• Geomechanics and Engineering
• /
• 제3권2호
• /
• pp.153-167
• /
• 2011

Traditional design methods of bearing capacity of shallow foundations are deterministic in the sense that they do not explicitly consider the inherent uncertainty associated with the factors affecting bearing capacity. To account for such uncertainty, available deterministic methods rather employ a fixed global factor of safety that may lead to inappropriate bearing capacity predictions. An alternative stochastic approach is essential to provide a more rational estimation of bearing capacity. In this paper, the likely distribution of predicted bearing capacity of strip footings subjected to vertical loads is obtained using a stochastic approach based on the Monte Carlo simulation. The approach accounts for the uncertainty associated with the soil shear strength parameters: cohesion, c, and friction angle, ${\phi}$, and the cross correlation between c and ${\phi}$. A set of stochastic design charts that assure target reliability levels of 90% and 95%, are developed for routine use by practitioners. The charts negate the need for a factor of safety and provide a more reliable indication of what the actual bearing capacity might be.

• 설비공학논문집
• /
• 제13권12호
• /
• pp.1275-1281
• /
• 2001

Aqueous polymer solutions are known to have small pressure reduction. Paraffin slurries are known to have high thermal capacity. Paraffin particles are mixed into an aqueous polymer solution to make a new heat transfer fluid having high thermal capacity but low pressure reduction. The heat transfer characteristics of the new slurry was tested in a circular tube having a constant heat transfer boundary condition. The new slurry was found to have high Nusselt numbers as well as high thermal capacity and low pressure reduction in the laminar flow. The trends of the Nusselt numbers along the heating test section were studied for various heating conditions.

• 수산해양교육연구
• /
• 제5권2호
• /
• pp.128-137
• /
• 1993

This paper presents a new concept to reduce turbulent frictional drag by injecting micro-bubble into buffer layer of turbulent boundary layer on flat plate. The buffer layer of boundary was specified by minus velocity gradient of law of the wall. When the buffer layer region of turbulent boundary layer is filled with micro-bubble of air and viscous of the region is kept low, the velocity profile in the region should be changed substantially. Then the Reynolds stress in the buffer layer region becomes less, which guide to higher velocity gradient there. It results in reduction of velocity gradient at the viscous sublayer, which gives the reduction of shear stress at the wall.

• 한국농공학회논문집
• /
• 제47권1호
• /
• pp.43-50
• /
• 2005

This test was performed to evaluate the change of the unconfined compressive strength, strength parame¡?ters which resulted from direct shear test and oil residue percents analyzed by GC-MS as time lapse, oil addition. Unconfined compression strength of $10\%$ kerosene added by weight of dry soil recovered as time passed. In the case of $5\%$ kerosene added, the strength recovered as much as clean clayey soil after about 50 days passing. For the case of diesel added, the recovery of unconfined compressive strength was not shown even though about 60 days passed. The strength parameters (c, $\psi$) of kerosene added not changed but for diesel added, the cohesion was very decreased as diesel addition increased. Residual percent of kerosene in the soil was less than that of diesel as time passed.

• 한국안전학회지
• /
• 제11권4호
• /
• pp.90-96
• /
• 1996

This paper examines the De-inking characteristics of mechanical methods using the newly developed De-inking machine along with experiments to enhance the manufacture of recycled kraft pulp with the addition of newspaper. This study concluded that : First, the De-Inking ratio was affected by shear stress and friction resistance operating In the stainless steel net. Second, the brightness improvement ratio was raised by 6.2% under the following conditions : 120rpm rotor speed, 2.18% concentration, using two treatment cycles. Third, it was shown that the tearing strength was improved by about 10 to 20% , and the tensile strength remained the same when recycled kraft pulp was added with 20% wasted paper. In sum, by these experiments we have proven that the performance of the newly developed De-inking machine can be improved.

• 한국정밀공학회지
• /
• 제16권11호
• /
• pp.166-173
• /
• 1999

Al forged parts are many cases with rib-web section which is difficult to manufacture precisely. Therefore, process conditions must be optimized for precision forging of Al alloys. In this study, various process parameters such as die design, lubricant, ram speed, forging temperature have been investigated using the experiment, upper bound theory and F.E.M. simulation to develop the precision forging technology for rib-web shape component. When lubricant is applied to both material and die, shear friction factor is 0.1 which shows best effect of lubricant. It is specific corner radius of die that minimized forging load regarding process conditions, especially according to the ratio of the width of rib and web. In conclusion, optimum corner radius is 2~3mm when the width of rib and web is 3mm and 20mm respectively.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.138-144
• /
• 1997

The analysis of lateral hydrodynamic forces from the compressor labyrinth seals is presented. The basic equations are derived using a two-control-volume model for compressible flow. Blasius' wall friction-factor formula and jet flow theory are used for the calculation of the wall shear stresses and the recirculation velocity in the cavity. Linearized zeroth-order and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. Integration of the resultant first-order pressure distribution along and around the seal defines the rotordynamic coefficients of the labyrinth seal. The rotordynamic analysis for the balance drum labyrinth seal of an ethylene refrigeration compressor is carried out. The results of rotordynamic characteristic of the labyrinth seal and comparisons with other types of seal, honeycomb seal and smooth seal, are presented.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1999년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall
• /
• pp.236-243
• /
• 1999

A comparative study on aseismatic performances of various base isolation systems for the multi-span continuous bridge is carried out. Several leading base isolation systems the LRB system the RF system the R-FBI system and the EDF system are considered, The displacement of the deck the deformation of the upper ends of the piers the shear force and the bending moment of the lower ends of the piers are obtained by using the accelerograms of the N00W component of El Centro earthquake(1940) and the N90W component of Mexico City earthquake(1985) Nonlinear time-history analysis is carried out. comparisons of the results with the conventional bearing show that the base isolation systems are very effective in reducing the forces transmitted to the superstructures. Furthermore the results also show that the friction-type base isolation systems are less sensitive to unexpected variations in frequency content of the ground acceleration. The R-FBI system shows a good aseismatic performance comparing with other base isolation systems.

• 반도체디스플레이기술학회지
• /
• 제18권1호
• /
• pp.25-31
• /
• 2019

In this study, a new adhesion evaluating equipment and data processing methods were developed to overcome some limitations of existing evaluating equipment. Nano-diamond coated tool is a specimen of experiment. When applying frictional force and shear force on the specimen by a rotating polishing pad, delamination occurs at a moment. During each experiment, the vibration, load, and torque is obtained by accelerometer, loadcell and torque s+ kpensor. Frictional force and coefficient of friction are obtained by calculating torque and load. Based on FFT transformation, acceleration is processed and analyzed. As a result, the moment of delamination and the load at that time can be detected by the new developed equipment and measurement system. Finally, we call this load as an Adhesion force.

• 한국정밀공학회지
• /
• 제12권10호
• /
• pp.102-112
• /
• 1995

Temperature distribution on the rake face and flank face in orthogonal turning with cutting tool of high speed steel is studied by using a finite element method and experiments. Experiments are carried out to verify the validity of the temperature measurement by using a thermoelectric couple junction imbedded in a cutting tool of high speed steel. Good agreement is obtained between the analytical results and the experimental ones for the temperature distributions on both the rake face and flank face of cutting tool with high speed steel. The analytical results show that the temperature on the top flank face of a tool is higher than it on the top rake face of the tool because of the difference of the friction velocity on each face of the tool.