• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.36 no.1
• /
• pp.20-36
• /
• 2024

In this study, probabilistic models for the wave- and lifting forces were derived directly from long-term in-situ wave data embedding the Korean marine environment characteristics varying from sea to sea based on the Three-Parameter Weibull distribution. Korean marine environment characteristics varying from sea to sea carved out their presence on the probability coefficients of probabilistic models for wave- and lifting forces. Energetic wave conditions along the southern coast of Korea distinguish themselves from the others with a relatively large scale coefficient, small location coefficient, and shape coefficient around 1.3. On the other hand, mild marine environment along the western coast has a small variability, leading to small scale-coefficient, large location coefficient and shape coefficient around 2.0. In the sea off Mokpo, near the boundary between the South- and West Seas, marine environment was characterized by small scale-coefficient, large location coefficient, and shape coefficient around 1.2, implying that marine environments characteristics of the South-and West Sea coexist in the sea off Mokpo.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.158-160
• /
• 2005

Zener coefficient on cubic shaped particle was proposed. Most previous researches about Zener coefficient were developed on the assumption that the shape of particle is spherical. But, some particle has other shape, and modification of Zener coefficient needs with shape of particle. In this research, TiN particle that has a cubic shape was considered. A Zener coefficient of a cubic shape TiN was theoretically calculated with appropriate assumptions. And, using a semi-empirical method, Zener coefficient was also measured. Finally, the proposed Zener coefficient was proved by comparing with experimentally measured data.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.302-305
• /
• 2005

In this study, settlement characteristics of 38 CFRD was investigated from monitoring data and the method to estimate the dam settlements considering valley shape during constructions was proposed. The construction modulus of dam was found to be dependent on void ratios and valley shape factor. The construction modulus varied with valley shape and decreased with increasing void ratio. Also, the modulus was increased when the shape coefficient was less than 4. The settlement investigation results showed that the total settlement was proportional to the value of the settlement coefficient multiplied by the shape coefficient divided by void ratio.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.462-469
• /
• 2010

Gas-liquid 2 phase processes are usually used in chemical, biochemical, environmental engineering and food process. For optimizing these processes, understanding bubble's precise movement and shape are needed. Bubble's movement and shape are effected by liquid's properties-viscosity, surface tension and bubble's properties-size, velocity. This paper deals with experimental data of bubble's movement and shape in high viscous silicone oil. Also, drag coefficient and deformation factor given by other researcher's papers and books are used to predicting and comparing bubble's terminal velocity, drag coefficient, deformation factor and shape with experimental value. Experimental data show that bubble moves faster when it moves in lower viscous silicone oil and it's drag coefficient is bigger when it moves in high viscous silicone oil. Bubble's shape is close to sphere when moving in high viscous silicone. Formulas proposed by Batchelor expect most accurate prediction for bubble's velocity and drag coefficient. Bubble's 2D shape predicted by Batchelor's energy balance, drag coefficient and deformation factor show excellent agreement with experimental bubble's 2D shape.

• The korean journal of orthodontics
• /
• v.13 no.1
• /
• pp.105-114
• /
• 1983

the author studied the corelativity between the head and face and the maxillary arch in Korean. This study was undertaker in 336 persons at age from 9 to 19 years who had normal occlusion by means of angle's classification. The following results were obtained. 1. The corelative coefficient between the Height of Head and Face (H.H.F.) and the Arch Length (A.L.) was 0.203-0.543, 2. The corelative coefficient between the Bizygomatic width (Z.W.) and the Bicanine width (C-C) was 0.203-0.543. 3. The corelative coefficient between the Bizygomatic width (Z.W.) and the Bimolar width (M-M) was 0.206-0.600. 4. The corelative coefficient between the Face shape (Index a) and Maxillaxy arch shape (In-dex c) was 0.232-0.404. 5. The corelative coefficient between the Face shape (Index a) and Maxillary arch shape (Index d) was 0.221-0.401. 6. There was no corelativity between the Anterior-posterior width of head (A.P.W.) and Arch Length A.L.), Head shape (Index b) and Maxillary arch shape (Index c, Index d).

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.677-682
• /
• 2012

For the product with small diameter, long column, and parabolic shape, the forging formability of the high-carbon steel wire rod was investigated in this study. By using the three-dimensional finite element method, the formability of wire was reviewed by forming analysis for the desired parabolic shape of local part. Analysis results due to forging direction, forging velocity, friction coefficient and constraint location were also investigated. On the basis of these results, it is noted that the forging direction has the big influence when the product with long column is forged. As the forging velocity increases, buckling tends to be limited and formability of parabolic shape is improved. By constraining the lower parabolic shape part to suppress plastic strain, the effect depending on friction coefficient is not almost appeared. And good parabolic shape is obtained at the region of the forging velocity of more than 0.5 m/s.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.4
• /
• pp.158-162
• /
• 2017

This paper did basic study on the vertical-axis wind turbine. Namely, This paper was try to find the optimum conditions by using the ANSYS CFX simulation program through the changes of the main-blade angle and sub-blade angle. Main-blade Shape #4 angle $45^{\circ}$ compared to others Shape angle $0^{\circ}$ was increased by 157.2[%] to 263.2[%] in the power output and was increased by 110[%] to 250[%] in the power coefficient. Also, when the Shape #5 Fin length of main-blade doubles, because the power output was 70.8[%] compared to Shape #1 and 27.5[%] compared to Shape #4, and the power coefficient was 60[%] compared to Shape #1 and 28.6[%] compared to Shape #4, the power output and the power efficiency were rather reduced. The output current of Shape #4 was increased 109.9[%] compared to Shape #1 and increased 250[%] compared to Shape #5, and The output voltage of Shape #4 was increased 22.5[%] compared to Shape #1 and increased 3.7[%] compared to Shape #4.

• The Korean Journal of Applied Statistics
• /
• v.32 no.1
• /
• pp.15-27
• /
• 2019

The reliability of the data means the overall consistency of the measurement results. Methods for evaluating reliability have been continuously studied because it affects the results of the statistical analysis. Cronbach's ${\alpha}$ coefficient or intraclass correlation coefficient is used for reliability evaluation; however, these measures cannot be applied to data consisting of three-dimensional coordinates to represent an object. In this study, we propose a measure to evaluate the reliability of three dimensional shapes based on statistical shape analysis that is made possible by extracting the shape information from the measured three dimensional coordinates and decomposing the shape variation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.2
• /
• pp.58-62
• /
• 2004

The shape evolution of the interface void of copper metallization for intergrated circuits under electromigration stress is modeled. A 2-dimensional finite-difference numerical method is employed for computing time evolution of the void shape driven by surface diffusion, and the electrostatic problem is solved by boundary element method. When the diffusion coefficient is isotropic, the numerical results agree well with the known case of wedge-shape void evolution. The numerical results for the anisotropic diffusion coefficient show that the initially circular void evolves to become a fatal slitlike shape when the electron wind force is large, while the shape becomes non-fatal and circular as the electron wind force decreases. The results indicate that the open circuit failure caused by slit-like void shape is far less probable to be observed for copper metallization under a normal electromigration stress condition.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.5
• /
• pp.389-395
• /
• 2017

This paper showed the difference in the optimum conditions by using the ANSYS CFX simulation program with the changes of the main-blade angle and sub-blade angle. Main-blade Shape 4,which had angle $45^{\circ}$ while other Shapes with angle $0^{\circ}$, was increased to 157.2[%] to 263.2[%] in the power and was increased to 110[%] to 250[%] in the power coefficient. Moreover, when the Shape 5 Fin length of main-blade doubled, the power was 70.8[%] when compared with Shape 1 and 27.5[%] with shape 4.If the main-blade geometry equals shape 1 in the case structure, The power of Case1 was increased to 13.3[%] when compared with Case2. Also, the power coefficient was increased to 15.4[%]. When sub-blade angle was $45^{\circ}$, main-blade was better than the Fin type than the Bended type. The power of Case4 was increased to 47[%] when compared with Csae1 and increased to 13.6[%] with Case 3. Also, the power coefficient was 46.7[%] when compared with Case 1 and 15.8[%] with Case 3.