• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.258-258
• /
• 2017

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.717-724
• /
• 2002

To investigate the behavior of air-shaft and existing tunnel by excavating the small-diameter shaft into the existing tunnel, prototype air-shaft was constructed and analyzed in this study. Geotechnical characterization was conducted by boring and rock cores obtained were tested in the laboratory. Field monitoring including radial and tangential stresses and displacements was conducted with the 3-dimensional numerical analysis of prototype air-shaft. Results of field monitoring were compared with the numerical results. The results showed that maximum displacement of 2.11mm and maximum tangential stress of 54.0 kg/$\textrm{cm}^2$ were obtained during shaft excavation near the right shoulder of the existing tunnel. The comparison of these field measurements with 3-dimensional numerical analysis showed that much more higher stress was measured during excavation compared to the numerical results even though the trends of stress and displacement were similar.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.431-438
• /
• 1999

Vertical congressive and horizontal pile load tests were performed to a instrumented large diameter (D : 1,000 mm) drilled shaft. A drilled shaft was penetrated into the weathered soil and weathered rock. PMT was done for evaluation of properties for these strata. It was expected to be difficult to get undisturbed samples of weathered soils and rocks. Thus. PMT was done at the several selected depths. In those strata, to prevent the test bore hole from collapsing, bentonite slurry was used for making the test bore hole. In this study. soil properties was evaluated by means of PMT results and estimating method (direct method, the Memard method) of vertical pile capacity and horizontal pile behaviors were summarized. Also, vertical and horizontal pile capacity were calculated using PMT and pile load test results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.36-43
• /
• 2004

Most of pile foundations are fixed head condition, but lateral loading test for pile is performed under free head condition generally In this study, a lateral loading test for a large diameter drilled shaft was performed under the fixed pile head and the free pile head condition, where lateral displacement along the pile depth was measure. Test results and theoretical values were compared and analyzed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.180-186
• /
• 1996

Using carbon steel or ceramic as a shaft material of monolithic and slited insert ring clamped on it. The fitting strengths of the sgrink fitted assemblies measured from room temperature to 30$0^{\circ}C$ and following conclusions were obtained as results of this investigation. 1) The fitting condition under which the shrink fitted assemble was stronger than that using simple fit in high temperature. 2) When both material of the 30mm-diameter shaft and 55mm-diameter boss are SM45C the clamping torque is increased 2.7times as the interference increases 3 times from 20${\mu}{\textrm}{m}$ at the contact length of 6mm monolithic fit. 3) When only the material of boss is changed to STS 304 the clamping torque is increased at the rate of 37.3N.m per 1mm increase of the contact length at the interference of 50${\mu}{\textrm}{m}$ monolithic fit.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.45-51
• /
• 2012

The main goal of this paper is to establish an interference tolerance for determining optimal amount of clearance in the shaft-bearing system supported by radial ball bearings. The 2-D frictional contact model was employed for the FE analysis between the shaft and the inner raceway. Several examples were simulated using different material properties for the solid shaft. Efforts were focused on the deformation applied in the radial direction to select suitable bearings. The analysis results showed that the initial axial preload applied on the bearings plays a significant role to reduce bearing fatigue life. The proposed design parameters obtained by numerical simulations can approximately predict a rate of bearing life reduction as a function of shaft diameter ratio. This analysis can also be used to calculate the optimal initial radial clearance in order to obtain a shaft-bearing system design for high accuracy and long life.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.123-128
• /
• 1997

In-situ bearing metal temperature and shaft vibration are measured for an unload type and a preload type, m=0.87, of vertical guide bearing for hydraulic pump-turbines. Guide bearing is a tiltingpad type journal bearing consisting of eight pads whose diameter is 1,450 mm. Rotational speed is 450 rpm. Both the bearing metal temperature and the shaft vibration are very high in the unload type but are slight in the preload type, comparatively. The bearing metal temperature is decreased due to the increase of cooling effect by the increase of preload and the shaft vibration is decreased due to the increase of bearing stiffness. It is concluded that the preload effect of a guide bearing for hydraulic pump-turbines has a large influence on the bearing metal temperature and the shaft vibration.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.530-535
• /
• 2006

The Pusan clays are soft and thick deposits and in some places, they reach even up to 50-70m. So, the pile foundations are inevitable in almost all cases. But they are significantly expansive when the length of the pile reaches about 70m. In this study, a comprehensive parametric study has been carried out in order to reduce the pile length and number of piles required in turn the cost of the foundation for particular building. A belled shaft pile has been optimized for a typical soil profile using the PLAXIS (FEM code). These results have shown a new direction of the pile foundation in Pusan, Korea. The results including the variation of contact pressures at the bottom of the bell, optimization of the angle of the bell and height of the bell in terms of the diameter of the shaft. And also, the design curves have been generated so that they can be directly used for design of belled shaft foundations. However, the structural strength criterion is being checked in the concerned laboratory.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.5
• /
• pp.135-143
• /
• 2004

In the land section of marine bridge construction site, to confirm the end bearing of large diameter drilled shaft constructed in the fault zone which was discovered unexpectedly, the hi-directional end loading tests were performed. The objectives of this study are to confirm the end bearing of the pile constructed in fault zone and the increasing effect of end bearing after grouting the base ground beneath the pile toe. After grouting the pile base ground, the settlement of pile base decreased considerably and the pile base resistance increased more than twice.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.4 no.1
• /
• pp.59-65
• /
• 1967

Since the screw propellers were adopted as ship propulsion devices, the replacement of propeller shaft due to damage was mostly of fatigue failure due to the alternative stresses [1],[2]. To prevent such a failure, hence, it is suggested that careful attention should be paid to account of the alternative stresses on the design stage of the propeller shafts. In connection with this fact the Ship Classification Societies' Rules are regarded simply as guidance for preliminary determination of the shaft diameter. In this paper, limiting the topic to the small and medium-sized motor ships, an evaluation of the Rules formulae to a theoretical based on Soderberg's correlation [5] between the factor of safety and the resultant stresses obtained by application of the maximum shear theory is done. For this purpose eleven (11) ships built recently in Korea were taken as a species(refer to table 2. in text). In the end the following conclusions are made: (1) In general the Rules formulae give considerably larger size of the propeller shaft diameter than that derived from theoretical calculation, that is, about 7% more in AB and BV Rules, and about 20% more in LR and KR-NK Rules. (2) LR Rule gives the largest size of all, and AB Rule is mostly closed value to the theoretical. (3) The formular of the AB Rule is considered to be of the simplest in utilization and of the reasonable.