• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.183-185
• /
• 2005

In an attempt to optimize friction spot joining process of Mg alloys, effects of joining parameters such as rotating speed, plunging depth, and dwelling time on the joints properties were evaluated. Experimental tests were carried out for lap joined AZ31B-H24 sheets. A wide range of joining conditions could be applied to join Mg alloys without defects in the weld zone except for certain welding conditions with an insufficient heat input. The microstructures and hardness variations in the weld regions are discussed. For sound joints without defects, tensile shear strength of weld joints was higher approximately 116% than typical tensile shear strength of electrical resistance spot-welded joints for magnesium(Welding handbook, Vol 3, AWS).

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.316-318
• /
• 2007

Friction Spot Joining(FSJ) has a strong potential for aluminum alloy joining in automobile industries. The present paper focuses on the attempt to optimize the FSJ process for lap joining of A5052-H32 and A6061-T6 aluminum alloys. For A5052 maximum tensile shear strength has been observed for a tool rotating speed of 800rpm and for A6061 at 1000 rpm. Study on fracture modes of the tensile tested specimens of both A5052-H32 and A6061-T6 revealed, for high tensile strength values, plug fracture mode and lower tensile values, shear fracture mode. Above 2000 rpm distortion of the base metal, beside the tool shoulder was larger and plug fracture mode has been observed.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.177-179
• /
• 2005

In an attempt to optimize friction spot joining Process of Al alloys for automobiles, joining parameters such as tool rotating seed, plunging depth, and joining time on the joints properties were investigated. A wide range of joining conditions could be applied to join Al alloys for automobile without defects in the weld zone except for certain welding conditions with a lower heat input. for sound joints without defects, tensile shear strength of joints was higher than acceptable criteria of tensile shear strength of resistance spot welded joints for aluminum.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.821-824
• /
• 2009

In this study, a hydrogenated lecithin-containing nanoemulsion was prepared from hydrogenated lecithin and silicone oil. Tween-60 and liquid paraffin, widely known emulsifiers, were used as standard substances, and high shear was produced by utilizing a high shear homogenizer and microfluidizer. The properties of the nanoemulsion prepared with hydrogenated lecithin were evaluated by measuring interfacial tension, dynamic interfacial tension, droplet size, zeta-potential, friction force, skin surface hygrometery, and dermal safety. The interfacial tension of lecinol S10/silicone oil was lower than that of lecinol S10/liquid paraffin. The nanoemulsion prepared from hydrogenated lecithin shows lower zeta-potential, skin surface hygrometery, and friction force compared with a general emulsion. The silicone nanoemulsion prepared from hydrogenated lecithin showed a zero value in the patch test and thus exhibits high dermal safety.

• Journal of Korea Water Resources Association
• /
• v.32 no.4
• /
• pp.469-478
• /
• 1999

Explicit equations of minimum velocity, energy slope and pipe diameter are developed to ensure the cleaning of sewerage pipes. The equations of power form are employed for the estimation of critical shear stress of sediment particles and the friction factor of commercial pipes. They are all based on the existing laboratory data. Several cases are tested to check the values suggested in the manual, using the equations developed in the present study.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.3
• /
• pp.226-233
• /
• 1994

The present paper considers the method to estimate the bottom friction driven by waves and current on rough turbulent flow. Parameter adjusting technique is suggested for the computation of bed shear stress driven by uni-directional flow. and the value of parameter is determined by comparing the computational results against Bijker's laboratory data. For the computation of combined flow bottom shear stress, two methods are presented; one is the modified Bijker approach (BYO Model) and the other is the modified Fredsoe approach (FY Model). both of which are refined by the present writer. Both models are again refined in two aspects, and tested against the Bijker's laboratory data.

• Geomechanics and Engineering
• /
• v.28 no.1
• /
• pp.35-48
• /
• 2022

The effect of discrete polypropylene fibre reinforcement on shear strength parameters, tensile properties and isotropic index of stabilized compacted residual subgrade was investigated. Composites of compacted subgrade were developed from polypropylene fibre dosage of 0%, 1%, 2.5% and 4% and 3% cement binder. Saturated compacted soil benefited from incremental fibre dosage, the mobilized friction coefficient increased to a maximum at 2.5% fibre dosage from 0.41 to 0.58 and the contribution due to further increase in fibre dosage was marginal. Binder stabilization increased the degree of isotropy for unreinforced soil at lower fibre dosage of 1% and then decreased with higher fibre dosage. Saturation of 3% binder stabilized soil decreased the soil friction angle and the degree of isotropy for both unstabilized and binder stabilized soil increased with fibre dosage. The maximum tensile stress of 3% binder stabilized fibre reinforced residual soil was 3-fold that of 3% binder stabilized unreinforced soil. The difference in computed and measured maximum tensile and tangential stress decreased with increase in fibre dosage and degree of stabilization and polypropylene fibre reinforced soil met local and international criteria for road construction subgrade.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.206-215
• /
• 1993

The finite element method is applied to analyze the mechanism of metal cutting, especially micro metal cutting. This paper introduces some effects, such as constitutive deformation laws of workpiece material, friction of tool-chip contact interfaces, tool rake angle and also simulate the cutting process, chip formation and geometry, tool-chip contact, reaction force of tool. Under the usual plane strain assumption, quasi-static analysis were performed with variation of tool-chip interface friction coefficients and tool rake angles. In this analysis, cutting speed, cutting depth set to 8m/sec, 0.02mm, respectively. Some cutting parameters are affected to cutting force, plastic deformation of chip, shear plane angle, chip thickness and tool-chip contact length and reaction forces on tool. Several aspects of the metal cutting process predicted by the finite element analysis provide information about tool shape design and optimal cutting conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.772-781
• /
• 2020

A direct shear member resists external forces through the shear transfer of reinforcing bars placed at the concrete interface. The current concrete structural design code uses empirical formulas based on the shear friction analogy, which is applied to the horizontal shear of concrete composite beams. However, in the case of a member with a large amount of reinforcing bars, the shear strength obtained through the empirical formula is lower than the measured value. In this paper, the limit state of newly constructed composite beams on an existing concrete girder is defined using stress field theory, and material constitutive laws are applied to gain horizontal shear strength while considering the tension-stiffening and softening effects of concrete struts. A simplified method of calculating the shear strength is proposed, which was validated by comparing it with the related design code provisions. As a result, it was confirmed that the method generally shows a similar tendency to the experimental results when the shear reinforcing bar yields, unlike the regulations of the design code, where differences in the predicted value of shear strength occur according to the shear reinforcement ratio.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.834-845
• /
• 1995

An experimental study is made in a nearly two-dimensional 90.deg. curved duct to investigate the effects of interaction between streamline curvature and mean strain on turbulence. The initial shear at the entrance to the curved duct is varied by an upstream shear generator to produce five different shear conditions ; a uniform flow (UF), a positive weak shear (PW), a positive strong shear(PS), a negative weak shear (NW) and a negative strong shear(NS). With the mean field data of the case UF, variations of the momentum thickness, the shape factor and the skin friction over the convex(inner) surface and the concave (outer) surface are scrutinized quantitatively in-depth. It is found that, while the pressure loss due to curvature is insensitive to the inlet shear rates, the distributions of wall static pressure along both convex and concave surfaces are much influenced by the inlet shear rates.