• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.219-222
• /
• 2003

Substantial experimental and theoretical work exists on the bond characteristics of FRP-concrete adhesive joints. Experimental studies show that the bond strength cannot always increase with an increase in the bond length, and that the ultimate strength is strongly influenced by the concrete strength. To solve this feature, analytic solutions based on fracture mechanics are widely used, and the local shear stress-slip curve with a softening branch is known as more rational model. The analytic solution, however, cannot describe various shapes of model curve. In this study, numerical method using interface element is introduced to express various shapes of model curve. Characteristics of adhesive joint is investigated for the shapes of the model curve and their parameters. And the numerical solutions are compared with the test results of CFRP sheet adhesive joints.

• Steel and Composite Structures
• /
• 제8권3호
• /
• pp.179-200
• /
• 2008

This paper reports the results of a recent experimental study into the behavior of welded fin-plate connections to both hollow and concrete filled tubular (CFT) columns under shear. Experiments have been performed at both ambient and elevated temperatures with the aid of an electric kiln. The observed failure modes include fracture of the fin plate and tearing out of the tube around the welds. By considering the results of previously published research, the current design method for similar connections under purely tensile load, in CIDECT Guide 9, based on a deformation limit of 3% of the tube width is shown to be inadequate when evaluating the ultimate strength of such connections. By comparing the results from the current test program which failed in the fin-plate with Eurocode guidance for failure of a fin-plate alone under shear and bending load it is shown that the column face influences the overall connection strength regardless of failure mode. Concrete in-fill is observed to significantly increase the strength of connections over empty specimens, and circular column specimens were observed to exhibit greater strength than similarly proportioned square columns. A finite element (F.E.) model, developed using ABAQUS, is presented and validated against the experimental results in order that extensive parametric tests may be subsequently performed. When validating the model against elevated temperature tests it was found that using reduction factors suggested in published research for the specific steel grades improved results over applying the generic Eurocode elevated temperature steel strength reduction factors.

• Geomechanics and Engineering
• /
• 제13권4호
• /
• pp.535-570
• /
• 2017

There are only few cases where cause and location of failure of a rock structure are limited to a single discontinuity. Usually several discontinuities of limited size interact and eventually form a combined shear plane where failure takes place. So, besides the discontinuities, the regions between adjacent discontinuities, which consist of strong rock and are called material or rock bridges, are of utmost importance for the shear strength of the compound failure plane. Shear behaviour of persistent and non-persistent joint are different from each other. Shear strength of rock mass containing non-persistent joints is highly affected by mechanical behavior and geometrical configuration of non-persistent joints located in a rock mass. Therefore investigation is essential to study the fundamental failures occurring in a rock bridge, for assessing anticipated and actual performances of the structures built on or in rock masses. The purpose of this review paper is to present techniques, progresses and the likely future development directions in experimental testing of non-persistent joint failure behaviour. Experimental results showed that the presence of rock bridges in not fully persistent natural discontinuity sets is a significant factor affecting the stability of rock structures. Compared with intact rocks, jointed rock masses are usually weaker, more deformable and highly anisotropic, depending upon the mechanical properties of each joint and the explicit joint positions. The joint spacing, joint persistency, number of rock joint, angle of rock joint, length of rock bridge, angle of rock bridge, normal load, scale effect and material mixture have important effect on the failure mechanism of a rock bridge.

• 기술사
• /
• 제19권4호
• /
• pp.5-10
• /
• 1986

On SWS 41 Plates jointed by the F11T M 20 high strength bolts the study on stress behavior and safety degree until rupture in static tensile tests were performed. By these results, in case of no clamping force stress concentration was extremed for strain of about 10% higher ratio. Elastic strain occurred to change of test specimens depth by the load and plastic strain occurred to local minute sleep after elastic strain. compared shear stress with tension stress from the fracture load it was showned lower values than the maximum shear stress theory and stress strain energy theory.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.395-396
• /
• 2023

The current building structural standards present design requirements for the vertical construction joint of a slurry wall when it is used as a permanent wall. This paper proposes design methods and considerations according to the requirements of the relevant standards.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.283-289
• /
• 2000

The panel shear and bearing strengths determining the seismic resistance of reinforced concrete column-to-steel beam connections are predicted by various methods for four previously tested exterior beam-column joints. The analytical approach to model the joint deformation is also examined. Several analyses incorporating the deformations of panel shear and bearing in the joint are demonstrated using a analyses incorporating the deformations of panel shear and bearing in the joint are demonstrated using a fairly simple connection model in the commercial packages such as Drain2dx and IDARC. The strength prediction results indicated that the ASCE method with the modifcation of the comprssion strut contribution is th most accurate. It is also considered that the analytical model presented including the joint deformation can be used for the overall analysis

• 한국지진공학회논문집
• /
• 제5권2호
• /
• pp.73-82
• /
• 2001

본 연구는 실험적 방법과 해석적 방법을 통하여 반복하중을 받는 ├형 철근콘크리트 접합부의 전단특성을 파악함을 목적으로 한다. ├형 접합부는 고강도 재료의 사용으로 인한 체적의 감소 뿐만 아니라, 지진발생 시 반복하중의 작용으로 인한 변동축력 등으로 , 구조적으로 취약한 부분이 될 가능성이 있다. 따라서 본 연구에서는 ├형 접합부의 전단특성을 파악하기 위하여 기동축력, 콘크리트 압축강도, 접합부 전단보강근비를 변수로 한 12개의 실험체를 제작하여 가력실험을 수행하였다. 또한, 유한요소 해석을 수행하여 본 실험결과와의 비교 검토를 통하여 타당성을 검토한 후, 기둥축력과 콘크리트 압축강도의 변화에 대한 변수해석을 통하여 접합부의 전단강도에 미치는 변수는 영향을 파악하였으며, 실험에 의한 실험체의 전단내력을 기존에 제안된 AIJ, ACI 규준 등과 비교 검토하였다. 본 연구의 결로부터 기둥축력과 콘크리트 압축강도가 ├형 철근콘크리트 접합부의 전단강도에 미치는 영향을 확인하였다.

• 한국지반공학회논문집
• /
• 제17권4호
• /
• pp.301-315
• /
• 2001

본 연구에서는 최근 5년간 국내 각 지역에서 채취한 802개의 절리면 시료에 대하여 전단시험을 실시하여 얻은 결과를 이용하여, 절리면의 여러 공학적 성질들을 조사, 연구하였다. 절리면 전단시험에서 얻어진 최대마찰각 및 잔류마찰각을 지체구조별, 암종별로 분류하고 통계적으로 구하였으며, Barton의 전단강도식의 입력변수인 JRC, JCS를 측정하고 Barton식의 적용성에 대해서도 검토하였다. 그 결과 설계의 기초자료로 활용할 수 있는 지역별, 주요 암종별 최대마찰각, 잔류마찰각을 제시하였다. 또한, JRC, JCS, 수직응력에 따른 마찰각과 전단강성 및 팽창각의 변화를 분석하였다. 마지막으로, Barton의 식에서 구한 이론적 전단강도와 이 실험에서 얻어진 전단강도를 비교한 결과, Barton의 경험식은 높은 상관도로 암석 절리면 전단강도를 예측할 수 있음을 확인하였다.

• 한국지반환경공학회 논문집
• /
• 제7권3호
• /
• pp.31-41
• /
• 2006

화강암 시료에서 절리면 시편의 크기효과를 연구하기 위해 6가지 크기의 인공절리 시편을 제작하여 직접전단시험을 수행하였다. 각기 다른 수직응력 0.29~2.65MPa과 절리면의 거칠기 파라미터에 대하여 최대전단응력, 잔류전단응력, 전단강성 및 팽창각이 이 연구를 위해 평가되었다. 거칠기 파라미터중 절리거�s계수(JRC)와 절리면의 압축강도(JCS)는 시편의 크기가 증가할수록 감소하였다. 시편의 절리면적이 $12.25cm^2$에서 $361cm^2$으로 증가할 경우 최대전단응력은 약 56~67%, 잔류전단응력은 18~44%까지 감소하였다. 또한 팽창각은 수직응력이 0.29 MPa일 때 $27^{\circ}$, 2.65 MPa일 때 $6^{\circ}$의 변화를 보였다. JRC 크기효과를 고려한 전단강도 관계식이 Barton의 경험식과 비교되었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.22-23
• /
• 2016

This study aims to derive the optimal condition that ensures the monolithicity of ultra-high performance concrete (UHPC), through the evaluation of bonding shear performance with respect to the time of cold joint occurrence during the placement. From the direct shear test, while the normalized bonding shear strength reduction of UHPC with the delay time of 15 minutes was the lowest at around 8%, a dramatic degradation of bonding shear performance was observed after 15 minutes. XRD analysis of the middle and surface sections was performed in order to analyze the composition of the thin film formed at the surface of UHPC, and as a result, the main ingredient appeared to be SiO₂ from the XRD pattern of middle and surface sections, which is believed to be the result of the rising of SiO₂-based filler, used as anadmixture in this study, toward the surface, due to its low specific gravity.