• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 추계학술발표 개요집
• /
• pp.19-34
• /
• 1996

A review was made of fatigue failures of nuclear power plant components in Japan, which were experienced in service and during periodical inspection. No case has been recently reported of a service fatigue failure of a reactor pressure vessel itself, excluding nozzle corner cracks, that occurred many years ago. But, service fatigue failures have been occasionally experienced in piping systems, pumps, and valves, on which fatigue design seems to have been inadequately applied. The causes of fatigue failures can be divided into two categories: mechanical-vibration-induced fatigue and thermal-fluctuation-induced fatigue. Vibration-induced fatigue failure occurs more frequently than is generally thought. The lesson gleaned from the present survey is a recognition that a service fatigue failure may occur due to any one or a combination of the following factors: (1) lack of communication between designers and fabrication engineers, (2) lack of knowledge about a possibility of fatigue failure and poor consideration about the effects of residual stresses, (3) lack of consideration on possible vibration in the design and fabrication stages, and (4) lack of fusion or poor penetration in a welded joint.

• 자동차안전학회지
• /
• 제5권2호
• /
• pp.51-56
• /
• 2013

In vehicle's door wiring harness (W/H) system is more toward to arrange a passenger compartment than a hinge and a weatherstrip. An opening/closing member of a vehicle is attached to a vehicle by a hinge in a manner enabling easy opening and closing of the opening/closing member. Such members include doors, such as side-doors and rear doors, and other opening/closing members, such as trunk lids. This article gives some insight into the dimensioning process, with special focus on large deflection analysis of wiring harness(W/H) in vehicle's door structures for durability problem. The Finite elements analysis for door wiring harness(W/H) is used for residual stresses and dimensional stability with bending flexible. Durability test data for slam test specimens were compared with the numerical predicted fatigue life for verification. The final testing of the component combines the effects of these microstructural features with the complex stress state arising from the combined service loading and residual stresses.

• Journal of Welding and Joining
• /
• 제20권3호
• /
• pp.84-90
• /
• 2002

The strength and the life of welded components are affected extensively by the residual stresses distributed around their weldments not only under static loads, but also fatigue loads. The residual stress can be superimposed with externally applied loads, so that unexpected deformations and failures of members will be occurred. These residual stresses are not kept constant, but relaxed or redistributed during in service. Under static loads the relaxation takes place when the external stress superimposed with the residual stress exceeds locally the yield stress of material used. It is shown that under fatigue loads the residual stress is considerably relieved by the first or flew cycle loading, and then gradually relaxed with increasing loading cycles. In this study the phenomenon and mechanism of the stress relaxation by mechanical means were investigated and a model to predict quantitatively the residual stress relaxation for the case of static and fatigue loading condition was proposed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.274-277
• /
• 2004

The most important mode of subcritical crack growth is primary water stress corrosion crack, which was the reported mechanism from the root cause analysis of the crack in the bimetallic welds. Stress corrosion crack growth evaluations was carried out for several flaw shapes of both axial and circumferential flaws, using the steady-state stresses including residual stresses. This evaluation considered the possibility of additional flaws in the primary loops of nuclear power plant, even though no such flaws have been identified by Ultrasonic Test. Consequently, Results show that the predicted flaw sizes will determine acceptability for continued service and maintenance.

• KCI Concrete Journal
• /
• 제12권1호
• /
• pp.69-77
• /
• 2000

The reinforced concrete(RC) flexural members strengthened with steel plate/CFS at soffit have initial stresses and strains in reinforcements and concrete caused by the service loads at the time of retrofitting works. These initial residual stresses and strains of strengthened beams may affect the flexural performance of the rehabilitated beams. The objective of this study is to evaluate and verify the effectiveness of rehabilitation by external bonded steel plates and CFS to the tension face of the beams under three conditions of pre-loading. Thirteen beam specimens are tested and analyzed. Main test parameters are pre-loading conditions, strengthening materials and reinforcement ratio of specimens. The effect of test parameters on the strengthened beams is analyzed from the maximum load capacity, load-deflection relationship, state of stress of the materials. crack propagation phase, and failure modes. Both test results and design formulas of ACI Code provisions are compared and evaluated.

• Journal of applied mathematics & informatics
• /
• 제39권1_2호
• /
• pp.31-43
• /
• 2021

A homogeneous circular disk undergoing a contact force is considered to investigate the thermo-elastic characteristics, and the inquiry is based on the variations of outer surface temperature and angular velocity. The intensity of stresses grows with the increase of outer surface temperature, and the circumferential strain reacts more sensitively to the change of outer surface temperature than the radial strain. In general, higher angular velocity produces; (i) larger expansion in the radial direction, (ii) smaller displacement in the circumferential, (iii) diminished intensity in the stresses. It is demonstrated that outer surface temperature and angular velocity are critical factors in the determination of thermo-elastic characteristics of homogeneous circular disks subjecting to a contact force. The results obtained can be applied on the design of a homogeneous circular cutter to promote proper and reliable thermos-elastic characteristics in service by the proper operation of these parameters.

• 한국화재소방학회논문지
• /
• 제27권5호
• /
• pp.26-31
• /
• 2013

원전의 가압기 지지대에 사용되는 볼트는 설계 시 안전율 측면에서 충분한 경도의 볼트를 사용하지만, 현장실사를 통해 허용 경도 범위를 초과하는 볼트가 일부 확인되었다. 이러한 높은 경도의 볼트는 응력부식 및 재료의 파괴인성이 취약하고, 가압기는 부식에 취약한 환경이므로 이 부분에 대한 검토가 필요하다. 따라서 본 연구에서는 현장실사를 통해 원전 가압기 지지대에 사용되는 볼트의 경도를 측정하였고, 이를 통해 응력부식과 부재의 파괴인성에 의한 균열을 제한할 수 있는 최대 허용응력을 계산하였다. 또한 정상운전 및 사고운전 시 발생할 수 있는 지지대 볼트의 응력을 수치해석 프로그램인 ANSYS를 사용하여 예측하였고, 이 응력이 응력부식을 제한할 수 있는 최대 허용응력 내에 있는 지 검토하였다. 검토 결과 정상 및 사고운전 조건에서 볼트의 응력은 응력부식에 대해 허용응력 안전 기준치를 만족하는 것으로 나타났다. 그러나 향후 가압기 지지대의 구조물 체결방법을 체결 절차에 반영하여 정비 시 가압기의 건전성을 확보할 수 있도록 검토가 필요하다.

• 대한조선학회논문집
• /
• 제38권4호
• /
• pp.75-82
• /
• 2001

건조 후 수행하는 수압시험 또는 화물의 적재 등과 같은 정하중은 파랑변동하중에 비하여 선체구조물에 상당히 큰 응력을 유발한다. 이러한 정하중이력에 의하여, 선체구조물의 응력집중으로 인해 피로강도가 문제되는 용접이음부에서는, 재료의 탄소성 거동에 의하여 초기용접잔류응력이 상당히 이완될 것으로 예상된다. 따라서, 이러한 용접이음부의 피로강도를 평가할 때에는 이완된 잔류응력의 영향을 고려하는 것이 보다 합리적이다. 본 연구에서는 선체구조물의 여러 가지 용접형태 중 Padding plate가 용접된 형태에 대하여 정하중이력($0.5{\sigma}Y,\;0.85{\sigma}Y$)에 의한 초기 용접잔류응력의 변화를 측정하며, 잔류응력의 변화가 피로강도에 미치는 영향을 검토한다.

• International Journal of Advanced Culture Technology
• /
• 제7권1호
• /
• pp.14-19
• /
• 2019

Stress affects the type of adaptation required for each case and the type of social support is also different. In order for social support to have a buffer effect on stress, we want to understand how to measure social support and support according to specific stress situations. Therefore, this study examines coping behaviors of community service workers exposed to these job stresses and examines the effect of support system (family support, peer support, superior support) on coping behavior. The purpose of this study is to investigate the effects of stress, coping resources and coping behaviors of community service workers. In this study, self - report method was used to investigate the questionnaire using structured questionnaires. In this study, the statistical program was used for data analysis and hierarchical regression analysis.

• 환경영향평가
• /
• 제4권2호
• /
• pp.123-130
• /
• 1995

The equipment composed of many complicated electronic stuffs undergoes diverse stresses caused by mechanical vibrations during its service. Thus, to ensure its proper operation in the field a simulated vibration test has to be carried out in the laboratory with the Vibration Qualification Level, the test specification, which can include the real environment. In this paper we intent to deal with method and procedure for determining the Vibration Qualification Level so as to estimate the vibration-endurance for the equipment precisely.