• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.9 s.339
• /
• pp.57-64
• /
• 2005

A Piconet consists of Master device and several Slave devices. Master and Slave devices are transmitted using TDD (Time Duplex Oivision) in a Piconet. A Scattemet constructed by several Piconets communicates by a Piconet. Bluetooth Specification defines the meaning of a Scatternet. But the formation and scheduling method is not defined. For the efficient formation of a Scatternet, the preceding research proposes a tree-shape topology Scatternet. But this research passes over the characteristic of Bluetooth transmission carried out by a Piconet in the Scattemet. So this Paper proposes a efficient throughput tree formation Scatternet algorithm To improve the throughput of a Scatternet, this paper proposes a tree tolopology that guarantees the efficient throughput of a Piconet

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.439-445
• /
• 2013

Both an unreinforced $Al_2O_3$/Al matrix and a ${\alpha}-Al_2O_3$ particulate reinforced composite have been produced by the oxidation of an Al surface doped with NaOH in the absence of any other dopant. Fabrication of the matrix was initiated by the formation of $NaAlO_2$, which provides a favorable surface structure for the matrix formation by breaking the protective $Al_2O_3$ layer on Al. During the matrix growth, the external surface of the growth front was covered with a very thin sodium-rich oxide. A cyclic formation process of the sodium-rich oxide on the growth surface was proposed for the sodium-induced directed metal oxidation process. This process involves dissolution of the sodium-rich oxide, motion of Na to the growth front, and re-formation of the oxide on the surface. Near-net-shape composites were fabricated by infiltrating an $Al_2O_3$/Al matrix into a ${\alpha}-Al_2O_3$ particulate preform, without growth barrier materials. The infiltration distance increased almost linearly in the NaOH-doped preform.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.819-824
• /
• 2010

We report the laser-induced formation of peanut-shaped gold nanoparticles (Au nanopeanuts) and gold nanowires (AuNWs), and their morphological properties. Pulsed laser irradiation of citrate-capped gold nanoparticles at 532 nm induces fragmentation, spherical growth, the formation of Au nanopeanuts, and the formation of AuNWs, sequentially. High-resolution transmission electron microscopy images reveal that the Au nanopeanuts are formed by instantaneous fusion of spherical nanoparticles in random orientation by laser heating. Furthermore, Au nanopeanuts are bridged in a linear direction to form AuNWs by an amorphous accumulation of gold atoms in the junction. The laser-produced Au nanopeanuts and AuNWs slowly disintegrate, restoring the spherical shape of the original Au nanoparticles when the laser irradiation is stopped. The addition of citrate effectively prevents them from transforming back to the nanospheres.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.8-16
• /
• 2013

As the energy consumption increases rapidly, power generation needs the high energy efficiency continuously. To achieve the high efficiency of power generation, the materials used have to endure the higher temperature and pressure. The 9-12%Cr steels possess good mechanical properties, corrosion resistance, and creep strength in high temperature due to high Cr contents. Therefore, the 9-12%Cr steels are widely used for the high-temperature components in power plants. Even though the steels usually have a fully martensitic microstructure, they are susceptible to the formation of ${\delta}$-ferrite specifically during the welding process. The formation of ${\delta}$-ferrite has several detrimental effects on creep, ductility and toughness. Therefore, it is necessary to avoid its formation. As the volume fraction of ${\delta}$-ferrite is less than 2% in microstructure, it has the isolated island morphology and causes no significant degradation on mechanical properties. For ${\delta}$-ferrite above 2%, it has a polygonal shape affecting the detrimental influence on the mechanical properties. The formation of ${\delta}$-ferrite is affected by two factors: a chemical composition and a welding heat input. The most effective ways to get a fully martensite microstructure are to reduce the chromium equivalent less than 13.5, to keep the difference between the chromium and nickel equivalent less than 8, and to reduce the welding heat input.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2004.10a
• /
• pp.22-28
• /
• 2004

Pit and rim formation on the Acrylonitrile Butadiene Styrene(ABS) plastic surface was evaluated after it was irradiated by $CO_2$ and Nd:YAG laser beams. Our results show that thermal effect floor was well observed at the outer wall of pit with $CO_2$ laser irradiated while it was not the case with Nd:YAG laser irradiated. Also the volume and depth of pit formation increase proportionally with the energy intensities of two laser irradiations, but there are significant differences in the slope, width, and FWHM of the Pit formation with two types of laser irradiations. This result shows that $CO_2$ laser irradiation leads to better cooling contraction effect while Nd:YAG laser irradiation induces better recoil pressure effect during the interaction between ABS plastic and laser beam irradiation. The shape of the laser marking could vary significantly depending on the traveling path of molten plastic during injection molding of ABS plastic. Therefore, the selection of material and molding process can have a great impact on the performance of optical storage media.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.1
• /
• pp.95-101
• /
• 2000

The effect of surface contact angle on the behavior of frost formation in a fin-tube heat exchanger is investigated experimentally. It is shown that both heat exchangers with hydrophilic and hydrophobic surfaces appear to have a better thermal performance than bare aluminium heat exchanger, but the improvements are very small. There is a little increase in the amount of the frost deposited onto the heat exchanger with both hydrophilic and hydrophobic surface. However, the effect of contact angle on the frost density is observed ; the frost with high density forms on the heat exchanger with hydrophilic surface ; and the frost with low density is deposited onto the heat exchanger with hydrophobic surface when compared with the frost deposited onto the heat exchanger with bare aluminium surface. This may be attributed to the fact that the shape of water droplets which condense on the surface of heat exchanger at the early stage of frosting varies with contact angle, and thus makes a difference on the structure of frost formation. From the experiments with different relative humidity of inlet air, it is shown that the variations of operating parameter make no influence on the effect of surface contact angle on the frosting behavior in the heat exchanger.

• Economic and Environmental Geology
• /
• v.56 no.4
• /
• pp.397-408
• /
• 2023

A total of 64 specimens of trace fossils were collected from the Jinju Formation of the construction site of Jinju Aviation Industrial Complex, and from the Haman Formation of Namhae Gain-ri fossil site. The fossils are continuously and regularly meandering sine-curve in shape. The fossil varies in morphology: width between 0.2 and 5.6 mm, wavelength between 1.5 and 28 mm, and amplitude between 0.9 and 7.9 mm; the Jinju specimens are commonly wider than the Haman ones. The ratio of wavelength to amplitude is more or less regular regardless of width of the specimen, and the linear correlation of the ratios shows that the Jinju specimens fit better than the Haman specimens. Taking all morphometric parameters, specimens in all size ranges are temporarily identified as ichnospecies Cochlichnus anguineus. In order to obtain more distinct and clearer images of Cochlichnus, we selected two specimens and applied a new imaging technology RTI. For photography of the trace fossils, 50 to 80 images were taken per set with photometric lighting close to the surface and horizontally. RTI technology clearly showed that the images of tiny fossils were improved: the surface contrast become sharper and messy and unnecessary information disappeared. Currently, RTI technology is used in many fields including preservation of cultural properties and archaeology. As a consequence, we hope to apply this technique to the field of paleontology, especially to the study of trace fossils of very small size.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.9
• /
• pp.148-155
• /
• 1995

The object of this study is to achieve a gteater understanding of meterial removal process and its mechanism. In this study, some applications of finite element techniques are applied to analyze the chip formation and cutting heat generation mechanism of metal cutting. To know the effect of cutting parameters, simulations employed some independent cutting variables change, such as constitutive deformation laws of workpiece and tool material, frictional coefficients and tool-chip contact interfaces, cutting speed, tool rake angles, depth of cut and this simulations also include large elastic-plastic defor- mation, adiabetic thermal analysis. Under a usual plane strain assumption, quasi-static, thermal-mechanical coupling analysis generate detailed informations about chip formation process and cutting heat generation mechanism Some cutting parameters are affected to cutting force, plastic deformation of chip, shear plane angle, chip thickness and tool-chip contact length and reaction force on tool, cutting temperature and thermal behavior. Several aspects of the metal cutting process predicted by the finite element analysis provide information about tool shape design and optimal cutting conditions.

• Korean Journal of Plant Resources
• /
• v.19 no.2
• /
• pp.199-203
• /
• 2006

The marketability of soybean sprout mainly depends on shape such as hypocotyl thickness and presence of lateral root formation, etc. To clarify the effects of agitating culture box on growth and shape of soybean sprouts, different agitation frequency (0, 3, 5 times day-1) and duration (0, 1, 2, 3 days) were applied during sprout cultivation. More frequent and longer agitation resulted in less lateral root formation and shorter hypocotyl length, while total lengths were not affected by agitation due to agitation-induced root length increment. Agitation also increased the diameter of hypocotyl's hook pin, but not the middle part. Unlike morphological characteristics, the growth of sprouts as measured by fresh and dry weight of cotyledon, hypocotyl, root were not affected by agitation. In conclusion, it is very likely that agitating culture box during sprout cultivation may alter the shape of soybean sprouts without affecting growth of sprouts.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.5
• /
• pp.246-250
• /
• 2009

The Ni formation behavior from the reduction of NiO nano crystals in the $H_2/N_2$ gas mixtures. The NiO nano crystals were synthesized by heat-treating nickel nitrate$(Ni(NO_3)_2\cdot6H_O)$ in the air at $500^{\circ}C$, and had an octahedral shape and the particle size of 200~500 nm. The NiO nano-crystals had well-developed (111) planes which is hardly formed in normal synthetic conditions. The reduction process was carried out at 300 and $600^{\circ}C$ for 15 and 60 minutes, respectively. When the NiO nano-crystals were reduced at $300^{\circ}C$, the Ni particles sustained the same octahedral shape as NiO, while Ni particles were to agglomerate at $600^{\circ}C$.