• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.319-324
• /
• 2016

Soils with various particle sizes generally show good shear strength. Some soils have a relatively strong resistance to shear failure in spite of narrow particle distribution, such as gap grading. Based on this example, it can be inferred that appropriate arrangements of particle size in soils might result in an increase in shear strength. This study investigates the strength variation of soils with respect to the particle size distribution. Gap, well, and uniform graded soils were prepared with a desired ratio, and a wide range of direct shear tests were done using the prepared samples. The test results show that there is a strong relationship between the particle size ratio and internal frictional angle. Gap graded soil has a greater frictional angle than a well-graded sample, even when specimens have the same maximum particle size, which is also the case for the uniform grade specimen. The results have potential for developing a methodology for stronger soils through a simple manipulation of particle size distribution.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.1
• /
• pp.153-166
• /
• 1991

In an attempt to investigate the effect of intermedate principal stresses which are related to the stress-strain behavior of standard sands, a series of three-Principal stress control tests were conducted for individual stress paths. The results have shown that shear strengths of sands vary with the stress paths. The variations in internal friction angle are accorded with the Habibs stress parameter, b which represents Stress paths, showing on abropt increase at the values between 0.0 and 0.268, a moderate level between 0.268 and 0.682, and a slight decrease between 0.682 and 1.0 However, the friction angles under a triaxial extention state, were found relatively larger than under a triaxial compression state. In general, such veriations were found to have the same tendency without any relevant relation with the density of specimens and confining pressures. Therefore, it is concluded, that the shear strength of sands are positively influeced by the intermediate principal stresses present in the media. And the influnce of intermediate principal stresses on shear strengths of sands found from the present study are well compared with the previous studies by Lade-Duncan and Matsuoka-Nakai revealing a similar tendency within the failure criteria proposed by them.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.4
• /
• pp.321-336
• /
• 2012

The shear behavior at the particle/surface interface such as rock joint can determine the mechanical behavior of whole structure. Therefore, a fundamental understanding of the mechanisms governing its behavior and accurately estimation of the interface strength is essential. In this paper, PFC, a numerical analysis program of discrete element method was used to investigate the effects of the surface roughness crushing on interface strength. The surface roughness was characterized by smooth, intermediate, and rough surface, respectively. Particle shape was classified into one ball model of circular shape and 3 ball model of triangular shape. The surface shape was modelled by wall model of non-crushing surface and ball model of crushing surface. The results showed that as the bonding strength of ball model decreases, lower interface strength is induced. After the surface roughness crushing was occurred, the interface strength tended to converge and higher bonding strength induced lower surface roughness crushing. Higher friction angle was induced in wall model and higher surface roughness induced the higher friction angle. From these findings, it is verified that the surface roughness and surface roughness crushing effect on the particle/surface interface shear behavior.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.2
• /
• pp.25-33
• /
• 2016

This study was a basic research to obtain the knowledge of physical properties of the upper sedimented sandy soil in the Nakdong river delta area. The characteristics of shear strength and permeability with fine content and relative density were also investigated. The upper sedimented sandy soil near paddy and lower soft clay layers showed high percentage of fine content, and the rest parts had about 5% of fine content. The specific gravity regardless of depth and location was almost constant. The upper sedimented sandy soil mostly had particle size about 0.1 ~ 0.4mm regardless of sedimentation environment and has illite, a clay mineral, in the entire soil samples. The results of direct shear tests on remolded specimens of the upper sedimented sandy soil revealed that the friction angle and cohesion increased with relative density, but its effect was not significant. The fine content was significant, that as increasing it, the friction angle decreased and cohesion increased linearly. The permeability decreased with relative density and fine content, and the permeability of soil containing more than 15% of fine content was independent on the relative density.

• Journal of Hydrogen and New Energy
• /
• v.25 no.5
• /
• pp.550-559
• /
• 2014

Hydraulic performance of the 1 inch ball valve have been analyzed based on the three-dimensional Reynolds-averaged Navier-Stokes analysis and an experiment. The experimental test rig of the 1 inch ball valve has been developed to investigate pressure drop for the 1 inch ball valve. The numerical model, which has reliability and effectiveness, has been constructed through the grid dependency test and validation with the results of the experiment. Shear stress transport turbulence model has been used to enhance an accuracy of the turbulence prediction in the pipeline and ball valve, respectively. Effects of the ball valve angle on the flow characteristics and friction performance have been evaluated.

• Geomechanics and Engineering
• /
• v.5 no.2
• /
• pp.119-142
• /
• 2013

Pile load tests using Osterberg cells (O-cell) were conducted on cast-in-place concrete piles founded in oil sand fill and in situ oil sand at an industrial plant site in Fort McMurray, Alberta, Canada. Interpreted pile test results show that very high pile shaft resistance (with the Bjerrum-Burland or Beta coefficient of 2.5-4.5) against oil sand could be mobilized at small relative displacements of 2-3% of shaft diameter. Finite element simulations based on linear elastic and elasto-plastic models for oil sand materials were used to analyze the pile load test measurements. Two constitutive models yield comparable top-down load versus pile head displacement curves, but very different behaviour in mobilization of pile shaft and end bearing resistances. The elasto-plastic model produces more consistent matching in both pile shaft and end bearing resistances whereas the linear elastic under- and over-predicts the shaft and end bearing resistances, respectively. The mobilization of high shaft resistance in oil sand under pile load is attributed to the very dense and interlocked structure of oil sand which results in high matrix stiffness, high friction angle, and high shear dilation.

• Steel and Composite Structures
• /
• v.15 no.3
• /
• pp.299-322
• /
• 2013

In the case of seismic-resistant composite dual moment resisting and eccentrically braced frames, the current design practice is to avoid the disposition of shear connectors in the expected plastic zones, and consequently to consider a symmetric moment or shear plastic hinges, which occur only in the steel beam or link. Even without connectors, the real behaviour of the hinge may be different from the symmetric assumption, since the reinforced concrete slab is connected to the steel element close to the hinge locations, and also due to contact friction between the concrete slab and the steel element. The paper presents the results and conclusions of experimental tests on composite portal eccentrically braced frames and beam-to-column moment-resisting joints, carried out within the CEMSIG Research Centre of the Politehnica University of Timisoara, in order to check the validity of the assumption stated above. Reference steel and composite specimens with and without connectors in the plastic zones have been tested under monotonic and cyclic seismic type loading.

• Steel and Composite Structures
• /
• v.15 no.3
• /
• pp.323-342
• /
• 2013

In the case of seismic-resistant composite dual moment resisting and eccentrically braced frames, the current design practice is to avoid the disposition of shear connectors in the expected plastic zones, and consequently to consider a symmetric moment or shear plastic hinges, which occur only in the steel beam or link. Even without connectors, the real behavior of the hinge may be different from the symmetric assumption since the reinforced concrete slab is connected to the steel element close to the hinge locations, and also due to contact friction between the concrete slab and the steel element. At a larger level, the structural response in the case of important seismic motions depends directly on the elasto-plastic behavior of elements and hinges. The numerical investigation presented in this study summarizes the results of elasto-plastic analyses of several steel frames, considering the interaction of the steel beam with the concrete slab. Several parameters, such as the inter-story drift, plastic rotation requirements and behavior factors q were monitored. In order to obtain accurate results, adequate models of plastic hinges are proposed for both the composite short link and composite reduced beam sections.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.5
• /
• pp.215-220
• /
• 2012

Miniature ultrasonic and tactile sensors on Si substrate have been proposed, fabricated and characterized to detect objects for a dexterous robot. The ultrasonic sensor consists of piezoelectric PZT thin film on a Pt/Ti/$SiO_2$ and/or Si diaphragm fabricated using a micromachining technique; the ultrasonic sensor detects the piezoelectric voltage as an ultrasonic wave. The sensitivity has been enhanced by improving the device structure, and the resonant frequency in the array sensor has been equalized. Position detection has been carried out by using a sensor array with high sensitivity and uniform resonant frequency. The tactile sensor consists of four or three warped cantilevers which have NiCr or $Si:B^+$ piezoresistive layer for stress detection. Normal and shear stresses can be estimated by calculation using resistance changes of the piezoresitive layers on the cantilevers. Gripping state has been identified by using the tactile sensor which is installed on finger of a robot hand, and friction of objects has been measured by slipping the sensor.

• Fashion & Textile Research Journal
• /
• v.15 no.1
• /
• pp.156-162
• /
• 2013

For the development of high quality textiles, silk fabrics were dyed repeatedly with persimmon juice by padding mangle. We evaluated the mechanical properties and hand value by Kawabata Evaluation system for dyed silk fabrics. The results obtained from this study were as follows. With the increase of repeating padding times of dyeing, the linearity load-extension curves of the silk fabrics were increased; however, the tensile resilience of fabrics decreased. The hysteresis values of shear force were increased without significant change of shear stiffness. The coefficient of friction values were also decreased and geometrical roughness values were increased. The silk fabrics dyed with persimmon juice had shown the thickness and weight grow as the number of padding increases. The hand values of silk fabrics which were classified into 6 items in the Kawabata Evaluation System, were evaluated as repeating times of dyeing with persimmon juice. The hand values of Koshi(stiffness) and Hari(anti-drape stiffness) were increased, whereas Shinayakasa (flexibility with soft feeling) and Fukurami(fullness and softness) were decreased by dyeing with persimmon juice. However there was no significant change in hand values according to repeating padding times of dyeing.