/sec$ and the values of Mt. Surak and Mt. Kwanak are $1.29{\times}10^{-2}cm/sec$ and $1.66{\times}10^{-2}cm/sec$, respectively.

• Journal of Environmental Science International
• /
• v.1 no.2
• /
• pp.105.2-117
• /
• 1992

The formation mechanism of the vortex streets in the lee of the mountain Is Investigated by a three-dimensional numerical model. The model is based upon the hydrostatic Boussinesq equations in which the vertical turbulent momentum flux is estimated by a turbulence parameterization scheme, but the horizontal viscosity is assumed to be constant. The results show that Karman vortex streets can form even without surface friction in a constant ambient flow with uniform stratification. The vortex formation is related to breaking of the mountain wave, which depends on the Froude number (Fr). In the case of a three-dimensional bell-shaped mountain, the wave breaking occurs when Fr is less than about 0.8, while a barman vortex forms when Fr is less than about 0.22. Vortex formation also depends on Reynolds number, which is estimated from the horizontal diffusivity. The vortex formation can be explained by the wave saturation theory given by Lindzen (1981) with some modification. Simulations in this study show that in the case of Karman vortex formation the momentum flux in the lower level is much larger than the saturated momentum flux, whereas it is almost equal to the saturated momentum at the upper levels as expected from the saturation theory. As a result, large flux divergence is produced in the lower layer, the mean flow is decelerated behind the mountain, and the horizontal wind shear forms between unmodified ambient wind. The momentum exchange between the mean flow and the mountain wave is produced by the turbulence within a breaking wave. From the result, well developed vortices like Karman vortex can be formed. . The results of the momentum budget calculated by the hydrostatic model are almost the same as nonhydrostatic results as long as horizontal scale of the mountain is 10 km. A well developed barman vortex similar to the hydrostatic one was simulated in the nonhydrostatic case. Therefore, we conclude that the hydrostatic assumption is adequate to investigate the origin of the Km8n vortex from the viewpoint of wave breaking.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.72-80
• /
• 2018

With the ever increasing advances in computers and their computing power, computational fluid dynamics(CFD) has become an essential engineering tool in the design and analysis of engineering applications. Accordingly, many universities have developed and implemented a course on CFD for undergraduate students. On the other hand, many professors have used industrial examples supplied by computational analysis software companies as CFD examples. This makes many students think of CFD as difficult and confusing. This paper presents a simple CFD example used in the department of mechanical design engineering of Kangwon National University and shows its effectiveness. Most students answered that a simple CFD example is more comprehensive than an industrial example. Therefore, it is necessary to develop simple computational analysis problems in the engineering education field.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.1
• /
• pp.89-98
• /
• 2017

The offshore plant structure has been transported to the site by barge because it is hard to manufacture in site. When the structure was transported on the sea, offshore plant structures and connection were experienced repetitive submarine load. For this reason, it was known for that the axial force of high-strength bolted connection was declined. Therefore, in this study, high-strength bolted connection was evaluated the shear fatigue performance under longtime fatigue load during marine transport. The experimental variables were selected intial axial force, surface type, and bolt type because they ar important factors in the change of axial force of bolts. As a experimental results of considering various variables, the variation of axial force showed within 1%. Therefore, the high-strength bolted connection was verified structural safety under longtime fatigue load.