• 콘크리트학회논문집
• /
• 제15권6호
• /
• pp.820-828
• /
• 2003

최근의 연구를 통해서, ACI 전단 규준은 크기가 크고 인장철근비가 낮은 보에서 비보수적 예측을 보이는 반면 깊은 보에 대해서는 보수적 예측을 보임을 알 수 있다. 이러한 ACI 전단 규준이 가지고 있는 문제점을 수정하기 위해, 본 연구에서는 스터럽이 없는 고강도 철근 콘크리트 보의 전단강도 계산시 크기효과와 아치작용을 고려한 극한 전단강도 예측식을 제안하였다. ACI 전단 규준의 수정을 위해 포함될 항은 과학적 이론 및 분석에 근거한 $f_{sr}$ (dr), $f_{si}$ (${\rho}$)와 $f_{aa}$ (a/d)항이며, 선형 및 비선형 회귀분석을 통해 도출되었다. 기존의 실험 데이터 약 300여 개를 이용하여 각각의 변수에 대한 제안식의 검증 및 제안식과 ACI 318-99 code, CEB-FIP model code, Kim &Park 식 및 Zsutty 식과의 비교를 수행하였다. 제안식은 간단한 형태를 지니고 있지만, 경제적이면서도 합리적인 안전율을 확보할 수 있는 전단강도를 예측한다. 따라서 제안식은 실무에서 콘크리트 구조물의 전단설계에 적용 가능할 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제76권3호
• /
• pp.311-324
• /
• 2020

Until now, a comparative study on fully and partially-connected steel shear walls leading to enhancing strength and stiffness reduction of partially-connected steel plate shear wall structures has not been reported. In this paper a number of 4-story and 8-story steel plate shear walls, are considered with three different connection details of infill plate to surrounding frame. The specimens are modeled using nonlinear finite element method verified excellently with the experimental results and analyzed under monotonic loading. A comparison between initial stiffness and shear strength of models as well as percentage of shear force by model boundary frame and infill plate are performed. Moreover, a comparison between energy dissipation, ductility factor and distribution of Von-Mises stresses of models are presented. According to the results, the initial stiffness, shear resistance, energy dissipation and ductility of the models with beam-only connected infill plates (SSW-BO) is found to be about 53%, 12%, 15% and 48% on average smaller than those of models with fully-connected infill plates (SPSW), respectively. However, performance characteristics of semi-supported steel shear walls (SSSW) containing secondary columns by simultaneously decreasing boundary frame strength and increasing thickness of infill plates are comparable to those of SPSWs. Results show that by using secondary columns as well as increasing thickness of infill plates, the stress demands on boundary frame decreases substantially by as much as 35%. A significant increase in infill plate share on shear capacity by as much as 95% and 72% progress for the 4-story SSW-BO and 8-story SSSW8, respectively, as compared with non-strengthened counterparts. A similar trend is achieved by strengthening secondary columns of 4-story SSSW leading to an increase of 50% in shear force contribution of infill plate.

• 전산구조공학
• /
• 제10권4호
• /
• pp.281-290
• /
• 1997

현행 내진설계 규준에서 사용하고 있는 반응수정계수는 설계지진하중과 유사한 지진발생시 구조물이 비선형 거동을 하도록 탄성응답에서 요구되는 밑면전단력 값을 낮추는 계수라 할 수 있다. 따라서 반응수정계수는 하중저감계수(force reduction factor)라고 할 수 있으며, 이러한 값들은 경험적으로 결정된 것이어서 예상지진에 대하여 구조설계자가 설계한 건물이 어느정도의 비선형 거동을 할지는 예측하기가 힘들다. 본 연구에서는 목표가 되는 연성비(target ductility ratio)에 따라 요구되는 밑면전단력의 값을 구하고 이를 규준에서 요구하는 값과 비교할 것이다. 만약 요구되는 값이 규준 값 보다 크다면 이는 구조물이 가지는 부가강도(overstrength)나 잉여력(redundancy)이 담당해야 한다. 모멘트연성골조 건물을 설계한 후 이를 push-over 해석에 의하여 부가강도를 찾아 보아 요구강도와 비교할 것이다.

• Computers and Concrete
• /
• 제10권4호
• /
• pp.361-377
• /
• 2012

Four Reinforced Concrete (RC) single span structural walls having various opening sizes and locations were constructed and tested under lateral reversed cyclic loading at the structural laboratory of Kyoto University. These specimens were scaled to 40% and represented the lower three stories of a six-storied RC building. The main purposes of the experimental tests were to evaluate the shear behavior and to identify the influence of opening ratios on the cracks distribution and shear strength of RC structural walls. The shear strength of the specimens was estimated by combining the shear strength of structural wall without openings and the reduction factor that takes into account the openings. Experimental and analytical results showed that the shear strength was different depending on the loading direction due to opening locations. A two-dimensional finite element analysis was carried out to simulate the performance of the tested specimens. The constructed finite elements model simulated the lateral load-drift angle relations quite well.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1997년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 1997
• /
• pp.193-200
• /
• 1997

Current seismic design code is based of the assumption that the designed structures would be behaved inelastically during a severe earthquake ground motion. For this reason, seismic design forces calculated by seismic codes are much lower than the forces generated by design earthquakes which makes structures responding elastically. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factors known as "response modificaion factor". Because these factors were determined empirically, it is difficult to know how much inelastic behaviors of the structures exhibit. In this study, base shear forces required to maintain target ductility ratio were first calculated from nonlinear dynamic analysis on the single degree of freedom system. And then, base shear foeces specified in seismic design code compare with above results. If the strength(base shear) required strength should be filled by overstrength and/or redundancy. Therefore, overstrength of moment resisting frame structure will be estimated from the results of static nonlinear analysis(push-over analysis).analysis).

• 지질공학
• /
• 제27권1호
• /
• pp.31-40
• /
• 2017

한계평형법에 의한 비탈면 안정성 해석은 활동면을 반복적인 해석 후 임계면을 설정하여 해석을 수행하고, 지반이 균질한 경우에만 적용이 가능하며, 안전율만 산정 할 수 있는 단점이 있다. 그러나 강도감소법을 적용한 해석에서는 수행자가 여러 가지 측면에 대해서 판단하고, 안전율을 산정 할 수 있는 장점 등이 있다. 본 연구에서는 동일한 크기의 비탈면을 대상으로 한계평형해석과 강도감소법을 활용하여 경사도 변화에 따른 두 해석법 간의 안전율 변화 양상과 점착력과 내부마찰각의 변화에 따른 안전율 변화 추이를 비교 분석하였다. 각각의 해석법에 따른 안정해석 분석 결과 지반내 응력, 변위와 변형률 등을 종합적으로 검토할 수 있는 강도감소법이 활용도가 높을 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.434-443
• /
• 2009

Slope stability analysis is an essential part of rock slope design. For highly fractured rock, the limit equilibrium method (LEM) based slope stability analysis with a circular failure surface is often carried out assuming the rock mass behaves more or less as a continuum. This paper examines first, the applicability of the finite-element method (FEM) based shear strength reduction (SSR) technique for highly fractured rock slope, and second the use of Mohr-Coulomb (MC) failure criterion in conjunction with generalized Hoek-Brown (HB) failure criterion. The numerical results on a number of cases are compared in terms of the factor of safety (FS). The results indicated that the FEM-based SSR technique yields almost the same FSs from LEM, and that the MC and HB failure criteria yield almost identical FSs when the strength parameters for MC failure criterion are obtained based on the modified HB failure criterion if and only if value of the Hoek-Brown constant $m_i$ is smaller than 10 and slope angle is smaller than 1:1, otherwise MC failure criteria over-estimate the factor of safety.

• 한국터널지하공간학회 논문집
• /
• 제9권2호
• /
• pp.99-107
• /
• 2007

지보재의 파괴가 고려된 터널의 안전율을 산정하는 방법으로 숏크리트 내에 발생하는 응력이 허용응력을 초과하면 숏크리트가 파괴된다고 가정하고 전단강도 감소기법을 이용하여 지반과 숏크리트의 파괴를 고려한 안전율을 구하는 방법이 유광호 등(2000)에 의해 제시되 바 있고, 유광호 등(2005)과 한동식 등(2006)에 의해 꾸준히 수정 보완되었다. 본 논문에서는 터널의 안전율을 산정함에 있어 시공단계를 고려할 수 있도록 기존 routine을 수정 보완하였다. 또한, 전단강도 감소기법을 사용하여 연속체요소와 보요소로 숏크리트를 모델링하고, 허용응력설계법에 근거하여 파괴를 판단함으로서 터널의 안전율을 정량적으로 산정하는 기존 연구와의 비교를 통해 적정 숏크리트의 모델링 방법을 제시하고자 한다.

• Geomechanics and Engineering
• /
• 제13권3호
• /
• pp.517-533
• /
• 2017

In this paper, with a graphical approach, a series of stability charts for homogeneous slopes with benches are presented based on the upper bound limit analysis theory and strength reduction technique. The objective function of the slope safety factor $F_s$ is optimized by the nonlinear sequential quadratic programming, and a substantial number of examples are illustrated to use the stability charts for homogeneous slopes with benches driven by only the action of the soil weight. These charts can be applied to quick and accurate estimations of the stability status of homogeneous slopes with benches. Moreover, the failure modes and the formula for safety factor Fs of homogeneous slopes with benches are provided to illustrate the stability analysis of slopes with benches, which is validated by samples.

• Computers and Concrete
• /
• 제14권1호
• /
• pp.19-40
• /
• 2014

Reinforced concrete deep beams are structural beams with low shear span-to-depth ratio, and hence in which the strain distribution is significantly nonlinear and the conventional beam theory is not applicable. A strut-and-tie model is considered one of the most rational and simplest methods available for shear strength prediction and design of deep beams. The strut-and-tie model approach describes the shear failure of a deep beam using diagonal strut and truss mechanism: The diagonal strut mechanism represents compression stress fields that develop in the concrete web between diagonal cracks of the concrete while the truss mechanism accounts for the contributions of the horizontal and vertical web reinforcements. Based on a database of 406 experimental observations, this paper proposes a new strut-and-tie-model for accurate prediction of shear strength of reinforced concrete deep beams, and further improves the model by correcting the bias and quantifying the scatter using a Bayesian parameter estimation method. Seven existing deterministic models from design codes and the literature are compared with the proposed method. Finally, a limit-state design formula and the corresponding reduction factor are developed for the proposed strut-andtie model.